BAOFENG UV-K61

Contents

Baofeng UV-K61 Walkie Talkie User Manual

Model: UV-K61 | Brand: BAOFENG

1. Introduction and Safety Warnings

Thank you for choosing the Baofeng UV-K61 Multi-Band Amateur Radio. This device utilizes advanced technology for reliable communication in demanding environments. It offers stable and reliable long-distance communication with a sleek and compact design, featuring emergency alarm, DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode. This manual provides essential information for safe and effective use.

1.1 Regulations and Safety Warnings

FCC Regulatory Conformance: This equipment complies with Class B digital device limits (Part 15 of FCC Rules). It generates and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference. Interference can be corrected by reorienting the receiving antenna, increasing separation between equipment and receiver, or connecting to a different circuit. Unauthorized changes or modifications may void the user's authority to operate the equipment.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Compliance with RF Exposure Standards: The radio complies with RF energy exposure standards and guidelines from the FCC, ANSI/IEEE C95.1:2005, and Canada RSS102 Issue 5 March 2015.

RF Exposure Compliance and Control

Guidelines:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if operational requirements are not met.

Operating Instructions:

  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit, release to receive.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always use an approved holder, holster, case, body harness, or correct clip.
  • Use of non-approved antennas, batteries, and accessories may cause the radio to exceed FCC RF exposure guidelines.
  • Contact your local dealer for optional accessories.

Precautions for Portable Terminals:

  • Do not operate in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate near any medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication equipment is prohibited.

Important Tips

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an airbag, do not place the product in the airbag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation. Allow it to cool.
  • Handle the product with care.
  • Do not disassemble, modify, or repair the product and its accessories without authorization.

Precautions for Batteries

Charging Prohibitions:

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not charge a wet battery; dry it with a soft, clean cloth first.
  • Do not charge a battery suffering deformation, leakage, or overheating.
  • Do not charge with an unauthorized charger.
  • Do not charge in a location with strong radiation.
  • Overcharge is prohibited as it may shorten battery life.

WARNING! When keys, ornamental chains, or other electric metals contact the battery terminal, the battery may be damaged or injure a human. Short-circuited battery terminals will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

2. Package Contents

The Baofeng UV-K61 transceiver comes with the following items:

  • 1 Radio body
  • 1 Lithium-Ion battery pack
  • 1 Instruction Manual
  • 1 Belt Clip
  • 1 Desk charger (With wall-wart)
  • 1 Antenna
  • 1 Wrist Belt
  • 1 Type-C USB Cable

If any item is missing, please notify your Baofeng / Pofung dealer.

Baofeng UV-K61 Accessories and Parameters
Figure 2.1: Included accessories and key parameters for the UV-K61.

3. Features and Functions

The Baofeng UV-K61 offers a wide range of features for versatile communication:

  • 1.54" TFT large screen, full keyboard, fully open menu operation.
  • Multi-Band Scanning Receiver: FM 65-108 MHz (RX only), AM 108-136 MHz (Air Frequency Receiving), 350-390 MHz (RX only), 136-174 MHz (TX/RX), 220-260 MHz (TX/RX), 400-520 MHz (TX/RX), 520-600 MHz (RX only).
  • Wireless Copy Frequency: Allows direct copying of frequencies from other radios without programming software.
  • 999 Memory Channels: Store a large number of frequencies and settings.
  • Type-C USB Charging: Convenient charging via Type-C port, compatible with various power sources like car chargers, power banks, or laptops.
  • DTMF Function: Dual-Tone Multi-Frequency for advanced signaling.
  • Dual Watch / Dual Reception: Monitor two channels simultaneously.
  • FM Radio: Broadcast FM radio receiver (87.5-108 MHz).
  • NOAA Weather Radio: Reception of NOAA Weather Radio channels in the United States and Canada, with weather alert function.
  • VOX (Voice Activated Transmit): Hands-free operation.
  • LED Flashlight: Built-in LED spotlight for emergency or low-light situations.
  • Alarm Function: Emergency alert feature.
  • Scanner Function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan.
  • PC & Manual Programmable: Program settings via computer software or directly through the keypad.
  • Battery Save Function: Extends battery life.
  • Keypad Lock: Prevents accidental changes to settings.
  • Frequency Step: Selectable steps (2.5K, 5.0K, 6.25K, 8.33K, 10K, 12.5K, 20K, 25K, 30K, 50K, 100KHz).
  • Programmable Repeater Offset: For repeater communication.
  • Busy Channel Lock Out: Prevents transmission on occupied channels.
  • Ten (10) levels of Squelch adjustment.
  • End of transmission tone (Roger Beep).
  • Two (2) pins for Kenwood accessory port.
Baofeng UV-K61 Key Features
Figure 3.1: Visual summary of UV-K61 key features.
Baofeng UV-K61 AM Aviation Band Receiving
Figure 3.2: Detailed frequency bands, including AM Aviation Band receiving capabilities.
Baofeng UV-K61 Display and VOX
Figure 3.3: The 1.44-inch HD color screen and VOX (Voice Activated Transmit) feature.
Baofeng UV-K61 Usage Scenarios
Figure 3.4: Examples of usage scenarios for the UV-K61, such as camping, hunting, mountaineering, and transport.

