Introduction
The TBK 958ZU is a new generation 4W UV laser engraving and marking machine designed for precision work on various materials, particularly for separating phone LCDs and glass back housings. It features AI intelligent language control, a large touch screen, and a high-power cold laser for efficient and safe operation. This manual provides essential information for the safe and effective use of your device.
Safety Information
- Always wear appropriate eye protection when operating the laser machine.
- Ensure the eye protection safety door is closed during operation to effectively isolate harmful light.
- Operate the machine in a well-ventilated area or ensure the activated carbon filtration exhaust system is functioning correctly to manage fumes.
- Do not attempt to bypass safety features.
- Keep hands and other body parts clear of the laser path and work area during operation.
- Disconnect power before performing any maintenance or cleaning.
Setup
1. Unpacking and Inspection
Carefully unpack all components from the wooden packaging. Verify that all items listed in the packing list are present and undamaged.
- TBK 958ZU Laser Machine
- Metal Card
- Hexagon Wrench Set
- Power Cable
- Wireless Mouse and Keyboard
2. Placement
Place the machine on a stable, level surface with adequate ventilation around the rear cooling fans.
3. Power Connection
Connect the power cable to the machine and a suitable power outlet (110~220V). Ensure the power switch is in the OFF position before connecting.
Operating Instructions
1. Power On and Interface Navigation
Turn on the machine. The large touch screen will display the main interface. You can navigate using the touch screen or the provided wireless mouse and keyboard.
2. Voice Control (AI Intelligent Language Control)
The machine supports AI intelligent language control. You can use voice commands for certain operations, such as "Hello TBK" to activate and "Focus" or "Start" to initiate actions. This feature allows for hands-free operation.
3. Selecting Operation Mode
From the main interface, select the type of device (e.g., Phone, Tablet, Watch) and the desired operation (e.g., Remove back cover, Remove screen, Remove holder). The machine features a rich drawing library covering mainstream mobile phone models for precise positioning.
4. Placing the Workpiece and Auto Focus
- Open the eye protection safety door.
- Carefully place the device (e.g., phone) onto the work platform within the 180x180mm work area.
- Close the safety door.
- Initiate the auto-focus function (e.g., via voice command "Focus" or touch screen button) for high-speed automatic precision focus.
5. Starting the Laser Process
Once focused, initiate the laser process (e.g., via voice command "Start" or touch screen button). The machine will perform the selected operation, such as separating the screen or back cover. The process is designed for easy separation without requiring wire guides.
Maintenance
1. Activated Carbon Filter Maintenance
The machine is equipped with a multi-layer activated carbon filtration exhaust system to effectively adsorb harmful gases. Regularly check and replace the activated carbon filters as needed to maintain optimal air quality and machine performance.
2. General Cleaning
Keep the work area and exterior of the machine clean. Use a soft, dry cloth for cleaning. Avoid using abrasive cleaners or solvents that could damage the machine's surfaces or internal components.
3. Laser Lens Cleaning
Periodically inspect the laser lens for dust or debris. Clean gently with a specialized lens cleaning solution and a lint-free cloth to ensure clear laser output and marking accuracy.
Troubleshooting
- Machine not powering on: Check power cable connection and ensure the power switch is ON. Verify the power outlet is functional.
- Laser not firing: Ensure the safety door is fully closed. Check if the auto-focus process completed successfully. Verify that the correct operation mode and blueprint are selected.
- Poor marking quality: Clean the laser lens. Ensure the workpiece is properly focused. Check the material settings and adjust laser parameters if necessary.
- Voice control not responding: Ensure you are speaking clearly and within range of the microphone. Check the voice control settings in the software.
- Touch screen unresponsive: Restart the machine. If the issue persists, try using the external mouse and keyboard.
For persistent issues, please contact customer support.
Specifications
| Feature | Specification |
|---|---|
| Model Number | 958ZU |
| Laser Power | 4W |
| Working Range | 180 x 180 mm |
| Screen Size | 215 x 135 mm |
| Product Dimensions (L x W x H) | 450 x 300 x 565 mm |
| Product Weight | 35 kg |
| Laser Wavelength | 355 nm |
| Marking Speed | ≤7000 mm/s |
| Marking Accuracy | ≤0.1 mm |
| Marking Depth | ±0.2 mm |
| Voltage | 110~220V |
| Material Compatibility | Metal, Plastic, Glass, Silicone Products, Ceramics, Jade, various ornaments |
| Pieces Included | 1 (Machine) |
| Origin | Mainland China |
| Package Dimensions (L x W x H) | 67 x 33 x 65 cm |
| Package Weight | 42 kg |
User Tips
- Utilize the voice control feature to streamline repetitive tasks and improve workflow efficiency.
- Familiarize yourself with the extensive drawing library to quickly find and apply precise patterns for various phone models.
- Always perform a test run on a scrap piece of similar material before working on a valuable item to ensure correct settings and desired results.
- Keep the work area clear of any flammable materials.
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official TBK product documentation or contact your vendor. Keep your purchase receipt as proof of purchase.
