1. Introduction
The Hantek DSO5072P is a high-performance digital storage oscilloscope designed for a wide range of electrical measurement and analysis tasks. Featuring a 70MHz bandwidth, 2 channels, and a 1GSa/s real-time sample rate, it provides accurate and reliable waveform capture and analysis. Its large 7-inch color display and extensive measurement functions make it an essential tool for engineers, technicians, and hobbyists.

Figure 1: Front view of the Hantek DSO5072P Oscilloscope
2. Setup
2.1 Package Contents
Before starting, verify that all items are present in the package:
- 1 x Hantek DSO5072P Oscilloscope
- 2 x Oscilloscope Probes
- 1 x USB Cable
- 1 x Power Cable
- 1 x CD & Manual

Figure 2: Oscilloscope with its packaging and included accessories
2.2 Connecting Power
- Ensure the oscilloscope is placed on a stable, flat surface with adequate ventilation.
- Connect the provided power cable to the power input port on the rear panel of the oscilloscope.
- Plug the other end of the power cable into a suitable AC power outlet.

Figure 3: Rear view of the oscilloscope, showing power input and ventilation
2.3 Connecting Probes
- Connect the BNC connector of the oscilloscope probe to the CH1 or CH2 input on the front panel.
- Ensure the probe is securely twisted into place.
- Attach the probe's ground clip to the circuit's ground point.
- Connect the probe tip to the test point in your circuit.
2.4 Initial Power-On
Press the power button on the front panel to turn on the oscilloscope. The device will perform a self-test and display the main waveform interface.
3. Operating Instructions
3.1 Basic Controls
Familiarize yourself with the front panel controls for adjusting vertical (VOLTS/DIV), horizontal (TIME/DIV), and trigger settings. Use the menu buttons and rotary knobs to navigate and select options on the 7-inch WVGA (800x480) color display.
3.2 Waveform Acquisition and Display
Adjust the VOLTS/DIV knob for each channel to set the vertical scale and the TIME/DIV knob to set the horizontal time scale. Use the trigger controls (Edge, Video, Pulse, Slope, Over time, Alternative) to stabilize the waveform display. The oscilloscope supports a record length of up to 40K points for detailed waveform capture.

Figure 4: Displaying various waveform examples on the oscilloscope screen

Figure 5: More examples of complex waveforms and measurements on the oscilloscope display
3.3 Measurement Functions
The DSO5072P offers multiple automatic measurements and cursor measurements:
- Automatic Measurements: Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF.
- Cursor Measurements: Voltage difference (ΔV), Time difference (ΔT), and Reciprocal of ΔT (1/ΔT).
3.4 Math Functions
Perform waveform calculations using built-in math functions: Addition (+), Subtraction (-), Multiplication (x), Division (÷), and Fast Fourier Transform (FFT).
3.5 USB Connectivity and PC Software
The oscilloscope features USB host and device connectivity. You can connect a USB drive to save waveform data or connect the oscilloscope to a PC for real-time analysis using the provided software.

Figure 6: Illustrates connecting a USB drive to the oscilloscope for data storage
Video 1: A video showcasing the Hantek DSO5072P oscilloscope and its features.
4. Maintenance
4.1 Cleaning
To clean the oscilloscope, use a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the casing or display. Ensure the device is powered off and unplugged before cleaning.
4.2 Storage
When not in use, store the oscilloscope in a dry, dust-free environment. Avoid extreme temperatures and direct sunlight. Disconnect all probes and cables before storage.
4.3 Battery (if applicable)
The DSO5072P does not include a battery. If using an external power source, ensure it meets the device's power requirements.
5. Troubleshooting
This section addresses common issues you might encounter with your Hantek DSO5072P oscilloscope.
5.1 No Display After Power On
- Check if the power cable is securely connected to both the oscilloscope and the power outlet.
- Verify that the power outlet is functional.
- Ensure the power button has been pressed firmly.
5.2 Unstable Waveform
- Adjust the trigger level and trigger mode settings to match the input signal characteristics.
- Ensure the probe's ground clip is properly connected to the circuit's ground.
- Check the probe compensation.
5.3 Incorrect Measurements
- Verify the probe attenuation setting on the oscilloscope matches the physical probe setting (e.g., 1X, 10X).
- Ensure the input signal is within the oscilloscope's voltage range.
- Perform a self-calibration if available in the device menu.
5.4 USB Data Transfer Issues
- Ensure the USB cable is correctly connected to both the oscilloscope and the PC.
- Check if the PC software is installed correctly and recognizes the device.
- Try a different USB port or cable.
6. Specifications
| Feature | Specification |
|---|---|
| Model | DSO5072P |
| Bandwidth | 70MHz |
| Channels | 2 |
| Real-Time Sample Rate | 1GSa/s |
| Equivalent Sample Rate | 25GSa/s |
| Record Length | 40K |
| Rise Time | 5ns |
| Time Base Accuracy | ±50ppm |
| Time Base Range | 4ns/div - 40s/div |
| Input Impedance | 1MΩ |
| VOLTS/DIV Range | 2mV/div - 5V/div |
| A/D Converter | 8 bit |
| Position Range | ±50V(5V/div), ±40V(2V/div~500mV/div), ±2V(200mV/div~50mV/div), ±400mV(20mV/div~2mV/div) |
| DC Gain Accuracy | ±3% (5V/div to 10mV/div), ±4% (5mV/div to 2mV/div) |
| Bandwidth Limit | 20MHz |
| Trigger Types | Edge, Video, Pulse, Slope, Over time, Alternative |
| Trigger Source | CH1, CH2, EXT, EXT/5, AC Line |
| Math Functions | +,-,x,÷,FFT |
| Display | 7" TFT 16K Color LCD, 800*480 dots |
| Size | 313mm x 108mm x 142mm |
| Weight | 2.08KG |
| Battery Included | No |
| Battery Demountable | Yes |
| DIY Supplies | Electrical |
| Certification | CE |
7. User Tips
Based on general oscilloscope usage and common user inquiries, here are some tips for optimizing your experience with the Hantek DSO5072P:
- Probe Compensation: Always perform probe compensation before taking critical measurements to ensure accurate readings. This usually involves connecting the probe to a dedicated compensation output on the oscilloscope and adjusting the probe's trimmer until a perfect square wave is displayed.
- Grounding: Proper grounding is crucial for accurate measurements and user safety. Always connect the oscilloscope's ground lead to the circuit's ground reference.
- Signal Integrity: Keep probe leads as short as possible and avoid coiling them to minimize noise and interference, especially for high-frequency signals.
- Firmware Updates: Check the manufacturer's website periodically for firmware updates, which may offer new features, performance improvements, or bug fixes.
- Environmental Conditions: Operate the oscilloscope within its specified environmental conditions (temperature, humidity) to ensure optimal performance and longevity.
8. Warranty and Support
8.1 Warranty Information
The Hantek DSO5072P Digital Storage Oscilloscope comes with a 1-year after-sales service from the date of purchase. This warranty covers manufacturing defects and ensures that the product will be working correctly upon delivery.
8.2 Technical Support
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact the seller or manufacturer's customer support. Have your product model and purchase details ready to expedite the support process.