LILYGO T-Dongle-S3

Contents

T-Dongle-S3 ESP32-S3 Development Board User Manual

Comprehensive guide for setup, operation, and maintenance.

1. Introduction

The T-Dongle-S3 is a compact development board based on the ESP32-S3 Xtensa LX7 microprocessor. Designed in a convenient USB dongle form factor, it integrates Wi-Fi and Bluetooth 5 connectivity, a TF card slot, and an optional 0.96-inch ST7735 IPS LCD display. This manual provides essential information for setting up, operating, and maintaining your T-Dongle-S3 development board.

Front and back view of T-Dongle-S3 with LILYGO LCD

Figure 1: T-Dongle-S3 with LCD (Front and Back)

2. Features

  • Microcontroller: ESP32-S3 Xtensa LX7 microprocessor
  • Wireless Connectivity: Integrated Wi-Fi 802.11 b/g/n and Bluetooth 5
  • Memory: 16MB Flash
  • Storage: TF Card slot for external memory
  • Display (Optional): 0.96-inch ST7735 IPS LCD with 80x160 resolution, 65k full-color display, 4-Wire SPI interface, 3.3V working power supply.
  • Interface: USB Type-A dongle form factor
  • Antenna: Built-in highly sensitive ceramic antenna for Wi-Fi and Bluetooth
  • Development Platforms: Supports Arduino-IDE, PlatformIO-IDE, and MicroPython
  • Buttons: Boot button for programming and control
  • Shell: Translucent casing
Comparison of T-Dongle-S3 with LCD and without LCD

Figure 2: T-Dongle-S3 Variants (With LCD and Without LCD)

T-Dongle-S3 key features including LCD, ESP32-S3, TF Card Slot, Translucent Shell, Grove, OTG

Figure 3: Key Features Overview (Note: Chipset is ESP32-S3)

3. Specifications

T-Dongle-S3 detailed specifications including MCU, Wireless, Platform, Onboard functions, and LCD details

Figure 4: Detailed Specifications

ComponentDetail
MCUESP32-S3 Xtensa LX7 microprocessor
Flash Memory16MB
Wireless ConnectivityWi-Fi 802.11 b/g/n, Bluetooth 5
Development PlatformsArduino-IDE, PlatformIO-IDE, MicroPython
Onboard FunctionsBoot button, TF card slot, Built-in ceramic antenna
LCD Display (Optional)0.96 inch ST7735 IPS LCD, 80x160 resolution, 65k color, 4-Wire SPI, 3.3V
Dimensions (L x W x H)58.6mm x 17.9mm x 8.7mm
T-Dongle-S3 dimensions: Length 58.6mm, Width 17.9mm, Height 8.7mm

Figure 5: T-Dongle-S3 Dimensions

T-Dongle-S3 pinout diagram showing MCU, Flash, Boot Button, TF Card pins (SDMMC_D0-D3, CLK, CMD), USB pins (DN, DP), LED pins (DI, CI), and ST7735 LCD pins (CS, SDA, SCL, DC, RES, PIN, LED)

Figure 6: T-Dongle-S3 Pinout Diagram

4. Setup

  1. Unpacking: Carefully remove the T-Dongle-S3 from its packaging. Ensure all components are present.
  2. Connecting to a Computer:
    • Remove the protective cap from the USB-A connector.
    • Insert the T-Dongle-S3 into an available USB-A port on your computer. The device will draw power and establish a data connection.
    T-Dongle-S3 plugged into a computer's USB port

    Figure 7: T-Dongle-S3 Connected to a Computer

  3. TF Card Insertion (Optional):
    • Locate the TF card slot on the side of the dongle.
    • Gently insert a standard TF (MicroSD) card into the slot until it clicks into place.
    • To remove, push the card slightly inwards until it springs out.
    T-Dongle-S3 with a TF card partially inserted into its slot

    Figure 8: TF Card Insertion

  4. Development Environment Setup:

    The T-Dongle-S3 supports various development environments. Refer to the official documentation for your chosen platform (Arduino-IDE, PlatformIO-IDE, or MicroPython) for detailed instructions on driver installation and board configuration.

5. Operation

  • Power On: The device powers on automatically when plugged into a USB port.
  • Boot Button: The onboard boot button is primarily used for entering bootloader mode to flash new firmware onto the ESP32-S3. Consult your development environment's guide for the specific procedure.
  • LCD Display (if applicable): If your T-Dongle-S3 includes the 0.96-inch ST7735 LCD, it can be programmed to display information. Ensure your firmware includes the necessary display libraries and initialization code.
  • TF Card Usage: Once a TF card is inserted and properly initialized in your firmware, you can read from and write to it for data logging, configuration storage, or other applications.
  • Wireless Communication: Utilize the integrated Wi-Fi and Bluetooth capabilities to connect to networks, other devices, or cloud services as programmed.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the dongle. Avoid using liquids or abrasive cleaners.
  • Storage: Store the T-Dongle-S3 in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Handle the device with care to avoid physical damage to the USB connector, TF card slot, or the optional LCD screen.
  • Firmware Updates: Regularly check for firmware updates from the manufacturer or community to ensure optimal performance and access to new features.

7. Troubleshooting

  • Device Not Powering On:
    • Ensure the USB-A connector is fully inserted into a working USB port.
    • Try a different USB port or computer to rule out port issues.
  • Firmware Upload Failure:
    • Verify that the correct drivers are installed for the ESP32-S3.
    • Ensure the board is in bootloader mode (often by holding the Boot button while connecting or resetting).
    • Check your development environment settings for correct board selection and serial port.
  • LCD Display Not Working (if applicable):
    • Confirm that your firmware includes the necessary libraries for the ST7735 LCD and that it is correctly initialized.
    • Check for any visible damage to the screen or its connection.
  • TF Card Not Detected:
    • Ensure the TF card is inserted correctly and fully seated in the slot.
    • Verify that your firmware includes the necessary code to initialize and access the TF card.
    • Try a different TF card to rule out a faulty card.
  • Wi-Fi/Bluetooth Connectivity Issues:
    • Check your firmware for correct Wi-Fi/Bluetooth initialization and credentials.
    • Ensure the device is within range of the network or Bluetooth device.

8. User Tips

  • Protecting the USB-A Interface: The "Virtual TF card" (likely a placeholder or non-functional slot) has no memory. If you need to remove it, always insert a common TF card first to protect the USB-A interface from damage. An ordinary TF card can be used normally in the TF card slot.
  • Development Resources: Explore online communities and forums dedicated to ESP32-S3 development for examples, libraries, and troubleshooting assistance.

9. Warranty and Support

For technical support, warranty claims, or further assistance, please contact the seller or manufacturer directly. Keep your purchase records handy for any inquiries.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.