1. Introduction
The AISET XMTE1000-2 Intelligent Temperature Controller, model XMTE-1401B-Y(N), is a precision instrument designed for accurate temperature regulation in various industrial and laboratory applications. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device.
Figure 1: Front view of the XMTE1000-2 Temperature Controller, showing PV/SV displays and control buttons.
2. Safety Information
Please read and understand all safety precautions before installing or operating the controller. Failure to do so may result in personal injury or damage to the equipment.
- Ensure the power supply voltage matches the controller's specifications.
- Disconnect power before making any wiring connections or performing maintenance.
- Installation and wiring should be performed by qualified personnel.
- Do not operate the controller in environments with excessive moisture, dust, corrosive gases, or high vibration.
- Avoid touching internal components when power is applied.
3. Package Contents
Verify that all items are present and undamaged upon unpacking:
- 1 x AISET XMTE1000-2 Intelligent Temperature Controller (Model: XMTE-1401B-Y(N))
4. Specifications
| Feature | Specification |
|---|---|
| Model Number | XMTE1000-2 XMTE-1401B-Y(N) |
| Type | Intelligent Temperature Controller |
| Temperature Range | 0-400°C |
| Input Type | K-type Thermocouple |
| Operating Voltage | 187-242VAC, 50Hz |
| Power Consumption | 5VA |
| Origin | Mainland China |
5. Installation & Wiring
5.1 Mounting
The controller is designed for panel mounting. Ensure adequate space for ventilation and access to wiring terminals. Cut a panel opening of appropriate dimensions for the controller body.
5.2 Wiring Diagram
Refer to the wiring diagram below for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the unit or connected equipment.
Figure 2: Side view showing the wiring diagram for the XMTE1000-2 controller.
Terminal Connections:
- Terminals 1, 2, 3: ALM (Alarm Output)
- Terminals 4, 5, 6: INTPT (Input - typically for K-type thermocouple)
- Terminal 7: + (Positive terminal for input, if applicable)
- Terminals 8, 9, 10: OUTPUT (Main Control Output)
- Terminals 11, 12: VOL OUT (Voltage Output, if applicable)
- Terminals 13, 14: POWER (Power Supply Input: 187-242VAC, 50Hz)
Figure 3: Rear view of the XMTE1000-2 controller, displaying the terminal block for wiring connections.
6. Operation
6.1 Front Panel Overview
- PV Display (Red): Shows the current Process Value (actual temperature).
- SV Display (Green): Shows the Set Value (desired temperature).
- ALM Indicator: Illuminates when an alarm condition is met.
- OUT Indicator: Illuminates when the control output is active.
- AT Indicator: Illuminates during auto-tuning.
- SET Button: Used to enter parameter setting mode or confirm settings.
- < (Shift) Button: Used to shift digits during parameter setting.
- ^ (Up) Button: Used to increase values or navigate menus.
- V (Down) Button: Used to decrease values or navigate menus.
6.2 Basic Operation
- Power On: After correct wiring, apply power to the controller. The PV and SV displays will light up.
- Monitoring Temperature: The red PV display shows the current temperature measured by the thermocouple.
- Setting Temperature (SV):
- Press the SET button once. The SV display will flash.
- Use the ^ and V buttons to adjust the desired temperature. Use the < button to shift between digits for faster adjustment.
- Press SET again to confirm the new SV. The controller will begin to regulate the temperature to this set point.
6.3 Parameter Setting (Advanced)
To access advanced parameters (e.g., PID settings, alarm types, input calibration), typically a long press of the SET button or a combination of buttons is required. Consult the full technical manual for detailed parameter descriptions and adjustment procedures. Exercise caution when modifying advanced parameters, as incorrect settings can affect performance or safety.
7. Maintenance
- Cleaning: Keep the controller's front panel clean. Use a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically check wiring connections for tightness and signs of wear or corrosion.
- Environment: Ensure the operating environment remains within specified conditions (temperature, humidity, absence of corrosive substances).
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/Display off | No power supply; Incorrect wiring; Blown fuse. | Check power connections; Verify wiring; Replace fuse if necessary (by qualified personnel). |
| PV display shows 'HHHH' or 'LLLL' | Thermocouple open circuit or reverse connection; Input type mismatch. | Check thermocouple wiring and polarity; Ensure correct input type is configured. |
| Temperature control is unstable | Incorrect PID parameters; Sensor interference. | Perform auto-tuning; Check sensor for interference or damage. |
| Output not activating | SV not reached; Output wiring issue; Output parameter setting. | Verify SV and PV; Check output wiring; Review output control parameters. |
9. User Tips
- For optimal performance, ensure the thermocouple is correctly positioned and makes good thermal contact with the object or area being measured.
- If experiencing temperature overshoot or undershoot, consider performing the auto-tuning function (if available) to optimize PID parameters for your specific application.
- Always double-check your wiring against the diagram before applying power to prevent damage.
10. Warranty and Support
This product is designed for reliability and performance. In the event of a malfunction or if you require technical assistance, please contact the seller or manufacturer's support channels. Keep your purchase records for warranty claims.
For any questions or support needs, please reach out to customer service. We are committed to ensuring customer satisfaction.