HTRC C35A

Contents

HTRC C35A Smart Battery Charger Instruction Manual

Model: C35A

1. Introduction

The HTRC C35A intelligent charger is an efficient, safe, and intelligent charging device designed for a wide range of batteries. It is suitable for 6V, 12V, and 24V battery types, including lead-acid batteries (AGM, GEL, EFB, MF, FLOODED, VRLA, SLA, WET), lithium batteries, and lithium iron phosphate (LiFePO4) batteries. This charger utilizes advanced smart charging technology to ensure quick and effective charging while protecting the battery and extending its overall lifespan.

Key features include:

  • Efficient Charging: High-frequency charging technology significantly shortens charging time and improves efficiency, preventing battery damage from overcharging.
  • Intelligent Control: Automatically identifies battery type and status, adjusting charging parameters to prevent overcharge and undercharge.
  • Multiple Protection: Incorporates overcharge, overcurrent, short circuit, and reverse connection protection for a safe charging process.
  • Portable Design: Compact and easy to carry for various charging needs.

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always observe the following safety precautions when using the charger:

  • Read all instructions before use.
  • Ensure adequate ventilation during charging to prevent gas buildup.
  • Do not expose the charger to rain or moisture.
  • Avoid charging frozen or damaged batteries.
  • Always connect the charger to the battery before plugging it into a power outlet.
  • Disconnect the power supply before disconnecting the battery.
  • Keep out of reach of children.
  • Do not attempt to open or modify the charger.

3. Product Overview

3.1 Package Contents

The HTRC C35A Smart Battery Charger package typically includes:

  • 1 x HTRC C35A Smart Battery Charger
  • 1 x Power Cable (Length: 200 cm / 78.74 inches)
  • 1 x Alligator Clips (Length: 100 cm / 39.37 inches)
  • 1 x Instruction Manual
Contents of the HTRC C35A Smart Battery Charger box, including the charger, power cable, alligator clips, and manual.
Figure 1: What's in the Box?

3.2 Charger Features and Display Indicators

The C35A charger features a clear digital display and intuitive controls:

Front view of the HTRC C35A Smart Battery Charger display, showing voltage, temperature, current, battery percentage, and mode indicators.
Figure 2: Charger Display and Controls
  1. Battery voltage indicator during charging
  2. Winter mode indicator (lights up when external temperature is below 10°C)
  3. Summer mode indicator (lights up when external temperature is higher than 28°C)
  4. Low current charging mode indicator (6V 2A, 12V 3A, 24V 5A)
  5. Medium current charging mode indicator (6V 5A, 12V 20A, 24V 10A)
  6. High current charging mode indicator (6V 10A, 12V 35A, 24V 18A)
  7. Repair mode indicator
  8. Charging saturation state (battery percentage)
  9. Mode selection button
Image showing the portable storage design of the HTRC C35A charger, with a handle and clips on both sides for cable management.
Figure 3: Portable Storage Design

The charger features a hand-held design with a harness wrap-around for power cords and clips on both sides for convenient storage.

4. Specifications

Feature Specification
Brand Name HTRC
Model C35A
Item Weight About 1.75kg
AC Input Voltage 100V-240V 50/60Hz
Input Power (with Load) Max 480W
Output Voltage 6V/12V/24V
Output Current 6V Max 10A / 12V Max 35A / 24V Max 18A
Minimum Start Volt 2V
Compatible Battery Types Lithium, LiFePO4, Lead-acid (AGM, GEL, EFB, MF, FLOODED, VRLA, SLA, WET, etc.)
Low Current Charging Mode 6V 2A, 12V 3A, 24V 5A
Medium Current Charging Mode 6V 5A, 12V 20A, 24V 10A
High Current Charging Mode 6V 10A, 12V 35A, 24V 18A
Dimensions 230mm x 150mm x 115mm
Image showing various battery types compatible with the HTRC C35A charger, including 6V GEL, 12V AGM, 12V Deep Cycle, and 24V Lithium LiFePO4 batteries.
Figure 4: Compatible Battery Types
Image illustrating the HTRC C35A battery charger's compatibility with various vehicles such as cars, boats, RVs, motorboats, motorcycles, and trucks.
Figure 5: Vehicle Compatibility

