BAOFENG 5RH PRO V2

Contents

Baofeng 5RH PRO V2 GPS Walkie Talkie User Manual

Model: 5RH PRO V2

Introduction

Thank you for purchasing the Baofeng 5RH PRO V2 GPS Walkie Talkie. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communication. Please read this manual carefully to ensure maximum performance and safe operation of your device.

The BF-5RH series products are available in M version and L version. The M version supports AM108-136, Police350-390MHz scanning reception, and voice scrambling functions. The L version does not support AM108-136, Police350-390MHz scanning reception, and voice scrambling functions, and lacks the voice scrambling option in the function menu.

1. Safety Warnings and Regulations

1.1 General Safety Instructions

  • Do not operate the product in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials. Only approved Ex-protection models are allowed in such locations, and any assembly or disassembly is strictly prohibited.
  • Do not operate the product near any blasting area.
  • Do not operate the product near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate the product in any area where wireless communication equipment is prohibited.
  • Do not use the radio with a damaged antenna. If a damaged antenna contacts the skin, a minor burn may result. Contact your local dealer for a replacement antenna.

1.2 RF Exposure Compliance

Hand-Held Operation (Held-to-Face): This device was evaluated for typical hand-held operations with a 1-inch spacing from the front of the radio. For compliance with FCC RF exposure requirements, hold the radio 1 inch from your face.

Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; additional or optional accessories are not required for compliance. Third-party accessories (unless approved by the manufacturer) should be avoided as they might not comply with FCC RF exposure guidelines.

1.3 Precautions for Batteries

Charging Prohibitions:

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not charge a wet battery. Dry it with a soft, clean cloth before charging.
  • Do not charge a battery suffering deformation, leakage, or overheating.
  • Do not charge your battery with an unauthorized charger.
  • Do not charge your battery in a location with strong radiation.
  • Overcharging is prohibited as it may shorten battery life.

Maintenance Instructions:

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
  • Charge the battery between 5°C and 40°C (40°F - 105°F). Charging outside this range may prevent full charge or reduce battery life.
  • Turn off the radio when charging a battery attached to the product to ensure a full charge.
  • Do not remove the battery or unplug the power cord during charging until the green light is on.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heating sources.
  • Do not squeeze, penetrate, or remove the housing of the battery.

Transportation Instructions:

  • Damaged batteries must not be transported.
  • To avoid short circuits, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  • The radio must be switched off and secured against switch-on if the battery is attached.
  • The content of the shipment must be declared in shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for local regulations.

1.4 Radio Maintenance

  • Do not attempt to open the radio for any reason. Unauthorized opening voids the warranty.
  • Do not store the radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
  • Do not transmit without an antenna.

2. Main Features

  • Frequency Range: FM radio 76-108 MHz; AM aviation frequency band: 108-136MHz (RX); VHF1: 144-148MHz (RX&TX); VHF2: 200-260MHz (RX); UHF1: 430-440MHz (RX&TX); UHF2: 350-390MHz (RX).
  • Output Power: 5W-10W.
  • Channels: 640 Storage Channels (up to 999 memory channels).
  • Display: 1.77" TFT large color screen, full keyboard, fully open menu operation.
  • Charging: USB-C Charge, Type-C Charging.
  • Waterproof: IP45.
  • GPS Function: Location Sharing and Acquisition APRS Function (compatible with YAESU - Transmit Only). Note: In GPS mode, you can only view location information and cannot make normal calls. Voice intercom must exit GPS mode to proceed.
  • Wireless Copy Frequency: One touch search frequency, easy pairing and grouping (copying channel configuration parameters).
  • Scanning: Channel scan, frequency scan, and three scan and recovery methods: TO, CO, and SE.
  • VOX: Voice Activated Transmit (hands-free conversations).
  • Alarm Function: Fallback Alarm (sends alarm code/tone if radio falls and not picked up within 5 seconds).
  • Power: High or low power selectable.
  • Repeater Offset: Programmable repeater offset.
  • Timer: Transmission time-out timer, Stopwatch function.
  • LED Flashlight: Built-in LED flashlight.
  • Roger Beep: End of transmission tone.
  • Weather Radio: Support NOAA weather reception function in the United States and Canada.
  • Dual Watch: Dual watch / Dual reception/ Dual-band handheld transceiver.
  • Squelch: Ten (10) levels of Squelch adjustment.
  • Accessory Port: Two (2) pins for Kenwood accessory port.
  • Analog Signaling: DTMF, 2TONE, 5TONE, BDC1200 Codecs.
Baofeng 5RH PRO V2 GPS Walkie Talkie with key features highlighted: 10W True Max Distance, Multi-Band, GPS, 999 Channels, Type-C Charger, 100% Original.
Overview of Baofeng 5RH PRO V2 GPS Walkie Talkie features.
Summary of Baofeng 5RH PRO features including GPS Function, Multi-Bands, 1.77 inch TFT Large Screen, Type-C Charger, 640 Memory Channels, Wireless Copy Frequency, Fallback Alarm, Analog signaling DTMF, 2TONE, 5TONE BDC1200 codecs.
Key features of the 5RH PRO model.