4. Getting Started

4.1 Battery Information

The Li-ion battery pack is not charged at the factory. Charge it before first use or after extended storage (more than 2 months). Full capacity is reached after 2-3 full charge/discharge cycles. Replace the battery if its operating time decreases significantly.

Charger Supplied: Use only the specified charger. Other chargers may cause explosion or personal injury. Charge the battery if the radio displays a low battery warning.

Use Caution with the Li-ion Battery:

  • Do not short the battery terminals or throw the battery into a fire.
  • Do not attempt to remove the casing from the battery pack.
  • Charge the battery between 5℃-40℃ (40°F - 105°F).
  • Turn off the radio before inserting it into the charger.
  • Do not interrupt the charging cycle until the green light is on.
  • Do not recharge a fully charged battery.
  • Do not charge a damp battery or radio; dry it first.

4.2 How to Charge

Base Charger:

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange.
  2. Plug the battery or the radio into the charger. Ensure good contact. The indicator light turns red, indicating charging.
  3. Charging takes approximately 2-5 hours. The lamp turns green when fully charged.

Type-C USB Charger:

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery.
  3. Connect the other end of the micro-USB charger to a wall power outlet (or other compatible USB power source).
  4. An empty battery will be fully charged in 4 hours. The battery meter on the LCD will indicate charging.

Note: It is recommended to power OFF your radio while charging. If powered on, you may not be able to transmit if the battery is completely empty. Allow time for the battery to charge to 1 bar before transmitting. For optimal battery life, remove the radio from the charger within 6 hours; do not store it connected to the charger.

Baofeng UV-K61 Charging Methods
Figure 4.1: Illustration of Type-C Fast Charging and Base Charging methods.

4.3 LED Indicator Status

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

Note: Trouble means battery too warm, battery short-circuited, or charger short-circuited.

4.4 How to Store the Battery

  • Store the battery at 80% discharged.
  • Keep it in a low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.

4.5 Installation of Accessories

Before using the radio, ensure the battery pack is attached and charged.

Installing/Removing the Antenna:

  1. Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  2. Removing: Turn the antenna counter-clockwise to remove it.

Installing the Belt Clip:

  1. At the back of the radio, remove the two parallel screws mounted above the battery. Thread them through the holes on the belt clip as you screw them back into the radio body.
  2. Removing: Unscrew counter-clockwise to remove the belt clip.

Installing the Battery Pack:

  1. Ensure the radio is turned off by rotating the power/volume knob counter-clockwise.
  2. Align the battery in parallel with the radio body, with the lower edge of the battery about 1-2cm below the radio's edge.
  3. Slide the battery upward along the guide-rails until it clicks into place.

Removing the Battery Pack: Press the battery release above the battery pack, then slide the battery downward.

Installing the Additional Speaker/Microphone (Optional): Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Speaker/Microphone Jack Diagram
Figure 4.2: Diagram for installing an external speaker/microphone.

5. Radio Overview

5.1 Buttons and Controls of the Radio

Baofeng UV-K61 Labeled Diagram
Figure 5.1: Labeled diagram of the Baofeng UV-K61 radio, showing all buttons and components.
  1. Antenna
  2. PTT Key (Push to Talk)
  3. Flashlight / Alarm Switch
  4. Power / Volume knob
  5. A / B Select Key
  6. SWEEP Key
  7. MENU Key
  8. Color LCD
  9. Accessory Jack
  10. V/M-VFO/MR Mode Key
  11. Speaker
  12. EXIT Key
  13. Type-C charging indicator
  14. Type-C charging port
  15. LED flashlight
  16. Microphone
  17. Battery release latch
  18. SK1-Programmable key (flashlight/alarm switch)
  19. SK2-Programmable Key (Radio/Monitor)
  20. Keypad

