Main Features
- Dual-channel Wireless Shotgun Mic, 14mm Gold-plating Capsule
- 48kHz/32-bit Float Recording, Wired/Wireless Dual Modes
- 32G On-board Recording for 40-hour Audio Storage
- Exclusive Comica Audio APP for More Functions
- Support One-key Denoise/Low-cut/High-frequency Boost
- Digital & Analog Outputs, Universal for Camera/Smartphone/PC
- Intelligent Power Switch and Auto-sensing 3.5mm Output
- Support Mono/Stereo/Safety Mode and Real-time Monitor
- OLED Screen for Monitoring and Visual Operation
- Battery Life Up to 32H/10H in Wired/Wireless Mode
- Working Range Up to 200m, Stable & Low Latency (Open Area)
- Upgraded Shock-mount & Windproof Accessory
Important Notice & Safety Information
- When used for a long time, connect to external power for charging. AC/DC power is not supported to avoid noise.
- In wireless mode, for better recording, adjust transmitter gain first. After maximum gain, adjust receiver gain accordingly.
- If using a boom pole adapter and screw, install the adapter screw with the grooved side facing outward. Otherwise, it may be difficult to remove.
- VM40 transmitter has a default time setting. For first use, calibrate time via the Comica Audio APP to avoid inconsistent time stamps.
- This device is a high-precision instrument. Avoid falling, collision, or pounding.
- Do not use this equipment near heat sources or interference sources (radiators, ovens, refrigerators, air conditioners).
- If pick-up distance is close or when used outdoors, use the wind muff to prevent sound bursts or reduce wind noise.
- Do not use the equipment in rain or damp environments to avoid short-circuit danger.
Please use it face-to-face, and don't turn your back to the receiver. Otherwise, it is easy to generate breakpoints.
Don't block the antenna positions of the TX and RX during use to avoid affecting the wireless distance.

Packing List
One-channel Version (VM40)
Main Parts:
- Shotgun Microphone (Transmitter) x1
- Receiver x1
Accessories:
- 2 in 1 Charging & Output Cable x1
- 3.5mm TRS-TRS Audio Output Cable x1
- 3.5mm TRRS-TRRS Audio Output Cable x1
- Shock Mount x1
- 3/8 Male to 5/8 Female Stand Adapter x1
- 5/8 Male to 3/8 Female Screw x1
- 3/8 Male to 1/4 Female Screw x1
- Windscreen x1
- Wind-muff x1
- Pin x1
- Carry Case x1
- User Manual x1
- Warranty Card x1
Dual-channel Version (VM40 COMBO)
Main Parts:
- Shotgun Microphone (Transmitter) x2
- Receiver x1
Accessories:
- 2 in 1 Charging & Output Cable x1
- 3.5mm TRS-TRS Audio Output Cable x1
- 3.5mm TRRS-TRRS Audio Output Cable x1
- 3 in 1 Charging Cable x1
- Shock Mount x2
- 3/8 Male to 5/8 Female Stand Adapter x2
- 5/8 Male to 3/8 Female Screw x2
- 3/8 Male to 1/4 Female Screw x2
- Windscreen x2
- Wind-muff x2
- Pin x1
- Carry Case x1
- User Manual x1
- Warranty Card x1
Components and Instructions
Microphone (Transmitter)

- Mic Capsule
- Low-cut Indicator: Lights up blue when low-cut is turned on.
- High-frequency Boost Indicator: Lights up blue when high-frequency boost is turned on.
- On-board Recording Indicator: Lights up red when on-board recording is turned on.
- Function Button: Short-press to switch on/off low-cut/high-frequency boost; long-press to turn on/off on-board recording.
- Working Indicator: Green light on in wired mode; in wireless mode, blue light flashes when pairing, and blue light on when paired.
- Mode Button: When the audio cable is connected, long press to turn on/off the wireless mode; when the audio cable is not connected, long press to turn on the microphone and enter wireless mode/turn off the microphone; short press to switch on/off the safety mode.
- Gain Control Knob: Rotate to adjust the gain.
- 3.5mm Output Port: To identify TRS/TRRS plug automatically and output analog audio; microphone automatically turns on/off when connecting/disconnecting a device.
- Pairing Hole: When the wireless connection is abnormal, use the pin to short-press the pairing hole to re-pair.
- USB-C Port: Connect USB device to output digital audio; microphone automatically turns on/off when connecting/disconnecting a device; connect a power source to charge; connect a computer to copy on-board recording audio.
Note: When the microphone is powered off, long press the function button and the mode button in sync to enter the copy mode. Connect the microphone to the computer via the 2 in 1 charging & output cable to copy the on-board recording audio.
Transmitter Screen Display Instruction

