Introduction
This manual provides instructions for the Philips SPK7607 Multi-Pairing Wireless Mouse. This advanced mouse offers versatile connectivity options, including 2.4G wireless and Bluetooth 5.0, allowing connection to up to three devices simultaneously. It features a low-noise design, five programmable buttons, and adjustable DPI settings for enhanced productivity and comfort.
Package Contents
- Philips SPK7607 Wireless Mouse
- USB Receiver (for 2.4G wireless connection)
- User Manual
- Note: AA battery not included.
Setup
1. Battery Installation
- Locate the battery compartment on the underside of the mouse.
- Open the battery compartment cover.
- Insert one AA battery, ensuring correct polarity (+/-).
- Close the battery compartment cover.
- Turn on the mouse using the power switch located on the underside.
2. Connecting via 2.4G Wireless Mode
- Ensure the mouse is powered on.
- Take the USB receiver out of its storage slot (usually on the underside of the mouse).
- Plug the USB receiver into an available USB port on your computer.
- The mouse should automatically connect. If not, ensure the mouse is in 2.4G mode (check the mode switch on the bottom, if present, or follow Bluetooth pairing instructions to ensure it's not in Bluetooth mode).
3. Connecting via Bluetooth Mode (Multi-Pairing)
The SPK7607 supports multi-pairing, allowing you to connect to up to three devices via Bluetooth.
- Ensure the mouse is powered on.
- Press and hold the Bluetooth pairing button (located on the underside of the mouse) for approximately 3 seconds. The LED indicator on the mouse will flash blue, indicating it is in pairing mode.
- On your device (computer, tablet, smartphone), navigate to the Bluetooth settings.
- Search for available devices and select "Philips SPK7607" from the list.
- Once connected, the LED indicator will stop flashing.
- Repeat these steps for up to two additional devices. The mouse will remember the paired devices.
Operating Instructions
1. Switching Between Connected Devices
If you have paired the mouse with multiple devices via Bluetooth, you can switch between them by briefly pressing the Bluetooth pairing button on the underside of the mouse. Each short press will cycle through the paired devices.
2. Adjusting DPI (Sensitivity)
The mouse features an adjustable DPI button, allowing you to change the cursor sensitivity on the fly. Press the DPI button (located behind the scroll wheel) to cycle through the available DPI settings: 800, 1200, 1600, 2400, and 3200 DPI.
3. Using Side Buttons
The two side buttons on the left side of the mouse typically function as "Forward" and "Backward" buttons in web browsers and file explorers, enhancing navigation efficiency.
4. Low Noise Operation
The Philips SPK7607 is designed with low-noise click buttons, providing a quiet working environment without disturbing others.
Maintenance
1. Cleaning
- Use a soft, dry cloth to wipe the surface of the mouse.
- For stubborn dirt, slightly dampen the cloth with water or a mild cleaning solution.
- Avoid using harsh chemicals or abrasive materials.
- Do not allow liquids to enter the mouse.
2. Battery Replacement
When the mouse performance degrades or the LED indicator suggests low battery, replace the AA battery following the installation steps in the "Setup" section.
3. Storage
When not in use for extended periods, turn off the mouse to conserve battery life. Store the USB receiver in its designated slot on the underside of the mouse to prevent loss.
Troubleshooting
- Mouse not responding:
- Ensure the mouse is powered on.
- Check the battery level and replace if necessary.
- For 2.4G mode, ensure the USB receiver is securely plugged into a working USB port. Try a different USB port.
- For Bluetooth mode, ensure Bluetooth is enabled on your device and the mouse is properly paired. Try re-pairing the mouse.
- Ensure the mouse is not too far from the receiver/device.
- Cursor lagging or erratic movement:
- Clean the optical sensor on the underside of the mouse.
- Ensure you are using the mouse on a suitable surface (not highly reflective or transparent).
- Reduce interference by moving other wireless devices away from the mouse and receiver.
- Check battery level.
- Cannot switch between devices:
- Ensure all devices are within range and have Bluetooth enabled.
- Verify that the mouse was successfully paired with each device initially.
- Briefly press the Bluetooth button to cycle through connections.
Specifications
| Feature | Detail |
|---|---|
| Model | SPK7607 |
| Connection Type | 2.4G Wireless, Bluetooth 5.0 |
| Number of Buttons | 5 |
| DPI Settings | 800 / 1200 / 1600 / 2400 / 3200 |
| Operation Mode | Laser |
| Power Supply | 1 x AA Battery |
| Dimensions (L x W x H) | 115.3 x 70.5 x 40.5 mm |
| Weight (without battery) | 80g |
| Hand Orientation | Right |
| System Requirements | Windows 7/8/10/11, Mac OS, Android, iOS |
User Tips
- For optimal performance, use the mouse on a non-reflective, opaque mouse pad.
- To extend battery life, turn off the mouse when not in use for prolonged periods.
- Experiment with different DPI settings to find the sensitivity that best suits your workflow.
- Utilize the multi-pairing feature to seamlessly switch between your desktop, laptop, and tablet.
Warranty and Support
Philips products are manufactured to the highest standards and undergo rigorous quality checks. This product is covered by a manufacturer's warranty. For detailed warranty information and technical support, please refer to the warranty card included with your purchase or visit the official Philips support website.
Please retain your proof of purchase for warranty claims.