5.2 Main Keypad Controls

  • V/M: Short press to switch VFO/MR mode. Press and hold to switch channel display mode (CH, Frequency, Name).
  • A/B: Short press to switch between A (upper) and B (lower) displays. Press and hold to switch Dual Watch mode (Double Wait / Signal Wait / Off).
  • SWEEP/Band: Short press to enter one key sweep.
  • EXIT: Short press to return to the menu or previous menu.
  • *: Press and hold to lock or unlock the keyboard. In transit mode, short press for inverted frequency (display R)/offline (display T).
  • #: Short press to enter DTMF dial. Press and hold to scan on and off.
  • 0_space: Press and hold to enter weather switch to select weather channel.

5.3 Programmed Key (SK1/SK2)

The [SK1] and [SK2] keys can be programmed for different functions. This can be done via the radio's menu (Menu -> Radio Setting –Press and Longpress SK1, SK2) or PC software (Buttons section).

OptionFunctionality
NoneNo function is assigned to this button.
SCANTo enable or disable the Scan feature.
MONITORTo enable or disable the Monitor feature.
FlashlightTo enable or disable the flashlight feature.
FM RadioTo enable or disable the FM Radio feature.
SOSTo enable or disable the emergency alarm feature.
One Touch SweepTo enable or disable the One Touch Sweep feature.
1750HzTransmits 1750Hz Tone Burst.
One Touch CallTo make a call or send a message to the preset contact or implement an auxiliary feature.
Battery DisplayCheck the current battery capacity voltage.
PowerSwitch the power between super high, high, low power.
VOXTo enable or disable the VOX feature.

5.4 Status Indications (Top LED)

LED IndicationWhat it Indicates
Constant GreenReceiving Signal
Constant RedTransmitting signal
Flashes GreenMonitor mode/Scanning Receiving

5.5 LCD Icon Summary

Baofeng UV-K61 LCD Display
Figure 5.2: Example of the UV-K61 LCD display showing various icons and information.
IconMeaning
CTCCTCSS enabled
DCSDCS enabled
VFOFrequency Mode
DWDual watch enabled
H/LTransmit power level indicator (High/Low)
NNarrowband enabled
VOXVOX enabled
MxxxMemory channel
A/BA band (upper) and B band (lower) displays
ArrowIndicates active band or channel
DTDTMF side tone from radio speaker (DT-ST, ANI-ST, DT+ANI)
2T2TONE signaling enabled for current channel/frequency
5T5TONE signaling enabled for current channel/frequency
BDCBDC1200 signaling enabled for current channel/frequency
+Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX.
-Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX.
RReverse function enabled
TTalkaround has been activated, off grid at the central turntable. The transmission frequency is equal to the receive frequency.

6. Basic Operations

6.1 Power On/Off

Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". After about one second, you should hear a double beep and the display will show a message or flash the LCD. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode".

Turning the unit off: Rotate the Volume/Power knob counter-clockwise until you hear a "click". The unit is now off.

  • Voice Prompt Setting: Press [MENU] to enter Menu>>35/65 Voice.
  • Power-on Display setting: Press [MENU] to enter menu>>39/65 Power On Display to select Picture, Message, Voltage.
  • If a power-on password is set, enter the correct password. Press [MENU] to enter the menu >>41/65 Password.

6.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease. Be careful not to turn it too far, as you may inadvertently turn your radio off.

6.3 Main Band/Sub Band Switch

Press the [A/B] key to switch between the A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.

6.4 VFO/Channel Switch

Press the [V/M] key to switch between Frequency (VFO) Mode and Memory (MR) mode (also called Channel mode). VFO mode is useful for experimentation, while MR mode is more practical for everyday use with pre-programmed channels.

6.5 Frequency (VFO) Mode

In VFO mode, use the ▲/▼ keys to increment or decrement the frequency according to the set frequency step. You can also input frequencies directly using the numeric keypad with kilohertz accuracy.

WARNING! Transmitting on unauthorized frequencies is illegal. Always ensure you are authorized to operate on a frequency before transmitting. Listening is generally legal.

6.6 Channel (MR) Mode and Channel Selection

Press the [V/M] key to switch to Channel (MR) mode.

  • Operation 1: Use the ▲/▼ navigation key to select the channel.
  • Operation 2: Input channel numbers directly using the keyboard (e.g., [0][1][2] for channel 12).