- Wireless Mode Off: Indicates wireless function is off.
- Pairing...: Indicates the device is searching for a receiver.
- Paired: Indicates successful wireless connection.
- Nor (Normal Mode): Standard recording mode.
- Sft (Safety Mode): Records a backup audio track at -6dB.
- Battery Power: Displays current battery level.
- On-board Recording Time: Shows elapsed recording time.
- Audio Dynamic Bar: Visual representation of audio levels.
- Copy Mode: Indicates the device is in data transfer mode.
Receiver

- USB-C Output/Charging Port: Connect USB device to output digital audio; connect to a power source for charging.
- Pairing Hole: When the wireless connection is abnormal, use the pin to short-press the pairing hole to re-pair.
- 3.5mm Output Port: To identify TRS/TRRS plug automatically and output analog audio.
- 3.5mm Monitoring Port: Plug in 3.5mm TRS/TRRS earphones for monitoring.
- CH1/Denoise Button: In single channel, short press to reduce microphone gain; in dual channel, short press to increase and decrease the gain of channel 1 in a cycle; long press to adjust the denoise of channel 1 and channel 2 in a cycle (turn on 1st level denoise - turn on 2nd level denoise - turn off denoise).
- Power/Mode Button: Long press to power on/off; short press to switch mono/stereo/safety mode.
- CH2/On-board Recording Button: In single channel, short press to increase microphone gain; in dual channel, short press to increase and decrease the gain of channel 2 in a cycle; long press to turn on/off the on-board recording of channel 1 and channel 2 in sync.
- Belt Clip
Note:
1. Denoise function does not work on on-board recording.
2. Long-press the CH1 button and CH2 button in sync to reset the Bluetooth. After resetting, the microphone can be connected to a new phone by Comica Audio App.
Receiver Screen Display Instruction

- Mono: Mono Mode.
- Stereo: Stereo Mode.
- Safety: Safety Mode.
- Denoise Off: Denoise function is off.
- 1st Level Denoise: First level of noise reduction.
- 2nd Level Denoise: Second level of noise reduction.
- Bluetooth Paired/Not Paired: Indicates Bluetooth connection status.
- Phone Speaker Monitoring On/Off: Indicates if phone speaker monitoring is active.
- Receiver Power: Displays receiver battery level.
- Transmitter Power: Displays transmitter battery level.
- Gain Level: Shows current audio gain.
- Muting On: Indicates microphone is muted.
- Audio Dynamic Bar: Visual representation of audio levels.
Note:
1. When the receiver outputs audio through the USB port, it is monitored by the phone speaker by default. Users can switch between phone speaker monitoring and receiver headphone monitoring through the Comica Audio App. For detailed instructions, kindly refer to the App operation guide at the manual's end.
2. One audio dynamic bar is displayed in one channel, and two audio dynamic bars are displayed in two channels.
3. The mute function can be turned on/off through the App.
Setup
Wired Mode: 3.5mm Analog Output
Connect the shotgun microphone to the camera/smartphone/computer through the 3.5mm audio cables, or connect to the camcorder/recorder through the 3.5mm TRS-XLR audio cable.

