PowMr POW-Keeper Series

Contents

PowMr MPPT Solar Charger Controller User Manual

Models: POW-Keeper1220 (20A), POW-Keeper1230 (30A), POW-Keeper1240 (40A)

1. Introduction and Features

Thank you for choosing the PowMr MPPT Solar Charger Controller. This series utilizes advanced Maximum Power Point Tracking (MPPT) control algorithms to efficiently track the maximum power point of your PV array in any environment, significantly improving energy utilization in your solar system. The controller features a dual display function (LCD and optional Remote header) and a standard communication interface for extended application and comprehensive monitoring.

This controller series includes 20A, 30A, and 40A models, all offering high MPPT charging efficiency of 97% and a maximum charging current of 40A. It incorporates a three-stage charging algorithm to optimize battery performance and extend battery life. With a maximum PV input voltage of 100V, it is suitable for various 12V or 24V lithium-ion and lead-acid battery systems. The built-in DC output port delivers 30A of direct current, making it suitable for powering DC loads.

Key Features:

  • Advanced MPPT maximum power point tracking technology with tracking efficiency no less than 99.5%.
  • High conversion efficiency, reaching up to 97%.
  • Super-fast maximum power tracking speed.
  • Accurate identification and tracking of multi-wave peak maximum power points.
  • Reliable maximum input power for PV array to ensure equipment safety.
  • Wide PV array maximum power point operating voltage range.
  • 12V/24V automatic voltage identification.
  • LCD for dynamic display of operation data and working status.
  • Various load control modes: general mode, light control mode, dual time mode, pure charger mode, and timing mode.
  • Supports Seal, GEL, Flooded, LiFePO4, and Li(NiCoMn)O2 battery charging processes.
  • Battery temperature compensation function.
  • Power statistics recording function.
  • External display unit and other peripherals for real-time data view and parameter setting.

Kind Tip: The controller will initiate the PWM function at the High Voltage Disconnection (HVD) voltage point. This limits voltage rising to protect the battery.

Video: Overview of PowMr MPPT Solar Charger Controller features and models.

2. Product Appearance and Components

PowMr MPPT Solar Charger Controller front view with numbered components

Figure 1: Front view of the PowMr MPPT Solar Charger Controller with labeled components.

Table 1: Component Identification
No.ComponentDescription
①LCDLiquid Crystal Display for operational data.
②Temperature sensor interface (Selection)Port for connecting an external temperature sensor.
③Photovoltaic array terminalsTerminals for connecting solar panels (PV array).
④Battery terminalTerminals for connecting the battery.
⑤Load terminalTerminals for connecting DC loads.
⑥Menu ButtonUsed to navigate through display parameters.
⑦Set ButtonUsed to change and confirm parameter settings.
⑧USB outputDual USB ports for charging external devices.

NOTICE: If a remote temperature sensor is not connected, the controller will compensate charging parameters by 25°C for the battery temperature.

3. Setup and Installation

3.1 Safety Precautions

  • Ensure all connections are secure and correct before powering on.
  • Always connect the battery first, then the solar panel. Disconnect in reverse order.
  • Install the controller in a well-ventilated area, away from direct sunlight and heat sources.
  • Avoid installing in areas with flammable or explosive gases.
  • Use appropriate wire gauges for all connections to prevent overheating.

3.2 Wiring Instructions

Follow these steps for proper wiring:

  1. Open the Cover: First, open the cover of the controller to access the screw terminals. You may need to rotate a screw to release the cover.
  2. Wire the Battery: Connect the battery cables to the battery terminals (④) on the controller. Ensure correct polarity (+ to + and - to -).
  3. Wire the PV Array: Connect the solar panel (PV array) cables to the photovoltaic array terminals (③). Ensure correct polarity.
  4. Wire the Load (Optional): Connect your DC loads to the load terminals (⑤). Ensure correct polarity.
Diagram showing steps to wire the solar charge controller: open cover, connect battery, then connect PV.

Figure 2: Step-by-step visual guide for wiring the controller.

Comprehensive wiring diagram for a solar system including PV array, controller, battery, inverter, and load.

Figure 3: Example wiring diagram for a complete solar power system.

4. Operating Instructions

4.1 LCD Display and Navigation

The LCD provides real-time information about your solar system. Use the Menu Button (⑥) to cycle through different display screens and the Set Button (⑦) to change parameters.

Diagram showing various screens of the LCD display interface on the solar charge controller.

Figure 4: At-a-glance display interface showing various operational screens.