If voice prompt is enabled, the channel number will be broadcast by voice.

6.7 Making a Call

  • Channel mode call: Select a channel, hold down the [PTT] key, and speak into the microphone. The red LED will be on.
  • Frequency mode call: Switch to VFO mode, input the desired frequency, hold down the [PTT] key, and speak into the microphone. The red LED will be on.
  • Receive a call: Release the [PTT] key to answer. The green LED will be on when receiving.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

6.8 Emergency Alert

The Emergency Alert feature signals for help. To activate, press the pre-programmed [SOS] key. Press it again to exit.

  • Alarm Type Setting: Press [MENU] to enter Menu>>49/65 Alarm Mode. Options include local alarm, alarm code + background tone, alarm code + alarm tone (none), and alarm code + alarm tone.
  • The unit can set up 10 alarm systems and configure them to channels via CPS program software.

WARNING: The Emergency Alert feature should only be used in an actual emergency.

6.9 FM Radio (FM)

Press [MENU] key to go to the Menu -> Press/Longpress of "SK1/SK2" as [FM Radio], and turn on or off the radio by pressing the preset [FM Radio] key.

Station Search:

  • Short press the #z key to search for an FM channel. The screen displays 'Seeking...' and the radio locks the searched station.
  • Press and hold the #z key to enter radio search mode. The radio will automatically save the searched frequency as a radio channel.
  • Use ▲/▼ to select the radio channel.
  • Directly input familiar radio frequency by numeric keys (e.g., 96.9MHz, input 969).
  • Press to switch the 65.0MHz/76.0MHz radio band.

To exit FM radio mode, short press the preset [FM Radio] key or [EXIT] key.

6.10 Radio Interrupt

  • On: When FM radio is used, you can still receive or transmit on the channel.
  • Off: When FM radio is used, the radio will not permit a transmission or reception.

6.11 Monitor

In standby, press the pre-programmed [Monitor] key to enter Monitor mode. This function allows you to monitor weak signals. Press the [Monitor] key again to exit.

6.12 Keypad Lock

To enable or disable the keypad lock, press and hold the * key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds from the menu.

6.13 Frequency Reversal

A short momentary press of the * key enables the reverse function. This allows you to listen to the repeater's input frequency by reversing your transmit and receive frequencies.

6.14 TX Repeaters Tone

Tone-bursts (1000Hz, 1450Hz, 1750Hz, 2100Hz) are used for repeater activation. Before using, the SK1/SK2 programmable key must be defined as the “1750Hz” function. Press the pre-programmed [1750Hz] key to send tone-bursts.

6.15 NOAA Weather/Weather Alert

Your radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 channels. In standby mode, press and hold the [0] key to enter NOAA channel scanning reception state. Enable this channel to display the icon on the first line.

Use ▲/▼ to switch between NOAA channels from WX1 to WX10. Alternatively, press and hold the # key to auto-search. These channels are RX only.

Weather Alert: Press [MENU] >> Weather Alert. Options:

  • Off: Disables the Weather Alert function.
  • On: Enables the Weather Alert function.

With Weather Alert enabled, the radio guards the radio channel and weather channel, cycling through them. Activating the Weather Alert feature and receiving a 1050 HZ alert signal will cause a loud beep and switch the radio to weather broadcast mode.

Method 1: Press [MENU] key to go to the main Menu -> Press/Longpress of "SK1/SK2" as [One Touch Sweep], and enter the frequency search mode by pressing the preset [One Touch Sweep] key.

Method 2: Press the SWEEP key (One Touch Sweep) to enter the frequency search mode.

When using OneTouch Search, the unit acts as a receiver. The screen will display “Seeking” and the indicator light will be yellow. Successful seeking displays the search frequency and CTCSS/DCS, and turns on the speaker.

  • Press the [MENU] key to save the search frequency and CTCSS/DCS to the channel.
  • Press and hold the [PTT] key to make a callback.

7. Advanced Features

7.1 Scanner

The radio has a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels.

To enable the scanner, press and hold the #z key for about two seconds. Change scanning direction with ▲/▼ keys. Press and hold the #z key to exit scanning mode.

Frequency Range: In frequency mode, the sweep range can be precisely set by inputting start and end values via the keyboard (e.g., 144146 for 144.000-146.000MHz).

Channel Scan Range: In channel mode, the scan range can include all stored channels or only added channels.

  • All: All channels stored.
  • Memory Scan: Scans channels added to memory.

