1. Introduction
The BRIGHTWIN IG80-2 Ignition Coil Tester is a specialized diagnostic tool designed for testing ignition coils in automobiles and motorcycles. It supports testing of 12V gasoline engine ignition coils, 12-24V natural gas engine ignition coils, and motorcycle ignition coils. This instrument allows for comprehensive testing of 2-wire, 3-wire, 4-wire, 5-wire, 6-wire, and 7-wire ignition coils, providing adjustable speed and power settings to simulate various operating conditions.
2. Safety Information
WARNING: The tester itself does not produce high voltage, but the ignition coil being tested will produce 20-30KV voltage when working. Always pay attention to safety when using this instrument.
- Keep all parts of the human body away from the ignition coil and connection lines during testing to avoid high-voltage electric shocks.
- Ensure the ignition coil, connection wires, and tester are kept away from flammable, explosive, and other dangerous goods and environments during testing.
- This instrument is specialized testing equipment for auto repair. Non-professionals should use this instrument only under the guidance of qualified auto repair technicians.
3. Package Contents
Verify that all items listed below are included in your package:
- Tester Host (IG80-2)
- Discharge Connection Wire
- Plugs (for connections)
- Set of Connecting Wires
- Power Cord
- User Manual (this document)
4. Specifications
| Parameter | Value |
|---|---|
| Model Number | IG80-2 |
| Brand Name | BRIGHTWIN |
| DIY Supplies | Electrical |
| Origin | Mainland China |
| Certification | CE, RoHS |
| Display Size | 3.0 - 4.9 Inches |
| Functions | Auto Motorcycle Ignition Coil Tester |
| Operating Power Supply | 12-24VDC |
| Speed Adjustable Range | 120-8400 r/min |
| Ignition Power Adjustment | High, Medium, Low |
| Ignition Signal Amplitude | 5V, 12V adjustable (Default 5V) |
| Size | 10 x 7.5 x 2.5 cm |
| Package Dimensions (L x W x H) | 12 x 5 x 7 cm |
| Package Weight | 0.5 kg |
| Battery Included | No |
The IG80-2 is capable of testing ignition coils for gasoline engines, natural gas engines, and motorcycles, including 2-wire, 3-wire, 4-wire, 5-wire, 6-wire, and 7-wire configurations.
5. Product Components
Familiarize yourself with the main components and controls of the IG80-2 tester:
- Coil Type Socket: For connecting coil-type ignition coils.
- Module Type Socket: For connecting module-type ignition coils.
- Discharge Needle Socket: For connecting the discharge wire.
- Ignition Signal Amplitude Selection (5V/12V Switch): Adjusts the signal voltage. Default is 5V.
- Engine Speed Display: Shows the simulated engine speed in x120 r/min.
- Ignition Power Indicators (L, M, H): Indicates Low, Medium, or High ignition power.
- Ignition Signal Light: Illuminates when an ignition signal is detected.
- Engine Speed ADJ Knob: Adjusts the simulated engine speed.
- Ignition Power ADJ Knob: Adjusts the ignition power (Low, Medium, High).
- START Button: Initiates the testing process.
- Power Input (DC 12-24V): Connection for external power supply.
The rear panel provides specific connection points for different ignition coil types:
- Ignition Signal Amplitude Switch (5V/12V): Selects the signal amplitude.
- Module Type Ignition Coil Connections: Dedicated terminals for Positive (+), Signal (IG), and Ground (GND).
- Coil Type Ignition Coil Connections: Dedicated terminals for Positive (+), Signal (IG), and Ground (GND).
- Discharge Needle Socket: Connects to the discharge wire.
6. Setup
The IG80-2 tester requires an external power supply. It is recommended to use a car battery or a 12-24V regulated power supply with an output current of ≥10A.
- Connect Power Supply: Plug the power cord into the DC 12-24V power input on the tester. Connect the other end to a suitable 12-24V power source (e.g., car battery or regulated power supply).
- Prepare Ignition Coil: Identify the type of ignition coil you are testing (coil type or module type) and its wiring configuration (2-wire, 3-wire, 4-wire, etc.). Refer to Section 5 for understanding coil types.