Common display screens include:

  • Main Interface: Displays battery voltage (BAT), system voltage (e.g., 12V), and temperature.
  • System Voltage Select: Allows selection of system voltage (e.g., Ut:00).
  • Total Charge Power: Shows accumulated PV charge (PV, 0AH).
  • Load Mode: Displays current load control mode (e.g., 24H, OFF).
  • Total Load Power: Shows accumulated load consumption (LOAD, 0AH).
  • Load Disconnect Voltage: Configurable voltage at which load is disconnected (e.g., 11.0V OFF).
  • Float Voltage: Displays the float charge voltage (e.g., 13.8V OFF).
  • Load Reconnect Voltage: Configurable voltage at which load is reconnected (e.g., 12.6V ON).

4.2 Battery Type Selection

The controller supports various battery types. You can select the appropriate charging process for:

  • User default
  • Sealed Lead-Acid
  • Flooded Lead-Acid
  • GEL Lead-Acid
  • LiFePO4 (Lithium Iron Phosphate)
  • Li(NiCoMn)O2 (Lithium Nickel Manganese Cobalt Oxide)
Diagram illustrating MPPT+PWM charging and various battery modes supported by the controller.

Figure 5: MPPT+PWM Charging and supported battery modes.

4.3 Load Control Modes

The controller offers four load output modes to configure load output conditions and durations:

  • Manual Mode (24H): Load is continuously on.
  • Solar Light Control Mode: Load turns on at sunset and turns off at sunrise.
  • Solar Light + Time Control: Load turns on at sunset and stays on for a set duration, then turns off.
  • Pure Charger Mode: The controller acts solely as a charger, with no load output.
  • Timing Mode: Load operates based on a user-defined schedule.
Diagram showing different load working modes: Manual, Solar Light Control, and Solar Light + Time control.

Figure 6: Visual representation of the various load working modes.

5. Maintenance

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the controller clean and free from dust and debris.
  • Ensure adequate ventilation around the controller to prevent overheating.
  • Periodically inspect the battery terminals for corrosion and clean if necessary.
  • Monitor the LCD display for any error codes or unusual readings.
  • If an external temperature sensor is used, ensure it is securely connected and positioned correctly for accurate readings.

6. Troubleshooting

This section provides guidance for common issues. For more complex problems, please contact customer support.

Table 2: Common Troubleshooting Guide
ProblemPossible CauseSolution
Controller not powering onBattery not connected or low voltage; incorrect wiring.Check battery connections and voltage. Ensure battery is connected first.
No charging from PVPV array not connected; insufficient sunlight; PV voltage too low/high.Check PV connections and polarity. Ensure adequate sunlight. Verify PV open circuit voltage is within controller limits.
Load not workingLoad disconnected; low battery voltage; incorrect load mode setting.Check load connections and polarity. Ensure battery voltage is above LVD. Verify load control mode settings.
Inaccurate temperature readingExternal temperature sensor not connected or faulty.Ensure external temperature sensor is properly connected. If not, the controller uses a default compensation.

7. Specifications

Table 3: Technical Specifications
ParameterPOW-Keeper1220 (20A)POW-Keeper1230 (30A)POW-Keeper1240 (40A)
Rated charge current20A30A40A
System rated voltage12V/24V Auto work
Voltage range of battery8-32V
Max open voltage of PV module55V75V100V
Battery typeUser default, Sealed, Flooded, GEL, LiFePO4
Equalized charging voltageMaintenance-free lead acid battery: 14.6V; GEL: No; Lead acid flooded battery: 14.8V
Absorption charging voltageMaintenance-free lead acid battery: 14.4V; GEL: 14.2V; Lead acid flooded battery: 14.6V
Floating charging voltageMaintenance-free lead acid battery, GEL, Lead acid flooded battery: 13.8V
Low voltage re-connection (LVR)Maintenance-free lead acid battery, GEL, Lead acid flooded battery: 12.6V
Low voltage disconnection (LVD)Maintenance-free lead acid battery, GEL, Lead acid flooded battery: 10.8V
Static loss<9.2mA (12V); <11.7mA (24V)
High voltage disconnection (HVD)16V (24V x 2)
Duration of absorption charging2 Hours
Light control voltage5V
Charge loop voltage drop<0.29V
LCD Temperature-20°C~+70°C
Operating Temperature-20°C-+55°C (To run at full rated current continuously)
Working humidity<95% No condensation
Protection classIP30
Dimension (LxWxH) mm123x178x48135x202x55150x220x67

8. User Tips

  • For optimal performance, ensure your solar panel array voltage is well within the controller's maximum open voltage limits for your specific model (55V, 75V, or 100V).
  • Always double-check the polarity of all connections (PV, battery, load) before powering on to prevent damage to the controller and connected devices.
  • When setting up, configure the battery type first to ensure correct charging parameters are applied.
  • Utilize the various load control modes to optimize power usage for your specific application, such as automatic lighting control for street lamps.
  • If you experience any issues, refer to the troubleshooting section before contacting support. Many common problems can be resolved with simple checks.

9. Warranty and Support

For warranty information and technical support, please refer to the documentation included with your product or contact PowMr Official Store customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

© 2023 PowMr. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.