Scan Modes: The scanner operates in three modes:

  • Time Operation (TO): Stops when a signal is detected, then resumes scanning after a preset timeout.
  • Carrier Operation (CO): Stops when a signal is detected, then resumes scanning after the signal disappears.
  • Search Operation (SE): Stops when a signal is detected and remains stopped. Press #z again to resume.

7.2 Scan Sub-Code (CTCSS/DCS)

To search for a CTCSS code:

  1. In VFO mode, enter a known frequency (e.g., 144.525).
  2. Press [MENU] + 20 to enter “20/65 Scan SubCode”.
  3. Select CTCSS using ▲/▼.
  4. Press [MENU] to scan CTCSS codes. When a valid code is found, it stays on that code and the speaker turns on.
  5. Press [MENU] to store the scanned code and exit. The CTC icon will be displayed. Press and hold PTT to callback.

To search for a DCS code, follow the same steps, selecting DCS in step 3.

Sub-Code Scan Memory: Scanned CTCSS/DCS codes can be stored as TX only, RX only, or both TX and RX codes for the current channel or frequency mode.

  1. Press [MENU] + 21 to enter “21/65 Scan Memory”.
  2. Press [MENU] to enter Scan Memory setting, then use ▲/▼ to select:
  • ENCODER: Stores the scanned code as TX CTCSS/DCS.
  • DECODER: Stores the scanned code as RX CTCSS/DCS.
  • ALL: Stores the scanned code as both TX and RX CTCSS/DCS.
  1. Press [MENU] to save and return.

7.3 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method used for automation systems and remote control, common in amateur radio repeaters. The UV-K61 has full DTMF implementation, including A, B, C, and D codes. Numerical keys, *, and #z correspond to DTMF codes. A, B, C, and D are located in [MENU], ▲/▼, and [EXIT] keys respectively.

To send DTMF codes, press the key(s) while holding down the PTT key.

DTMF Frequencies and Corresponding Codes:

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

DTMF Enc: Set a DTMF ID as the default call ID for the current channel. Press the PTT key to transmit the selected DTMF ID. Edit the DTMF ID in Menu or with the PC programming software.

7.4 2Tone Enc & 5Tone Enc

Set a 2Tone or 5Tone as the default call ID for the current channel. Press the PTT key to transmit. Edit these tones in the PC programming software before selection.

7.5 Dual Watch

Dual Watch allows monitoring two channels simultaneously. The radio features single-receiver Dual Watch functionality, locking the transmit frequency to one of the monitored channels.

Enabling/Disabling Dual Watch mode:

  1. Press [MENU] + 42 to enter “42/65 Dual Watch”.
  2. Press [MENU] to select.
  • OFF: Disables dual-watch.
  • Double Wait: Enables dual-watch, DW icon displayed.
  • Signal Wait: Enables single-watch, transmits/receives on main channel only.
  1. Press [MENU] to confirm.
  2. Press [EXIT] to return.

Alternatively, press and hold [A/B] key to switch Double Wait / Signal Wait / Off dual watch mode.

7.6 Manual Programming (Channels Memory)

Memory channels store commonly used frequencies. The radio features 640 memory channels, each capable of holding receive/transmit frequencies, power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Frequency Mode vs. Channel Mode:

  • Frequency Mode (VFO): Used for temporary frequency assignments or quick field programming.
  • Channel Mode (MR): Used for selecting preprogrammed channels.

Example 1: Programming a Channel Repeater Offset with CTCSS Tone (e.g., New memory in Channel 28: RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), TX CTCSS tone 123.0)

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] key to set the radio to VFO mode.
  3. [MENU] [5] [MENU] 123.0 [MENU] (Selects desired TX encode tone)
  4. [MENU] [1][2] [MENU] [0][5] [0][0] [MENU] (Enter OFFSET frequency)
  5. [MENU] [1][1] [MENU] Plus [MENU] (Select offset direction)
  6. Enter RX frequency (e.g., 43255000)
  7. [MENU] [1][7] [MENU] [2][8] [MENU] (Enter the same channel)
  8. Press [V/M] key to return to MR mode. The channel number will reappear.

Example 2: Programming a Simplex Channel with CTCSS tone (e.g., New memory in Channel 28: RX = 432.6500 MHz, TX CTCSS tone 123.0)

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] key to set the radio to VFO mode.
  3. [MENU] [5] [MENU] 123.0 [MENU] (Selects desired TX encode tone)
  4. Enter RX frequency (e.g., 43265000)
  5. [MENU] [1][7] [MENU] [2][8] [MENU] (Enter the same channel)
  6. Press [V/M] key to return to MR mode. The channel number will reappear.