3. Package Contents

The package should contain the following items. If any item is missing, please contact your dealer.

  • 1 x Radio
  • 1 x Li-Ion battery pack
  • 1 x Fast desktop charger
  • 1 x Antenna
  • 1 x Belt clip
  • 1 x User's manual (PDF)
  • 1 x Lanyard
  • 1 x Clip
  • 1 x Box
  • 1 x Type-C Charging Cable
Image showing the contents of the 5RH PRO package: Antenna, User's manual, Lanyard, Clip, Box, Battery, and Type-C Charging cable.
Contents included in the 5RH PRO package.

4. Radio Overview

4.1 Buttons and Controls

Diagram showing the front, side, and back views of the Baofeng 5RH PRO radio with numbered parts.
Front, side, and back views of the radio.
  1. Power/Volume knob
  2. SK1- Broadcast FM and Alarm key
  3. PTT key
  4. VFO/MR mode key
  5. Status LED
  6. SK2-Flashlight and Monitor key
  7. A / B select key
  8. Menu key
  9. Numeric keypad
  10. Antenna jack
  11. LED flashlight
  12. Color LCD
  13. Accessory jack
  14. Speaker and microphone
  15. One-Touch search key
  16. Exit key
  17. Up or Down navigation keys
  18. Type-C charging port
  19. Type-C charging indicator
  20. Battery release latch

4.2 LCD Display Icons

IconDescription
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
DDCS enabled
CCTCSS enabled
+Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX.
-Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX.
DDual watch enabled
.Keypad lock enabled
VOX enabled
NNarrowband enabled
Battery level indicator
RReverse function enabled
Indicates active band or channel
SCRThe voice scramble function has been activated

Battery Level Indicator: When the battery level indicator shows a depleted icon, the radio will start beeping periodically, flash the backlight, and announce "Low Voltage" if voice prompts are enabled. This indicates the need for charging or battery replacement.

4.3 Status Indications

LED IndicatorRadio Status
Constant RedTransmitting
Constant GreenReceiving

5. Setup and Installation

5.1 Installing/Removing the Antenna

  1. Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  2. Removing: Turn the antenna counter-clockwise to remove it.

5.2 Installing the Belt Clip

  1. At the back of the radio, remove the two parallel screws mounted above the battery. Thread them through the holes on the belt clip as you screw them back into the radio body.
  2. To remove the belt clip, unscrew counter-clockwise.

5.3 Installing/Removing the Battery Pack

Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

  1. Installing: Align the battery in parallel with the radio body, with the lower edge of the battery about 1-2cm below the edge of the radio. Once aligned with the guide-rails, slide the battery upward until you hear a click as it locks in place.
  2. Removing: Press the battery release above the battery pack, then slide the battery downward.

5.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram showing how to connect an external speaker/microphone to the radio's accessory jack.
Connection diagram for external speaker/microphone.

6. Charging the Battery

6.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; charge it before use. For best performance, fully charge/discharge the battery two or three times before regular use. If operating time decreases after full charge, replace the battery pack.

6.2 Charger Supplied

Use only the specified charger provided by Baofeng. Other chargers may cause explosion or personal injury. Charge the battery when the radio displays low battery with a voice prompt.

6.3 How to Charge

  1. Plug the AC adaptor into the AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange, then is ready to charge.
  2. Plug the battery or the radio into the charger. Ensure good contact with charging terminals. The indicator light turns red, indicating charging has begun.
  3. A full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete.
  4. Remove the battery or radio unit from the socket.

Note: If the radio is powered on during charging, the indicator lamp will not turn green to show full charge. The radio consumes energy when powered on, preventing the charger from detecting the correct battery voltage. It will charge in constant voltage mode and may not indicate correctly when fully charged. It is recommended to power off the radio while charging.

6.4 Using the Type-C USB Charger

The Type-C USB port allows convenient charging of your Li-ion battery pack.

  1. Make sure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall outlet.
  3. An empty battery will be fully charged in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging progress.
Image showing the Type-C charging port on the radio and various charging methods: Wall Charging, Car charging, Power Bank, USB Plug, Laptop.
Type-C charging options for convenience.

