JIKONG JK-B1A8S20P

Contents

JIKONG JK BMS B1A8S20P Smart Battery Management System User Manual

Model: JK-B1A8S20P / JK-B2A8S20P

1. Introduction

The JIKONG JK BMS B1A8S20P is an advanced active balance Battery Management System designed for Li-Ion, LiFePo4, and LTO battery packs. It provides comprehensive protection and monitoring features to ensure the safety and longevity of your battery system. This manual will guide you through the installation, operation, and maintenance of your JIKONG JK BMS.

JIKONG JK BMS B1A8S20P unit.
JIKONG JK BMS B1A8S20P unit.
JIKONG JK BMS B1A8S20P key features and specifications.
JIKONG JK BMS B1A8S20P key features and specifications.

2. Specifications

The JIKONG JK BMS offers robust features for battery management:

  • High-concerned chemical: None
  • Charging Current: 200A
  • Usage Scenario: Power BMS, 3C Digital BMS
  • Certification: CE, FCC, RoHS
  • Balance Function: Active Balanced BMS
  • Hardware or Smart: SMART BMS
  • Charge and Discharge Port: Common Port BMS
  • Type: LI-ION Battery BMS
  • Function: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
  • Temperature sensor: Yes
  • Active Balance: Yes
  • Heating function: Yes
  • Communication: RS485/BT
  • Battery Strings: 3S-8S
  • Battery Type: Li-ion/LiFePo4/LTO
Detailed technical specifications table for various JIKONG BMS models.
Detailed technical specifications table for various JIKONG BMS models.

3. Package Contents

Upon opening your JIKONG JK BMS package, you should find the following items:

  • JIKONG JK BMS Unit
  • Operating Manual
  • Screws (x4)
  • NTC (Temperature Sensor, 40cm)
  • Switch (50cm)
  • CAN Cable (25cm)
  • Balance Wires (70cm)
Contents of the JIKONG JK BMS package.
Contents of the JIKONG JK BMS package.

4. Setup Instructions

4.1 Hardware Connection

Carefully follow the wiring diagram to connect the protection board to your battery pack, load, and charger. Ensure all connections are secure and correct.

  • Connect the balance wires to the corresponding battery cells.
  • Ensure the last power cord is connected to the main positive pole of the battery pack.
  • Connect the load and charger to the designated ports on the BMS.
  • The total voltage of the battery pack must be greater than 20V (Default BMS) or 10V (for 4S BMS) before starting up the BMS.
Wiring diagram for JIKONG JK BMS connecting to a battery pack, load, and charger.
Wiring diagram for JIKONG JK BMS connecting to a battery pack, load, and charger.
JIKONG JK BMS B2A8S20P-HC showing connection ports.
JIKONG JK BMS B2A8S20P-HC showing connection ports (NTC, UART/GPS, RS485/CAN, ACC, Display/Switch, Sampling Port, Heating Cable).
Detailed view of JIKONG JK BMS ports including temperature sensor, LCD, RS485, and heat function.
Detailed view of JIKONG JK BMS ports including temperature sensor, LCD, RS485, and heat function.

4.2 Initial Activation

Use the display activation button or the additional switch to activate the BMS after all connections are made.

5. Operating Instructions

5.1 Mobile App Connection

The JIKONG JK BMS can be monitored and configured via a mobile application:

  • Ensure your mobile device's Bluetooth and GPS are turned on.
  • Download the app:
    • iOS: Search "JIKONG BMS" in the App Store.
    • Android: Search "JK BMS" in the Google Store.
  • Open the app and click on the top left corner to search for devices.
  • Select your device name to connect. The default password is 1234.
JIKONG Smart BT APP displaying battery monitoring data.
JIKONG Smart BT APP displaying battery monitoring data.
Screenshots of the JIKONG BT Mobile App for monitoring and settings.
Screenshots of the JIKONG BT Mobile App for monitoring and settings.

5.2 Initial Parameter Settings

For the first start-up, you will need to set parameters:

  • Access the settings menu in the app. The default password for settings is 123456.
  • Set the correct number of battery strings and the battery type (Li-ion, LiFePo4, or LTO).
  • After setting, return to the real-time status page to check the battery status. Ensure no error messages are prompted and the system operates normally. Blue indicates the highest cell voltage, and red indicates the lowest.

5.3 Smart Energy Working Modes

The BMS features different working modes to optimize power consumption and battery life:

  • Storage Mode: In transportation, offline, or wireless transmission off mode, the BMS enters storage mode, which does not consume battery pack current.
  • Normal Working Mode: When the charger is inserted in storage mode and off mode, the BMS will immediately return to normal working mode. All protection, equalization, and communication functions will resume normal operation.
  • Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage. The BMS automatically shuts down when a cell falls below the shutdown voltage.
  • Standby Mode: When the battery pack is in a static state (no charge and discharge current and no equilibrium current), the BMS will automatically enter standby state after a set time (1-30 days can be set).
Diagram showing smart energy working modes: Storage, Normal, Shutdown, and Standby.
Smart energy working modes: Storage, Normal, Shutdown, and Standby.

6. Maintenance

To ensure optimal performance and longevity of your JIKONG JK BMS:

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the BMS unit clean and free from dust and moisture.
  • Monitor battery cell voltages and temperatures via the app to detect any anomalies early.
  • Ensure the BMS firmware is up to date by checking the app or manufacturer's website for updates.
  • The heating wires of JK-B1A8S10P-HC, JK-B1A8S20P-HC, and JK-B2A8S20P-HC have been replaced with black ones. This is a cosmetic change and does not affect functionality.

7. Troubleshooting

This section addresses common issues you might encounter:

  • BMS not powering on: Ensure the battery pack voltage is above the minimum threshold (20V for default, 10V for 4S BMS) and all power connections are secure. Try activating with the display button or external switch.
  • App not connecting: Verify Bluetooth and GPS are enabled on your mobile device. Ensure the BMS is active. Double-check the connection password (default: 1234).
  • Incorrect cell readings: Recheck balance wire connections to ensure they are correctly seated and in the right order.
  • Over-protection warnings: The BMS has six security protections (Overcharge, Short Circuit, Over-discharge, Overcurrent, Cable Drop/Poor Contact, Over-temperature). Identify which protection is triggered via the app and address the underlying cause (e.g., reduce load, check charger settings, inspect wiring).
Diagram illustrating six security protection features of the BMS: overcharge, short circuit, over-discharge, overcurrent, cable drop/poor contact, over-temperature.
Six Security Protection features of the JIKONG JK BMS.

8. User Tips

  • For advanced users, consider checking for the latest hardware versions (e.g., V17 or V19) if specific features like Victron CAN support or charge voltage request parameters are crucial for your application.
  • Always ensure the BMS is properly configured for your specific battery type (Li-ion, LiFePo4, LTO) and cell count to prevent damage and ensure accurate monitoring.
  • Utilize the mobile app's real-time monitoring to keep an eye on individual cell voltages and overall battery health, especially during initial setup and heavy usage.

9. Warranty and Support

For technical support, warranty claims, or further inquiries, please refer to the official JIKONG BMS resources:

Please retain your purchase receipt for any warranty-related services.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.