Tuya 24 Channel Smart Zigbee Wireless Relay Switch Module

Contents

Tuya 24 Channel Smart Zigbee Wireless Relay Switch Module User Manual

Model: 24 Channel Smart Zigbee Wireless Relay Switch Module

1. Product Overview

The Tuya 24 Channel Smart Zigbee Wireless Relay Switch Module is designed for smart home automation, allowing remote control of various devices. It integrates Zigbee connectivity for smart app control and supports 433MHz RF remote control (if purchased separately). This module provides 24 independent relay channels for versatile applications.

Top-down view of the Tuya 24 Channel Smart Zigbee Wireless Relay Switch Module
Figure 1: Tuya 24 Channel Smart Zigbee Wireless Relay Switch Module

2. Setup and Installation

2.1 Power Supply

  • The module supports a 12V power supply.
  • Alternatively, it can be powered via a Type-C interface. A power supply above 5V 2A is recommended for Type-C.

2.2 Wiring Diagram

Refer to the diagram below for proper connection of power, load, and control interfaces. Ensure all connections are secure before applying power.

Wiring diagram for the 24-channel relay module showing power input, load connections, and control interfaces.
Figure 2: Wiring Diagram

Key Components and Connections:

  • 1-12 Passive Control Interfaces for Relays: Connect your devices to be controlled by relays 1 through 12.
  • 12-24 Relay Passive Control Interface: Connect your devices to be controlled by relays 12 through 24.
  • Zigbee Control Module: Integrated module for smart app control.
  • Set Button: Used for pairing and factory reset.
  • 5V Type-C Power Supply Port: Alternative power input.
  • 12V Power Input Port: Primary power input (12V).
  • Relay Status Indicator Light: Provides visual feedback on relay status.
  • 433MHz Superheterodyne Receiving Module: For RF remote control functionality.
  • Load Connections (L, N): Connect your load (e.g., light, motor) to these terminals. The module supports AC0-250V 10A and DC0-30V 10A.

2.3 Zigbee Gateway Compatibility

The Zigbee version of this module is fully compatible with Tuya Zigbee gateways. For other third-party Zigbee gateways (e.g., zigbee2mqtt), there may be compatibility issues that limit control to only 8-10 channels instead of all 24. If full 24-channel control is required with a non-Tuya gateway, it is recommended to consider an 8-channel relay module designed for broader compatibility.

3. Operating Instructions

3.1 WiFi Remote Control (Tuya Smart App)

  1. Download the "Tuya Smart" application from your device's software market.
  2. Install the app and register an account.
  3. Power off the relay module, then restart it.
  4. Open the Tuya Smart app and click the "+" sign in the upper right corner to add a new device. Follow the in-app instructions to complete the pairing process.

3.2 RF Remote Control (Optional)

This functionality is only available if you have purchased a compatible 433MHz RF remote control.

Learning Self-Locking Mode:

  1. Quickly press the "Setting" button on the circuit board 5 times.
  2. Relay 1 will flash, indicating it is in learning mode.
  3. (Optional) To change the learning relay number, click the "Setting" button again.
  4. While in learning mode, long-press a key on your remote control to learn that key.
  5. You can continue to press other keys on the remote to assign them to different relays.
  6. After completing the operation, power off the module and restart it for the changes to take effect.

Note: If the remote control learning process does not proceed as expected, power off the module and try again.

3.3 Jog Setting (Momentary Mode)

Jog settings must be configured through the Tuya Smart App.

Jog Setting Instructions:

  • In the Tuya App, navigate to the settings for your relay module.
  • Input 1 for the channel number: The current jog time for Channel 1 will be displayed. You can then modify this time (e.g., to 500 milliseconds).
  • Input 2 for the channel number: The current jog time for Channel 2 will be displayed. You can then modify this time (e.g., to 500 milliseconds).
  • The jogging time range is 1 to 999,999,999 milliseconds.
  • Input 0 for jogging time: This means the channel will not operate in jog mode.
  • Set other channels by following the same analogy.

4. Maintenance

4.1 Restore Factory Settings

To restore the module to its factory default settings:

  1. Press and hold the "Setting" button on the circuit board for 10 seconds.
  2. Release the button when the indicator light flashes quickly. The module is now reset.

5. Troubleshooting

  • Limited Channels with Non-Tuya Zigbee Gateways: If you are using a third-party Zigbee gateway and can only control 8-10 channels, this is likely due to network chip compatibility. Consider using a Tuya Zigbee gateway for full 24-channel functionality or an 8-channel module if using other gateways.
  • Remote Control Learning Issues: If the remote control learning process fails, power off the module completely, then power it back on and retry the learning steps.
  • Module Not Responding: Ensure the module is receiving adequate power (12V or 5V 2A via Type-C). Check all wiring connections for security and correctness.
  • App Connection Problems: Verify your Wi-Fi network is active and the Tuya Smart app has the necessary permissions on your smartphone. Ensure the module is within range of your Zigbee gateway.

6. Specifications

FeatureSpecification
BrandTuya
Model24 Channel Wireless Relay Switch Module
Communication MethodZigbee, 433MHz RF (for remote control)
Number of Channels24
Power Supply12V DC or Type-C (5V 2A recommended)
Load CapacityAC0-250V 10A, DC0-30V 10A
Jog Time Range1 - 999,999,999 milliseconds
Product Length20 cm
Product Width15 cm
Product Height6 cm
Product Weight0.425 kg
OriginMainland China

7. User Tips

  • Gateway Choice: For optimal performance and full 24-channel control, it is highly recommended to use this module with a Tuya Zigbee gateway.
  • Power Supply Stability: Ensure a stable power supply within the specified voltage range (12V or 5V 2A for Type-C) to prevent unexpected behavior or damage.
  • Testing Connections: Before finalizing installation, test each relay channel and control method (app and RF remote) to confirm proper functionality.

8. Warranty and Support

For warranty information, technical support, or further assistance, please contact your original point of purchase or the manufacturer's customer service. Keep your purchase receipt as proof of purchase.

© 2023 Tuya. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.