6.5 LED Indicator for Charging

StatusLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

Note: "Trouble" indicates the battery is too warm, short-circuited, or the charger is short-circuited.

6.6 How to Store the Battery

  • Store the battery at approximately 80% discharged.
  • Keep it in a low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.
  • Do not store the battery in unsafe surroundings, as a short may cause an explosion.

7. Basic Operations

7.1 Power On/Off

  • To turn on: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will emit a double beep and display a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • To turn off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

7.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease. Use the monitor function (SK2 key) to adjust volume to an un-squelched static for easier setting.

7.3 Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The selected display's frequency or channel becomes the active listening and transmit frequency/channel. To save frequencies to channel memory, you must be on the A display.

7.4 VFO/Channel Switch

Press the [VFO/MR] key to switch between Frequency (VFO) mode and Channel (MR) mode.

  • In Channel (MR) mode, the channel number is displayed on the right.
  • In Frequency (VFO) mode, 'VFO' is displayed on the right.

7.5 Frequency (VFO) Mode

In VFO mode, navigate up/down the band using the ▲ or ▼ keys, or input frequencies directly using the numeric keypad (e.g., for 436.61250 MHz, enter [4][3][6][6][1][2][5][0]).

Warning: Transmitting on unauthorized frequencies is illegal. Always ensure you have proper authorization.

7.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use. Navigate channels using the ▲ or ▼ keys or the encoder, or input channel numbers directly (e.g., for channel 12, input [0][1][2]).

7.7 Making a Call

  • Channel Mode Call: Select a channel, hold down the [PTT] key to transmit. Speak into the microphone. The red LED will be on.
  • Frequency Mode Call: Switch to frequency mode, input the working frequency, hold down the [PTT] key to transmit. The red LED will be on.
  • Receive a Call: Release the [PTT] key. The green LED will be on when receiving.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

7.8 Using the Flashlight

Press [SK2] key momentarily to turn on the LED flashlight. Another momentary press will flash the LED. A third press turns it off.

7.9 Emergency Alert

To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and flash the flashlight. Press [SK1] again to exit. Use only in actual emergencies.

7.10 FM Radio (FM)

The radio receives FM radio from 65-108MHz.

  1. Press [SK1] key to turn on the radio.
  2. Select the desired frequency with ▲ or ▼ keys or input directly. Press #z to automatically search for stations.
  3. Press [SK1] key to exit FM radio.

Note: If a signal is received on the active frequency/channel while listening to FM, the radio will switch to that frequency for communication and return to FM mode when the signal disappears.

7.11 Monitor

Press and hold [SK2] key to enter Monitor mode, allowing you to hear weak signals by opening the squelch. Release [SK2] to exit.

7.12 Keypad Lock

To enable/disable, press and hold the * key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds from the menu.

7.13 Frequency Reversal

A short momentary press of the * key enables the reverse function, swapping transmit and receive frequencies. The LCD will display "R" when active.

7.14 TX Repeaters Tone

Press [PTT] + [SK2] key to send a 1750Hz repeater tone. This works even if the keypad is locked.

Two images of the radio display during one-touch frequency search. The left shows 'SEARCH UHF SEARCH...' and the right shows a found frequency '144.12500' with CTCSS/DCS NONE.
Radio display during one-touch frequency search.
  1. Press and hold the # key. The screen will display "SEARCH SEARCH...".
  2. If a strong, stable signal is received, the frequency and any CTCSS/DCS values will be displayed.
  3. Press the MENU key to save the search frequency and CTCSS/DCS to a channel.

Note: During search, press #z to switch between UHF or VHF bands.

7.16 Weather Radio/Scan Weather Channel

The radio has a NOAA Weather Radio function for receiving weather reports and a Weather Scan function for scanning 10 NOAA channels.

  1. To turn on NOAA Weather Scan, press the [0sQL] key for 3 seconds. The icon appears, and the radio enters Weather band mode.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels.
  3. After stopping the scan, you can manually select weather channels using the ▲ or ▼ keys.
  4. To exit Weather Radio broadcast mode, press the EXIT key or [PTT] key.
Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

Note: Weather Channels Wx 1 Thru 10 are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

8. Advanced Features

8.1 Working the Menu System

For a complete reference on available menu items and parameters, see Appendix B, Menu definitions. If your radio is set to Memory (MR) mode, certain menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.

