BUNOEM Dual Motor 63x30 Height Adjustable Electric Standing Desk

Contents

BUNOEM Dual Motor 63x30 Height Adjustable Electric Standing Desk

Model: Dual Motor 63x30 Height Adjustable Electric Standing Desk

Introduction

Thank you for choosing the BUNOEM Dual Motor 63x30 Height Adjustable Electric Standing Desk. This desk is designed to enhance your workspace by allowing seamless transitions between sitting and standing positions, promoting better posture and increased productivity. Its robust dual-motor system ensures smooth, quiet, and stable height adjustments. This manual provides essential information for the setup, operation, maintenance, and troubleshooting of your new standing desk.

BUNOEM Electric Standing Desk in an office setting with multiple monitors
The BUNOEM Electric Standing Desk provides an ergonomic workspace.

Safety Information

  • Ensure all components are securely fastened before use.
  • Keep children and pets away from the desk during operation.
  • Do not overload the desk beyond its maximum weight capacity of 265 lbs.
  • Avoid placing liquids directly on the control panel or near electrical components.
  • If any unusual noise or movement occurs, discontinue use and consult the troubleshooting section.

Package Contents

Please verify that all parts are present before beginning assembly:

  • Desktop (Splice Board, Oak + White Top)
  • Desk Frame (White Frame)
  • Dual Motors
  • Control Panel with 4 Memory Buttons
  • Power Adapter and Cables
  • Assembly Hardware (screws, tools, etc.)
  • Instruction Manual (this document)

Setup and Assembly

The BUNOEM standing desk is designed for self-contained installation and is easy to assemble. Follow the instructions provided in the separate assembly guide (if included) or the general steps below.

  1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
  2. Assemble Desk Frame: Attach the legs to the crossbar and feet according to the diagrams. Ensure all screws are tightened securely.
  3. Install Dual Motors: Position and secure the dual motors within the frame structure.
  4. Attach Desktop: Carefully place the desktop onto the assembled frame and secure it using the provided screws.
  5. Connect Control Panel: Attach the control panel to the designated area on the desktop and connect its cable to the motor system.
  6. Cable Management: Utilize the two wire collection holes on the desktop to route and organize your cables, keeping your workspace tidy.
  7. Power Connection: Plug the power adapter into the desk and then into a suitable power outlet.
Diagram showing dual motors and frame structure for stability
The dual motor system provides stronger load capacity and stability.

Operating Instructions

Your BUNOEM standing desk features a powerful dual-motor lift system for quiet and quick height adjustments, along with intelligent memory functions.

Control panel with up/down arrows and memory presets 1, 2, 3, 4
Intelligent Memory Keypad for easy height adjustments.

Height Adjustment

  • Use the Up (▲) and Down (▼) arrows on the control panel to manually adjust the desk height.
  • The desk can be adjusted from a minimum height of 27 inches to a maximum height of 45 inches.
  • The telescoping legs ensure smooth and quiet height adjustment, with noise levels below 50dB.
Diagram showing height adjustment range from 27 to 45 inches with noise level indication
Quiet and smooth height adjustment from 27" to 45".

Memory Presets

The control panel features 4 programmable memory buttons (1, 2, 3, 4) to save your preferred sitting and standing heights.

  1. Set a Memory Position:
    • Adjust the desk to your desired height using the Up/Down arrows.
    • Press the 'M' button (or similar memory set button, if present, otherwise assume direct press).
    • Immediately press one of the number buttons (1, 2, 3, or 4) to save the current height to that preset. The LED display may flash to confirm.
  2. Recall a Memory Position:
    • Press the corresponding number button (1, 2, 3, or 4). The desk will automatically move to the saved height.

Anti-Collision Technology & Current Protection

  • The desk is equipped with anti-collision technology that accurately detects obstacles during height adjustment. If an obstacle is detected, the desk will automatically stop and reverse approximately 2cm (0.78 inches) to prevent damage.
  • Current protection function safeguards the motor system from electrical overloads.

Maintenance

  • Cleaning: The desktop is waterproof and wear-resistant. Wipe the desktop surface with a soft, damp cloth and mild detergent. Avoid abrasive cleaners or harsh chemicals.
  • Frame Care: Clean the metal frame with a dry or slightly damp cloth.
  • Cable Management: Periodically check and tidy up cables to prevent tangling or damage.
  • Inspection: Regularly inspect all screws and connections to ensure they remain tight. Tighten if necessary.

Troubleshooting

ProblemPossible CauseSolution
Desk does not move or respond to controls.Power cable disconnected, motor overload, or system error.
  • Check if the power cable is securely plugged into the desk and the wall outlet.
  • Unplug the desk for 10 minutes, then plug it back in to reset.
  • Perform a system reset (see below).
Desk stops moving unexpectedly.Anti-collision sensor triggered or weight overload.
  • Check for any obstacles in the desk's path.
  • Ensure the desk is not overloaded beyond 265 lbs.
  • Move the desk slightly in the opposite direction using the arrows, then try again.
Error code displayed on LED screen.System malfunction or sensor issue.
  • Reset Procedure: Press the Up (▲) and Down (▼) keys simultaneously for more than five seconds to reset the system.
  • If the error persists after resetting, contact customer support.
Desk movement is not smooth or is noisy.Uneven load, loose connections, or motor issue.
  • Ensure the weight on the desk is evenly distributed.
  • Check all assembly screws for tightness.
  • If noise exceeds 50dB or movement is consistently rough, contact customer support.

Specifications

FeatureDetail
Desktop Dimensions63 inches (Length) x 30 inches (Width)
Height Adjustment Range27 inches to 45 inches
Weight Capacity265 lbs
Motor TypeDual Motor
Noise Level< 50dB
Memory Presets4 programmable buttons
Safety FeaturesAnti-Collision Technology, Current Protection Function
Desktop MaterialEco-friendly Particle Board (Waterproof, Wear-resistant)
Frame MaterialHeavy-duty Powder-coated Steel
Installation MethodSelf-contained
High-concerned chemicalNone
OriginUS (Origin)
Diagram showing desk dimensions: 63 inches length, 30 inches width, 27 to 45 inches height, 265 lbs weight capacity
Key dimensions and weight capacity of the BUNOEM Standing Desk.

User Tips

  • Cable Management: Take advantage of the built-in wire collection holes to keep your workspace organized and free from clutter.
  • Regular Movement: To maximize the health benefits, try to alternate between sitting and standing positions throughout your workday.
  • Personalized Heights: Program your ideal sitting and standing heights into the memory presets for quick and easy transitions.
  • Monitor Setup: The spacious 63" x 30" desktop can comfortably accommodate multiple monitors and a laptop, allowing for a comprehensive workstation setup.

Warranty and Support

For warranty information, technical support, or any questions not covered in this manual, please contact BUNOEM customer service. Keep your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.