1. Product Overview
The LILYTECH ZL-U05DM is a universal control system designed for air conditioners, featuring a digital display and remote control for convenient operation. It supports various functions including cooling, heating, and fan modes, and is compatible with PG motors.
Note: The product version may be updated over time (e.g., from V2.0 to V4.0/V4.3), which may result in slight differences in appearance. This does not affect the product's functionality.
2. Package Contents
- 1 x Control Panel (ZL-U05DM)
- 1 x Remote Control
- 1 set x Accessories (including transformer, sensors, wiring harnesses)
3. Setup and Installation
3.1 PG Motor Hall Detecting Connection
For PG motors with Hall elements, connect according to the wiring diagram strictly. If the connection is incorrect or disconnected, the yellow LED will flash, and the indoor fan and compressor will shut down, remaining in a protection state.
- If there are Hall elements on the PG motor, please connect it according to the wiring diagram strictly.
- If there is no Hall element on the PG motor, please connect Vout to GND (short point 1 and 2).
Symbols Description:
- VCC: Power+
- Vout: Signal Output
- GND: Power-
3.2 System Wiring Diagram
Refer to the detailed wiring diagram for connecting the indoor fan, outdoor fan, four-way valve, transformer, and compressor. Ensure all connections are secure and follow electrical safety guidelines.
4. Operating Instructions
4.1 Display Information
The digital display shows the set-point in cooling and heating modes. It also provides error codes and status remarks:
| Display | Remark |
|---|---|
| E1 | Room sensor failure |
| E2 | Pipe sensor failure |
| dF | Defrosting |
| FA | Fan mode |
| dr | Dry mode |
| FP | Indoor fan without feedback |
4.2 Turn Online in Auto Working Mode
- If the room temperature is < 21°C, it will run in heating mode.
- If the room temperature is > 27°C, it will run in cooling mode.
- If between 21-27°C, it will run in fan mode.
4.3 Compressor Delay Protection
After the compressor is de-energized, it needs to rest for 3 minutes before restarting.
4.4 Heating Mode Remark: Avoid Cold Wind
- After compressor starts, the fan will run as follows for a maximum of 2 minutes:
- When indoor pipe temperature ≤ 33°C, fan stops.
- When indoor pipe temperature ≥ 38°C, fan speed is low.
- When indoor pipe temperature > 38°C, fan run at set speed.
4.5 Blow Out Residual Heat
After compressor stops, the fan keeps running for a maximum of 2 minutes. When indoor pipe temperature ≥ 30°C, fan keeps running till to 30°C.
4.6 Remote Control Functions
- ON/OFF key: Switch between online and offline.
- MODE key: Switch between auto, cool, dry, heat, and fan mode.
- FAN key: Switch between low, medium, high, and auto fan mode. In dry mode, or during avoiding cold wind status in heat mode, fan speed is low.
- VANE key: Switch swing on/off.
- Temp key: Set temperature.
- TIMER key: Set timer among timer-on, timer-off and without-timer. In set status, press Time-key to set the time of the timer.
- Clock set: Press CLOCK key, then press SET key to select the digit of the time, then press Time-key to set the value.
- SLEEP key: Set the sleep on/off. When sleep is set, the air conditioner will be offline after running for 8 hours: In cool mode, the real set point will increase 1°C for the 1st hour, and increase 1°C again for the 2nd hour. In heat mode, the real set point will decrease 2°C for the 1st hour, and decrease 1°C again for the 2nd hour. The real set-point keeps from 3rd hour till offline.
- LOCK key: Press the lock key to lock/unlock the keypad.
5. Maintenance
To ensure optimal performance and longevity of your LILYTECH ZL-U05DM control system, regular maintenance is recommended:
- Keep the control panel and remote control clean and free from dust. Use a soft, dry cloth for cleaning.
- Periodically check all wiring connections to ensure they are secure and free from corrosion.
- Avoid exposing the unit to extreme temperatures or humidity.
6. Troubleshooting
6.1 Display Error Codes
Refer to the 'Display Information' table in Section 4.1 for explanations of error codes (E1, E2, dF, FA, dr, FP) and their corresponding remarks.
6.2 PG Motor Hall Connection Issues
If the yellow LED flashes and the indoor fan and compressor shut down, it indicates an incorrect or disconnected PG motor Hall element connection. Review the wiring as per Section 3.1 and ensure strict adherence to the diagram.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | ZL-U05DM |
| Style | Wall Hanging |
| Power Type | Charger |
| Usage | Indoor |
| Theory | Temperature Controller |
| Display Type | Digital |
| Color | Red+White |
| Material | Plastic |
| Package Length | 17 cm |
| Package Width | 13 cm |
| Package Height | 4 cm |
| Package Weight | 0.479 kg |
8. User Tips
- When installing, double-check all wiring connections against the provided diagrams to ensure proper functionality and avoid error states.
- Users have reported successful installation and perfect operation when correctly integrated into an air conditioning unit.
9. Warranty and Support
For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase records for reference.