FGHGF IKOHS Netbot S12 Haier T550W /T560H DEXP MMB-300

Contents

Robotic Vacuum Cleaner Accessory User Manual

For IKOHS Netbot S12, Haier T550W/T560H, DEXP MMB-300 Robot Vacuum Cleaners

Brand: FGHGF | Model: IKOHS Netbot S12 Haier T550W /T560H DEXP MMB-300

1. Introduction

This manual provides essential information for the installation, use, maintenance, and troubleshooting of your FGHGF Robotic Vacuum Cleaner replacement accessories. These accessories are designed to maintain the optimal performance of your compatible robot vacuum cleaner.

2. Warning & Safety Information

  • CAUTION: Do not disassemble the unit unless you are a qualified engineer.
  • Avoid contact with sharp objects to prevent damage to the accessories.
  • Keep accessories out of reach of children and pets.

3. Product Overview

The FGHGF Robotic Vacuum Cleaner Accessories include various replacement parts such as side brushes, HEPA filters, and mop cloths, designed for specific robot vacuum cleaner models.

3.1 Compatible Models

  • IKOHS Netbot S12
  • Haier T550W
  • Haier T560H
  • DEXP MMB-300

3.2 Available Accessory Types

  • Side Brushes (e.g., 3 pairs)
  • HEPA Filters (e.g., 5 pieces)
  • Mop Cloths (e.g., 5 pieces)
  • Combination Sets (e.g., Set 1: Side Brushes + HEPA Filters; Set 2: Side Brushes + HEPA Filters + Mop Cloths)
Three pairs of side brushes for robot vacuum cleaner
Side Brushes
Five HEPA filters for robot vacuum cleaner
HEPA Filters
Five mop cloths for robot vacuum cleaner
Mop Cloths
Set including side brushes and HEPA filters
Combination Set (Side Brushes + Filters)
Comprehensive set of side brushes, mop cloths, and HEPA filters
Comprehensive Set

4. Installation Instructions

To install any accessory, ensure your robot vacuum cleaner is powered off and unplugged. Carefully remove the old accessory (if applicable) and install the new accessory back into its original position in the unit. Refer to your robot vacuum cleaner's main manual for specific instructions on accessing and replacing parts.

4.1 Side Brush Installation

  1. Turn the robot vacuum cleaner upside down.
  2. Locate the side brush(es). Depending on your model, they may be secured with a screw or clip.
  3. Remove the old side brush.
  4. Align the new side brush with the mounting post and press down firmly until it clicks into place or secure with the screw/clip.

4.2 HEPA Filter Installation

  1. Open the dustbin compartment of your robot vacuum cleaner.
  2. Remove the dustbin.
  3. Locate the filter housing within the dustbin.
  4. Remove the old HEPA filter.
  5. Insert the new HEPA filter, ensuring it is seated correctly to maintain proper filtration.
  6. Close the dustbin and reinsert it into the robot vacuum cleaner.

4.3 Mop Cloth Installation

  1. Locate the mop pad attachment on your robot vacuum cleaner.
  2. Remove the used mop cloth.
  3. Attach the new mop cloth to the designated area, ensuring it is securely fastened (e.g., via Velcro or clips).

5. Maintenance

Regular maintenance of your vacuum cleaner accessories is crucial for optimal cleaning efficiency and extending the machine's service life.

5.1 Cleaning Frequency

  • Side Brushes: Inspect weekly and clean regularly to remove tangled hair and debris. Replace every 3-6 months or when visibly worn.
  • HEPA Filters: Tap clean weekly to remove dust. Do not wash. Replace every 2-3 months, or more frequently if you have pets or allergies.
  • Mop Cloths: Wash after each use. Replace every 1-3 months depending on usage and wear.

5.2 Cleaning Instructions

  • Side Brushes: Use a small brush or your fingers to remove hair and debris. If bent, you can soak them in warm water for a few minutes to reshape.
  • HEPA Filters: Gently tap the filter against a trash can to dislodge dust. A small brush can be used to clean between the pleats. Do NOT rinse with water.
  • Mop Cloths: Hand wash or machine wash with mild detergent. Air dry completely before reattaching to the robot.

6. Troubleshooting

6.1 Common Issues and Solutions

Issue: Accessory feels loose after installation.
Solution: Simply re-secure it. Ensure it is properly aligned and clicked into place or screwed in tightly.
Issue: Reduced cleaning performance.
Solution: Check if filters are clogged, side brushes are worn or tangled, or mop cloths are dirty. Clean or replace as necessary.
Issue: Side brushes are bent or deformed.
Solution: Remove the brushes and soak them in warm water for 5-10 minutes. This can help them regain their original shape. Ensure they are completely dry before reinstallation.

7. Specifications

FeatureDetail
Product TypeVacuum Cleaner Parts (Filters, Side Brushes, Mop Cloths)
Brand NameFGHGF
MaterialPP, Fabric, PVC
High-concerned chemicalNone
Compatible ModelsIKOHS Netbot S12, Haier T550W, Haier T560H, DEXP MMB-300
Package Dimensions (Approx.)Length: 20 cm, Width: 15 cm, Height: 10 cm
Package Weight (Approx.)0.17 kg

8. User Tips

  • Always have spare filters and brushes on hand to ensure continuous optimal performance of your robot vacuum.
  • For best results, clean side brushes and filters more frequently if you have pets or high-traffic areas.
  • Ensure mop cloths are thoroughly cleaned and dried to prevent mildew and maintain hygiene.

9. Support

If you encounter any quality-related issues or require further assistance with your FGHGF Robotic Vacuum Cleaner Accessories, please contact our customer service for support.

For a detailed user manual in PDF format, you can refer to the official document: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.