- Connect Discharge Wire: Insert one end of the discharge connection wire into the discharge needle socket on the tester. Position the other end (the needle) near the high-voltage output of the ignition coil, ensuring a safe gap for spark observation.
7. Operation
Follow these general steps to test an ignition coil:
- Ensure the tester is powered on and the discharge wire is safely positioned.
- Connect the ignition coil to the appropriate socket on the tester (Coil Type or Module Type) using the provided connecting wires. Pay close attention to the polarity (+, IG, -) and pin arrangement, as this varies between different coil models.
- Select the correct ignition signal amplitude (5V or 12V) using the switch on the rear panel, if applicable for your coil.
- Press the START button to begin the test.
- Adjust the Speed ADJ knob to simulate different engine speeds (120-8400 r/min) and observe the spark.
- Adjust the Power ADJ knob to test the ignition coil's spark condition under different power levels (Low, Medium, High).
- Observe the spark at the discharge needle and the Ignition Signal Light on the tester. A consistent, strong spark indicates a healthy coil.
- To stop the test, press the START button again.
7.1. Ignition Coil Wiring Diagrams
Correct wiring is crucial for accurate testing. The pin arrangement order can differ significantly between various ignition coil models. Always ensure the positive, negative, and ignition signal pins are connected correctly.
7.1.1. Two-Wire Ignition Coil (Coil Type)
Connect to the "Coil type" socket using the + and IG terminals. The other wire is typically ground.
7.1.2. Three-Wire Ignition Coil (Coil Type)
Connect to the "Coil type" socket using the +, IG, and - terminals.
7.1.3. Three-Wire Ignition Coil (Module Type)
Connect to the "Module type" socket using the +, IG, and - terminals.
7.1.4. Four-Wire Ignition Coil (Module Type)
Most four-wire coils are module types. Connect to the "Module type" socket. Note that some Toyota four-wire coils may not use an IGF connection.
7.1.5. Six- and Seven-Wire Ignition Coils
For six- and seven-wire ignition coils, refer to the specific pinout for your coil model. The diagrams below illustrate common configurations for these types, showing connections for positive (+), negative (-), and multiple ignition signal (IG) lines.
7.1.6. Specific Ignition Coil Wiring Examples
The following image provides examples of wiring diagrams for various common ignition coil brands. Always verify the correct pin arrangement for your specific coil model.
7.2. Video Demonstration
Watch this video for a visual guide on connecting and operating the IG80-2 Ignition Coil Tester.
8. Maintenance
- Keep the tester clean and free from dust and moisture.
- Store the device in a dry, cool place when not in use.
- Avoid dropping or subjecting the tester to strong impacts.
- Do not attempt to open or repair the device yourself. Contact qualified service personnel if maintenance is required.
9. Troubleshooting
9.1. Ignition Coil Does Not Spark
If the ignition coil does not produce a spark during testing, consider the following:
- Connection Cable: Double-check that all connection cables are correctly and securely attached to both the tester and the ignition coil.
- Coil Type/Module Type Position: Ensure the ignition coil is connected to the correct socket (Coil Type or Module Type) on the tester. Incorrect insertion can prevent operation.
- Ignition Signal Amplitude: Verify that the 5V/12V Signal Range switch is set correctly for the coil being tested. Try flipping the switch if unsure.
- Power Supply Current: The power supply current might be too low. Ensure your external power supply provides at least 10A. The tester has an overcurrent protection circuit that automatically disconnects the power if the current is too large.
- Damaged Ignition Coil: The ignition coil itself may be faulty or damaged.
10. User Tips
- Verify Wiring: A common issue is incorrect wiring. Always refer to the specific wiring diagrams for your ignition coil model and ensure all connections (positive, negative, signal) are correctly made to the tester's appropriate sockets (coil type or module type). If you encounter issues, re-check your connections first.
- Power Supply: Ensure your 12-24V power supply can deliver at least 10A to avoid the tester's overcurrent protection from activating.
- Coil Identification: Understand whether your ignition coil is a "coil type" (no internal power amplifier module, primary coil resistance ~1 Ω) or "module type" (internal power amplifier module, resistance >100 Ω) to use the correct tester socket and wiring.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
A PDF version of this user manual may be available for download. Please check the product page or contact support for the link.