Taidacent TDJL-XKT511-27

Contents

Taidacent 500mA 5V Inductive Charger Wireless Charging Module Kit

Model: TDJL-XKT511-27

1. Introduction

This manual provides instructions for the Taidacent 500mA 5V Inductive Charger Wireless Charging Module Kit, model TDJL-XKT511-27. This upgraded and optimized universal high-efficiency wireless power supply module is designed with the XKT-511 chip for transmission and the XKT-3202 chip for reception. It offers a stable and efficient solution for wireless power transfer, particularly suitable for charging lithium batteries.

2. Safety Information

Please read and understand the following safety precautions before using the module:

  • Ensure all connections are correct before applying power. Incorrect wiring can damage the module or connected devices.
  • Do not exceed the specified input voltage of 5V.
  • Avoid short-circuiting the output terminals.
  • Keep the module away from water, moisture, and extreme temperatures.
  • Handle components with care to prevent electrostatic discharge damage.
  • This module is intended for use by individuals with basic knowledge of electronics.

3. Package Contents

The kit typically includes the following components:

  • 1 x Wireless Power Transmitter Module (XKT511-27 based)
  • 1 x Wireless Power Receiver Module (XKT-3202 based)
  • 2 x Inductive Coils (25mm outer diameter, 16mm inner diameter, 0.7mm thickness, 5uH inductance)
Taidacent Wireless Charging Module Kit components
Figure 1: Overview of the Taidacent Wireless Charging Module Kit, showing both transmitter and receiver modules with their respective coils.

4. Specifications

ParameterValue
Model NumberTDJL-XKT511-27
Accessory TypeCharger Accessories
Input Voltage5V
Receive Output Voltage5V
Receive Max Current Output500mA
Transmitter Board Dimensions10mm x 15mm
Receiver Board Dimensions8mm x 15mm
Coil Dimensions (Outer Diameter)25mm
Coil Dimensions (Inner Diameter)16mm
Coil Thickness0.7mm
Coil Inductance5uH
OriginMainland China

Output Current vs. Charging Distance

Charging DistanceOutput Current
1mm500mA
2mm500mA
3mm500mA
4mm470mA
5mm420mA
6mm340mA
7mm280mA
8mm230mA
9mm200mA
10mm160mA
11mm120mA
12mm80mA

5. Setup

Follow these steps to set up your wireless charging module:

  1. Identify Components: Distinguish between the transmitter module and the receiver module. The transmitter module is based on the XKT-511 chip, and the receiver module is based on the XKT-3202 chip. Both modules are connected to their respective inductive coils.
  2. Transmitter and Receiver Modules with Coils
    Figure 2: Labeled image showing the transmitter and receiver modules, each with a 25mm 5uH coil. The transmitter typically has a slightly larger board.
  3. Connect Transmitter: Connect a 5V power source to the input wires of the transmitter module. Ensure correct polarity (red wire for positive, black wire for negative).
  4. Connect Receiver: Connect the output wires of the receiver module to the device you wish to charge (e.g., a lithium battery charging circuit). Ensure correct polarity. The receiver provides a 5V output at up to 500mA.
  5. Refer to Wiring Diagram: For detailed electrical connections, consult the provided schematic diagram.
  6. Wiring Diagram for XKT-511 Transmitter and XKT-3202 Receiver
    Figure 3: Schematic diagram illustrating the internal circuitry and connections for the XKT-511 transmitter and XKT-3202 receiver modules. This diagram shows the 5V input to the transmitter (top) and the 5V output from the receiver (bottom).
  7. Position Coils: Place the receiver coil in close proximity to the transmitter coil. Optimal performance is achieved when the coils are aligned concentrically and as close as possible.

6. Operating Instructions

Once the modules are set up and powered:

  1. Ensure the transmitter module is powered with a stable 5V supply.
  2. Bring the receiver coil close to the transmitter coil. The wireless power transfer will begin automatically.
  3. Monitor the charging status of your connected device.
  4. Refer to the "Output Current vs. Charging Distance" table in the Specifications section for expected performance at various distances. For maximum efficiency and current, keep the coils as close as possible (e.g., 1-3mm).

7. Maintenance

To ensure the longevity and proper functioning of your wireless charging module:

  • Keep the modules clean and free from dust and debris.
  • Avoid exposing the modules to excessive heat, cold, or humidity.
  • Do not bend or damage the inductive coils, as this can affect performance.
  • Regularly check connections for any signs of wear or corrosion.

8. Troubleshooting

If you encounter issues with your wireless charging module, consider the following:

  • No Power Output:
    • Check if the 5V input to the transmitter is correctly connected and powered.
    • Ensure the receiver coil is properly aligned and within the effective charging distance of the transmitter coil.
    • Verify all wiring connections for correct polarity and secure contact.
  • Low Charging Current:
    • Reduce the distance between the transmitter and receiver coils.
    • Ensure the coils are perfectly aligned (concentric).
    • Check for any metallic objects between the coils that might interfere with the magnetic field.
  • Module Overheating:
    • Ensure adequate ventilation around the modules.
    • Verify that the load connected to the receiver does not exceed the maximum current output (500mA).

9. User Tips

  • Optimal Alignment: For best performance, ensure the centers of the transmitter and receiver coils are perfectly aligned. Even a slight misalignment can significantly reduce efficiency and output current.
  • Distance Matters: As shown in the specifications, the output current drops significantly with increasing distance. Keep the coils as close as possible for faster and more efficient charging.
  • Integration: When embedding the module into a project, consider the placement of the coils to allow for easy and consistent alignment during use.

10. Warranty and Support

This product is covered by a standard manufacturer's warranty. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.