7.7 Repeaters Programming

To program repeaters, ensure you know the transmit and receive frequencies and are authorized to use them.

  1. Press [V/M] key to set the transceiver to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (your receive) frequency.
  3. Press [MENU] [1][2] [MENU] to get the offset frequency.
  4. Use the numeric keypad to enter the specified frequency offset.
  5. Press [MENU] to confirm and save.
  6. Press [MENU] [1][1] [MENU] to get the offset direction.
  7. Use the ▲/▼ keys to select plus (positive) or minus (negative) offset.
  8. Press [MENU] to confirm and save.
  9. Optional: Save to memory (see Manual Programming) and set up CTCSS.
  10. Press [EXIT] to exit the menu.

Note: If experiencing problems, check settings or use the 1750Hz tone burst for certain Amateur Radio repeaters. Contact your local amateur radio club for assistance.

7.8 Amateur Radio Setup

For typical Amateur radio setup, the following settings are recommended:

  • Turn off Squelch Tail Elimination (Tail) features (menu items 48).
  • Turn roger beep (ROGER) off (menu item 38).
  • Set bandwidth to Wide (menu item 08).
  • Turn DCS and CTCSS off (menu items 04 through 07).
  • Turn Signaling code off and SQL Mode (menu items 10 and 11).
  • Set and view DTMF ANI, 5TONE ANI, BDC1200 ANI, Radio Name (menu items 61 through 64).

9. Troubleshooting Guide

If you encounter issues with your Baofeng UV-K61, refer to the table below for common problems and solutions. If these solutions do not resolve the issue, please contact your dealer for technical support.

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts.Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent.The battery voltage may be low. The volume level may be low. The antenna may be loose or incorrectly installed.Recharge or replace the battery. Increase the volume. Turn off the radio, then remove and reattach the antenna.
You cannot communicate with other group members.The speaker may be blocked. The frequency or signaling type may be inconsistent with other members. You may be too far away from other members.Clean the surface of the speaker. Verify that your TX/RX frequency and signaling type are correct. Move towards other members.
You hear unknown voices or noise.You may be interrupted by radios using the same frequency. The radio in analog mode may be set with no signaling.Change the frequency, or adjust the squelch level. Request your dealer to set signaling for the current channel to avoid interference.
You are unable to hear anyone because of too much noise and hiss.You may be too far away from other members. You may be in an unfavorable position (e.g., blocked by high buildings or underground area). It may be the result of external disturbance (e.g., electromagnetic interference).Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

10. Technical Specifications

Below are the technical specifications for the Baofeng UV-K61. Note that all specifications may be modified without prior notice or liability.

GENERAL
Channel Capacity640
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 15 hours @ 5 watts
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions (LxAxP)64x121x35mm
Radio Weight240g
TRANSMITTER
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450 MHz (Canadian version)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
RF Output Power5 Watts Max
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
RECEIVER
Frequency Range108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%
Baofeng UV-K61 vs UV-5R Comparison
Figure 10.1: Comparison of UV-K61 features against UV-5R.

11. User Tips

  • Wireless Frequency Copy: Utilize the wireless copy function (press the 'SEARCH' button) to quickly clone frequencies from other radios without needing a computer. This is especially useful for on-the-fly setup with friends.
  • Type-C Charging Convenience: Take advantage of the Type-C charging port for flexible power options. You can charge your radio using a power bank, car charger, or laptop, making it ideal for outdoor activities like camping or hiking.
  • Manual Programming: While PC software offers comprehensive control, remember that many settings, including adding/deleting channels and adjusting VOX/squelch levels, can be done directly through the radio's keypad menu. This is handy when you don't have access to a computer.
  • NOAA Weather Alerts: Keep the NOAA Weather Alert function enabled, especially during outdoor excursions, to receive timely weather broadcasts and alerts.

12. Warranty and Support

Disclaimer: The accuracy and completeness of the contents of this manual are diligently sought. However, we do not bear any responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without notice. No copy, modification, translation, or dissemination of this handbook may be made in any form without prior written authorization.

For further assistance or technical support, please contact:

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com or www.pofungshop.com

User Manual (PDF): A detailed user manual in PDF format is available for download. You can view it here: Baofeng UV-K61 User Manual (PDF)

© 2023 BAOFENG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.