Basic Use with Arrow Keys:

  1. Press the MENU key to enter the menu.
  2. Use the ▲/▼ keys to navigate between menu items.
  3. Press MENU again to select the desired menu item.
  4. Use the ▲/▼ keys to select the desired parameter.
  5. To confirm your selection, press MENU. To cancel changes, press EXIT.
  6. To exit the menu at any time, press EXIT.

Using Short-Cuts: Every menu item has a numerical value for direct access. The menu is organized with common functions on top. Parameters also have associated numbers.

  1. Press the MENU key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. Press the MENU key to enter the menu item.
  4. For parameters, use arrow keys or numerical keypad.
  5. To confirm, press MENU. To cancel, press EXIT.
  6. To exit the menu, press EXIT.

8.2 Scanning

The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited while scanning.

To enable the scanner, press and hold the #z key for about two seconds. Press and hold the #z key again to exit scanning mode.

Image showing the radio display with 'Scan' menu options: Freq Ranger, Chan Ranger, Scan Mode, Scan SubCode.
Scanner function menu on the radio display.

Scanning Modes:

  • Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes when the signal disappears.
  • Search Operation (SE): Scanner stops on a signal. To resume, press and hold #z again.

Frequency Scanning: In frequency mode, press #z for more than 2 seconds. Change direction with ▲/▼ keys. Press #z to stop.

Channel Scanning: In channels mode, press #z for more than 2 seconds. Change direction with ▲/▼ keys. Press #z to stop.

Scan CTCSS: In standby mode, press MENU, then [1][4]. Press MENU to start scanning CTCSS tones. Not active in Channel mode.

Scan DCS: In standby mode, press MENU, then [1][5]. Press MENU to start scanning DCS codes. Not active in Channel mode.

8.3 Manual Programming (Channels Memory)

The radio features 999 memory channels. Each can hold receive/transmit frequencies, power, signaling, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Frequency Mode vs. Channel Mode: Use [VFO/MR] key to switch. VFO mode is used for temporary frequency assignments and programming channels into memory.

Example 1: Programming a Channel Repeater Offset with CTCSS Tone (Channel 10)

  1. Press MENU.
  2. Press [VFO/MR] to set to VFO mode.
  3. Enter [3][1] then [1][0] to delete prior data in channel 10.
  4. Enter [1][2] then 123.0 to select desired TX encode tone.
  5. Enter RX frequency (e.g., 43255000).
  6. Enter [3][0] then [1][0] to enter desired channel (10). RX has been added.
  7. Enter TX frequency (e.g., 43755000).
  8. Enter [3][0] then [1][0] to enter the same channel (10). TX has been added.
  9. Press [VFO/MR] to return to MR mode.

Example 2: Programming a Simplex Channel with CTCSS Tone (Channel 10)

  1. Press MENU.
  2. Press [VFO/MR] to set to VFO mode.

8.4 Repeaters Programming

This assumes you know the repeater's transmit/receive frequencies and are authorized to use it.

  1. Press [VFO/MR] to set to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (receiving) frequency.
  3. Press MENU.
  4. Enter [2][9] for frequency offset.
  5. Press MENU to select.
  6. Use the numerical keypad to enter the specified frequency offset.
  7. Press MENU to confirm and save.
  8. Enter [2][8] for offset direction.
  9. Use ▲/▼ keys to select + (positive) or - (negative) offset.
  10. Press MENU to confirm and save.
  11. Optional: Save to memory (see Manual Programming) or set up CTCSS.
  12. Press EXIT to exit the menu.

If experiencing problems, check settings or contact the radio system administrator.

8.5 VOX (Voice Activated Transmit)

This function allows hands-free conversations. In standby mode, press MENU then 7. The screen displays "VOX". Press MENU to enter. Use ▲/▼ keys to turn off VOX or select levels (1-10). Press MENU to confirm. Press EXIT to return to standby. Level 1 is least sensitive, level 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.

Image of a person cycling with a Baofeng radio, highlighting the VOX Hands-free feature. Text says 'VOX levels are adjustable and provide convenience for special occasions.'
VOX Hands-free for convenient communication.

8.6 Dual Watch

This feature allows monitoring two channels simultaneously. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.

Enabling/Disabling Dual Watch:

  1. Press MENU.
  2. Enter 7 on the numeric keypad for Dual Watch.
  3. Press MENU to select.
  4. Use ▲/▼ keys to enable or disable.
  5. Press MENU to confirm.
  6. Press EXIT to exit.

8.7 Stopwatch Timer

In standby mode, press MENU then 44. The screen displays "STOP WATCH". Press MENU to enter. Use ▲/▼ keys to enable (ON), then press MENU to confirm. Press EXIT to return to standby.

Using the Stopwatch: When ON, press MENU to start counting. Press MENU again to restart counting. To exit, stop counting first, then press EXIT.