Note:
1. TRRS-TRRS audio cable is for cameras/smartphones/computers. TRS-TRS audio cable is for some cameras not compatible with TRRS-TRRS audio cable. TRS-XLR audio cable is for recorders/camcorders (please prepare by yourself).
2. When using a non-step-down TRS-XLR audio cable, do not turn on the 48V phantom power of the recorder/camera, and the shotgun microphone must be turned on and off manually; when using a step-down TRS-XLR audio cable, users can turn on the 48V phantom power, and the shotgun microphone can turn on and off automatically.
USB Digital Output
Connect the shotgun microphone to the smartphone or computer through the 2 in 1 charging & output cable and related OTG audio adapter/cable (if needed).

Note:
1. It's recommended to insert the USB end with the magnetic ring into the microphone and connect the other end to the smartphone/computer.
2. When using with Lightning interface devices, please prepare a USB-Lightning adapter/cable that supports OTG function.
Wireless Mode Pairing
The transmitter and receiver are paired by default at the factory. If the wireless connection is abnormal, short-press the pairing holes of the transmitter and receiver with the pin to re-pair.

Microphone (Transmitter) Mounting
Use with arm stands, boom poles, and tripods.

Note: If you need to use a boom pole adapter and an adapter screw, please install the adapter screw with the grooved side facing outward. Otherwise, it may not be able to take out.
Operating Instructions
Power On/Off & Mode Selection
- Intelligent Power Switch: The shotgun microphone supports automatically power on/off when connecting/disconnecting the output device.
- Mode Button (Transmitter): Long press to turn on/off wireless mode (if cable connected) or turn on/off microphone and enter wireless mode (if no cable). Short press to switch on/off safety mode.
- Power/Mode Button (Receiver): Long press to power on/off. Short press to switch Mono/Stereo/Safety mode.
Audio Adjustments
- Gain Control Knob (Transmitter): Rotate to adjust the input gain.
- CH1/Denoise Button (Receiver): Short press to reduce microphone gain (single channel) or cycle through increasing/decreasing gain for channel 1 (dual channel). Long press to adjust denoise levels (1st level, 2nd level, off).
- CH2/On-board Recording Button (Receiver): In dual channel, short press to increase/decrease gain for channel 2.
- One-key Denoise/Low-cut/High-frequency Boost: Use the Function Button on the transmitter to short-press and switch these features on/off. CalMix® denoise reduces background noise. Low-cut filters frequencies below 100Hz. High-frequency boost enhances clarity.
On-board Recording
The VM40 features 32GB built-in storage for up to 40 hours of uncompressed audio. To start/stop on-board recording, long-press the Function Button on the transmitter. To access recorded files, enter copy mode (microphone off, long-press Function Button and Mode Button simultaneously), then connect to a computer via the 2 in 1 charging & output cable.
Monitoring
- OLED Screen: Both transmitter and receiver have high-definition screens to display battery power, wireless status, audio dynamics, channel mode, gain level, etc.
- 3.5mm Monitoring Port (Receiver): Plug in 3.5mm TRS/TRRS earphones for real-time audio monitoring.
Comica Audio App Control
The official Comica Audio App (available for iOS and Android) allows remote monitoring and control via smartphone Bluetooth.