5. Setup

  1. Unpack: Carefully remove the charger and all accessories from the packaging. Inspect for any damage.
  2. Connect to Power: Plug the power cable into the charger and then into a standard AC power outlet (100-240V~50/60Hz).
  3. Connect to Battery:
    • Ensure the charger is unplugged from the AC outlet before connecting to the battery.
    • Connect the red (+) alligator clip to the positive (+) terminal of the battery.
    • Connect the black (-) alligator clip to the negative (-) terminal of the battery.
    • Ensure connections are secure and free from corrosion.
Image showing the HTRC C35A charger connected to a car battery with red and black alligator clips, ready for charging.
Figure 6: Charger Connected to Battery

6. Operating Instructions

6.1 Starting the Charging Process

  1. After connecting the charger to the battery and power outlet as described in Section 5, the charger will automatically identify the battery voltage (6V, 12V, or 24V).
  2. Press the Mode selection button (labeled '9' in Figure 2) to cycle through the available charging modes: Low, Medium, High, and Repair. Choose the mode appropriate for your battery's condition and capacity.
  3. The charger will automatically begin the charging process according to the selected mode and battery type. The display will show charging status, voltage, and battery saturation.
  4. The charger automatically detects ambient temperature and activates Winter mode (below 10°C) or Summer mode (above 28°C) as needed.
  5. Once charging is complete, the charger will automatically stop. Disconnect the power cable from the AC outlet first, then disconnect the alligator clips from the battery terminals.

6.2 Charging Modes Explained

Diagram illustrating the three current regulation modes (Low, Medium, High) and Repair mode for the HTRC C35A charger, with recommended battery types for each.
Figure 7: Current Regulation and Repair Modes
  • Low Mode (6V 2A, 12V 3A, 24V 5A): Suitable for various types of motorcycle lead-acid batteries and small capacity batteries.
  • Medium Mode (6V 5A, 12V 20A, 24V 10A): Ideal for dry batteries, wet battery lead-acid, maintenance-free batteries, and deep cycle batteries.
  • High Mode (6V 10A, 12V 35A, 24V 18A): Designed for large capacity batteries, offering faster charging.
  • Repair Mode: Used for battery activation and addressing issues like inability to charge or high internal resistance, often found in deeply discharged or sulfated batteries.

6.3 9-Stage Smart Charging Process

The C35A charger employs a sophisticated 9-stage charging algorithm for optimal battery health and efficiency:

Diagram illustrating the 9-stage smart charging process of the HTRC C35A charger, including desulfation, soft start, bulk, absorption, trickle, battery test, recondition, float, and small current maintenance.
Figure 8: 9-Stage Smart Charging Process
  1. Battery desulfation
  2. Soft start charging
  3. Bulk charging
  4. Absorption charging
  5. Trickle charging
  6. Battery test
  7. Recondition charging
  8. Float & maintenance charging
  9. Small current to maintain charging

7. Maintenance

  • Keep the charger clean and free from dust and debris.
  • Store the charger in a dry, cool place when not in use.
  • Regularly inspect the power cable and alligator clips for any signs of damage (cuts, fraying, corrosion). Replace if damaged.
  • Do not immerse the charger in water or any other liquid.

8. Troubleshooting

  • Charger does not turn on: Ensure the power cable is securely plugged into both the charger and a live AC outlet. Check the outlet with another device.
  • Charger not charging: Verify that the alligator clips are correctly and securely connected to the battery terminals (red to positive, black to negative). Ensure the battery voltage is above 2V, as the charger requires a minimum voltage to initiate charging.
  • Charging is slow: Confirm that the selected charging mode (Low, Medium, High) is appropriate for your battery's capacity and type. Larger batteries will charge slower on lower current modes.
  • Error message on display: Refer to the specific error code (if any) displayed on the screen. Common issues include reverse polarity (clips connected incorrectly) or a severely damaged battery.
  • Battery not holding charge after charging: This may indicate a problem with the battery itself, such as sulfation or internal damage. Try using the 'Repair' mode if applicable, but if the issue persists, the battery may need replacement.

9. User Tips

  • For optimal battery longevity, avoid letting your battery completely discharge. Regular maintenance charging can significantly extend battery life.
  • Always ensure good ventilation in the charging area, especially when charging lead-acid batteries, as they can emit hydrogen gas.
  • If you have multiple batteries of different types or voltages, double-check your connections and selected mode before starting to charge to prevent damage.
  • The 'Repair' mode can be very effective for older or deeply discharged lead-acid batteries, but it may not revive all batteries.

10. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or the manufacturer at the time of purchase. If you encounter any issues or require technical assistance, please contact the customer support of your seller or the HTRC service center.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.