8.8 Scrambler

The scrambler protects communications by voice inversion. In standby mode, press MENU then 45. The screen displays "SCRAMBLE". Press MENU to enter. Use ▲/▼ keys to select scramble mode (MODE1 to MODE3). The "SCR" icon appears on the display.

8.9 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals. It's used for automation systems and remote control, common in amateur radio repeaters.

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

The radio has full DTMF implementation, including A, B, C, and D codes. Numerical keys, *, and # correspond to DTMF codes. A, B, C, and D codes are on the ▲, ▼, and MENU keys respectively. To send DTMF codes, press the corresponding key(s) while holding down the PTT key. This works even with keypad lock enabled.

Image showing two Baofeng radios side-by-side, highlighting Analog signaling DTMF, 2TONE, 5TONE, BDC1200 Codecs.
Analog signaling features including DTMF.

8.10 Customization

The radio allows customization of visual and audible features.

  • Display Backlight (ABR) - MENU 7: In standby, press MENU then 7. Select ON/5sec/10sec/15sec/20sec.
  • Beep PROMPT (BEEP) - MENU 8: Enables/disables key press beep tone. In standby, press MENU then 8.
  • Voice Function (VOICE) - MENU 17: Enables/disables voice prompts. In standby, press MENU then 17.
  • Language (LANGUAGE) - MENU 18: Sets menu and prompt language (English/Chinese). In standby, press MENU then 18.
  • Working Mode (MDF-A) - MENU 24: Sets display mode (Frequency, Channel, Channel Name). In standby, press MENU then 24.
  • Roger Beep (ROGER) - MENU 36: Enables/disables end-of-transmission tone. In standby, press MENU then 36.
  • Power On Message (POWER ON MSG) - MENU 40: Customizes welcome message (VOLTAGE, MESSAGE, LOGO, MODEL NAME). In standby, press MENU then 40.
  • Power On Password (POWER ON PWD) - MENU 43: Enables/disables power-on password. In standby, press MENU then 43.

8.11 Reset - MENU 42

The transceiver has two reset modes:

  • Reset VFO: Resets all settings except channels to default. In standby, press MENU then 42. Select VFO.
  • Reset ALL: Resets all settings to default. In standby, press MENU then 42. Select ALL.

9. Troubleshooting Guide

PhenomenaAnalysisSolution
You cannot turn on the radio.Battery improperly installed, power run out, dirty/damaged contacts.Reattach/recharge/replace battery, clean contacts.
Weak or intermittent voice during receiving.Low battery, low volume, loose/incorrect antenna, blocked speaker.Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling, too far away.Verify TX/RX frequency/signaling, move closer.
You hear unknown voices or noise.Interrupted by other radios, analog mode with no signaling.Change frequency, adjust squelch, set signaling.
Unable to hear anyone due to too much noise/hiss.Too far away, unfavorable position (blocked by buildings/underground), external disturbance.Move closer, move to open area, restart radio, stay away from interference.
The radio keeps transmitting.VOX turned on, headset not installed.Turn off VOX, check headset.

Note: If these solutions do not resolve your problems, please contact your dealer for technical support.

10. Technical Specifications

CategorySpecification
Frequency RangeEurope: 144-146 & 430-440MHz (RX & TX)
Canada: 144-148 & 430-450MHz (TX)
Canada: 138-174 & 406-470MHz (RX)
Channel Spacing25.0KHz (Wide) / 12.5KHz (Narrow)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Transmission Current≤1600mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive Current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm

Note: All specifications may be modified without prior notice or liability.

The BF-5RH series products are divided into M version and L version. The M version supports AM108-136, Police350-390MHz scanning reception, and voice scrambling functions. The L version does not support AM108-136, Police350-390MHz scanning reception, and voice scrambling functions.

11. User Tips

  • Channel Name Programming: While the radio allows basic channel programming, for advanced features like programming channel names, it is often necessary to use dedicated programming software with a PC. This provides more flexibility and control over channel configurations.
  • GPS Functionality: Remember that in GPS mode, the radio primarily focuses on location information. For voice communication, you must exit GPS mode.
  • Battery Life: To maximize battery life, avoid overcharging and store the battery partially discharged in a cool, dry place.

12. Support and Warranty

Your Baofeng 5RH PRO V2 GPS Walkie Talkie is an electronic product of exact design and should be treated with care. For any issues not covered in the troubleshooting guide or for further technical assistance, please contact your authorized dealer or the manufacturer's support.

Unauthorized opening or modification of the transceiver will void the warranty.

13. Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.