- Search and download the "Comica Audio" App in your mobile app store.
- Turn on your mobile phone's Bluetooth.
- Open the App to search and pair device VM40.
- The receiver and transmitter can be set and operated through the App, including monitoring microphone status, changing settings, and managing multiple devices.
- Time Calibration: VM40 transmitter is set to a default time. For the first use, calibrate the time through the APP: Settings -> Date -> Auto Time Setting/Manual Setting -> Synchronize to device.
Maintenance
- Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
- Store the device in its carry case when not in use to protect it from physical damage.
- Do not attempt to disassemble or repair the device yourself. Refer to authorized service personnel for any repairs.
- Ensure all cables are connected securely to prevent accidental disconnections or damage.
Troubleshooting
Common Issues & Solutions
- Abnormal Wireless Connection: If the wireless connection is abnormal, use the provided pin to short-press the pairing hole on both the transmitter and receiver to re-pair.
- Audio File Extraction: To extract audio files from the transmitter's on-board recording, ensure the microphone is powered off. Long-press the Function Button and Mode Button simultaneously to enter copy mode. Then, connect the microphone to your computer via the 2 in 1 charging & output cable.
- Phone Playback Issues: When the receiver is connected to a mobile phone, you can enable phone playback via the Comica Audio App. Check the screen: if the speaker icon is displayed, the phone's speaker is external; if not, it's using the phone's internal speaker. Adjust through the App settings.
- App Connection Problems: Ensure your mobile phone's Bluetooth is on. After resetting the receiver's Bluetooth (long-press CH1 and CH2 buttons simultaneously), open the Comica Audio App and click 'Add Device' to search for and connect to the VM40.
- Noise Problems: Ensure proper antenna positioning (face-to-face, no obstructions). Use the wind muff when outdoors or in windy conditions. Utilize the one-key denoise and low-cut features to reduce background and low-frequency noise.
Specifications
| Feature | Specification |
|---|---|
| Wireless Type | 2.4GHz |
| Transmitting Power | +10dBm |
| Receiving Sensitivity | -96dBm |
| Antenna | Ceramic Antenna |
| Sound Delay | <20ms |
| Polar Pattern | Super Cardioid |
| Frequency Response | 20Hz ~ 20kHz |
| Low-cut | -3dB @ 100Hz |
| High-frequency Boost | +3dB @ 10kHz |
| Output Impedance | 600Ω |
| Sensitivity | -38dB ~ -18dB re 1V/Pa(12mv ~ 125mv @ 94dB SPL) ±2dB @ 1kHz |
| S/N | 75dB SPL(A-weighted, as per IEC651) |
| Equivalent Noise | 19dB SPL(A-weighted, as per IEC651) |
| Maximum SPL | 130dB SPL(@ 1% THD) |
| Dynamic Range | 111dB SPL(A-weighted, as per IEC651) |
| Analog Output | 3.5mm TRRS/TRS |
| Digital Output | USB-C 48kHz/24bit |
| Battery (Transmitter) | Li-polymer 3.7V 350mAh |
| Battery (Receiver) | Li-polymer 3.7V 330mAh |
| Battery Life (Transmitter) | Wired Mode 32 Hours; Wireless Mode 10 Hours; On-board Recording Mode 5 Hours |
| Battery Life (Receiver) | 8 Hours |
| Dimensions (Transmitter) | Φ22mm x L224mm |
| Dimensions (Receiver) | 54 x 48 x 22mm |
| Net Weight (Transmitter) | 94g |
| Net Weight (Receiver) | 29.5g |
| Operating Temperature | 0℃ ~ 50℃ |
| Storage Temperature | -20℃ ~ 60℃ |
Firmware Upgrade
Shotgun Microphone Upgrade
Download the VM40 firmware upgrade package to your computer from the Comica official website. Enter the copy mode when the mic is turned off (long-press the function button and mode button in sync), then connect the mic to the computer via a USB data cable, copy the firmware upgrade package to the VM40 TX---UPDATA folder, disconnect the USB data cable and restart the mic to upgrade automatically.
Receiver Upgrade
Enter the copy mode when the receiver is turned off (press and hold the CH1 or CH2 button, and long-press the power button), then connect the receiver to the computer via a USB data cable, copy the firmware upgrade package to the VM40 RX---UPDATA folder, disconnect the USB data cable and restart the receiver to upgrade automatically.
Bluetooth Connection Upgrade
Open the Comica Audio App and connect the VM40 microphone. Then go to the VM40 homepage and click the settings icon in the upper right corner---Universal---Firmware Upgrade.
User Tips
- The VM40 offers excellent quality and a wide range of features, making it a versatile choice for various recording needs.
- Consider the VM40 for its advanced features and quality if you're looking to future-proof your audio setup.
- The product is generally well-regarded for its performance and utility.
Warranty & Support
COMICA is a registered trademark owned by Commlite Tech Co., Ltd.
For support and further information, please refer to the included Warranty Card in your package.
You can also find more resources and contact information through the following channels:
- Website: comica-audio.com
- Facebook: Comica Audio Tech Global
- Instagram: Comica Audio
- YouTube: Comica Audio
- Email: support@comica-audio.com