JIKONG Smart JIKONG BMS

Contents

Smart JIKONG BMS User Manual

Your comprehensive guide to installation, operation, and maintenance.

1. Product Overview

The Smart JIKONG BMS is an intelligent battery management system designed for large-capacity series lithium battery packs. It offers advanced features for optimal battery performance and longevity.

1.1. Key Features

  • Voltage Acquisition: Precise monitoring of individual cell voltages.
  • High Current Active Balancing: Achieves up to 1A continuous balance current, ensuring battery consistency and extending lifespan.
  • Comprehensive Protection: Includes overcharge, over-discharge, overcurrent, over-temperature, low-temperature, and short-circuit protection.
  • Coulomb Meter: Accurate tracking of battery capacity.
  • Connectivity: Bluetooth communication for mobile APP control, and optional GPS for location tracking.
  • Heating Function: Optional heating to maintain optimal battery temperature in cold environments.
  • Parallel Function: Supports parallel connection of battery packs.
  • Smart Management: Real-time monitoring and parameter adjustment via a dedicated mobile APP (Android/iOS).

The BMS is compact, easy to operate, and suitable for a wide range of applications, including electric bikes, tricycles, low-speed quads, forklifts, cleaning cars, tourist cars, industrial drones, scooters, RV energy storage, energy storage cabinets, power banks, and power tools.

2. Safety Information

Please read and understand all safety instructions before installing or operating the Smart JIKONG BMS. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Always ensure proper wiring and connections. Incorrect wiring can damage the BMS and battery.
  • Do not attempt to open or modify the BMS unit.
  • Keep the BMS away from water, moisture, and extreme temperatures.
  • Ensure the battery pack voltage is within the specified range for the BMS model.
  • In case of any abnormal behavior, disconnect the battery immediately and consult a professional.
  • Wear appropriate personal protective equipment (PPE) when working with batteries.

3. Package Contents

Upon opening your Smart JIKONG BMS package, please verify that all the following items are included:

Package contents of Smart JIKONG BMS
Figure 1: Smart JIKONG BMS Package Contents
  • Smart JIKONG BMS Unit
  • Operating Manual (this document)
  • Pack Box
  • NTC Temperature Sensor (40cm)
  • Heating Cable (16cm) (if applicable to model)
  • CAN Cable (25cm) (if applicable to model)
  • Switch (50cm)
  • Wires (70cm)

4. Specifications

4.1. General Specifications

AttributeValue
Brand Namesmart jikong bms / JIKONG
TypeLIFEPO4 Battery BMS, LI-ION Battery BMS
Balance FunctionActive Balanced BMS
Hardware or SmartSMART BMS
Charge and Discharge PortCommon Port BMS
FunctionOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
CertificationCE, FCC, RoHS
OriginMainland China
Usage ScenarioPower BMS, Energy Storage BMS, 3C Digital BMS
Over charge protectionYES
Short circuit protectionYES
BluetoothYES
Balance Current1A, 2A
Charging Current200A, 100A, 300A (model dependent)
Discharge current100A, 200A, 300A (model dependent)
Accessory TypeCharger Accessories
Applicationslithium battery rated

4.2. Basic Parameters (JK-B1A8S-10P example)

ProjectParameterUnit
Supply voltage10-36V
Operating power consumption<900mW
Operating temperature-30-70°C
Maximum number of collection strings8String
Maximum balancing current1A
Maximum charging current100A
Maximum discharge current100A
Maximum instantaneous current200A
Maximum internal loop resistance0.8mΩ
Protective plate size153.9*107*17.6mm
Finished weight411g

4.3. Default Parameters (JK-B1A8S-10P example)

ParameterLi-Ion DefaultLiFePO4 DefaultLTO DefaultUnit
Balancing initial voltage332V
Maximum balancing current111A
Unit overcharge voltage4.23.62.7V
Single overcharge protection recovery4.183.552.65V
Monomer undervoltage protection2.822.61.8V
Single undervoltage protection recovery2.852.651.85V
Automatic shutdown voltage2.82.51.7V
SOC-0% voltage2.92.61.85V
SOC-100% voltage4.183.52.65V
Trigger balancing differential pressure0.010.010.01V
Charging overcurrent protection delay303030S
Charge overcurrent protection release time606060S
Discharge overcurrent protection delay300300300S
Discharge overcurrent protection release time606060S
Short-circuit protection delay150015001500uS
Charging overtemperature protection temperature707070°C
Charge overtemperature restore temperature606060°C
Discharge overtemperature protection temperature707070°C
Discharge overtemperature recovery temperature606060°C
Charging low temperature protection temperature-20-20-20°C
Charge low temperature to restore temperature-10-10-10°C
MOS Overtemperature protection temperature100100100°C
MOS Overtemperature protection recovery temperature808080°C
Device address000/
Discharge precharge time000S

5. Setup & Installation

5.1. Wiring Diagram

The JK-B1A8S-10P series protection board is suitable for 3-8 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Refer to the diagram below for proper connection.

Wiring Diagram for Smart JIKONG BMS
Figure 2: JK-B1A8S-10P Wiring Diagram

Wiring Steps:

  1. Connect the main negative terminal of the battery pack to the B- terminal on the BMS.
  2. Connect the main positive terminal of the battery pack to the P+ terminal on the BMS.
  3. Connect the balance wires (sampling cable) from each cell string to the corresponding terminals on the BMS (B1, B2, B3, ..., B+). Ensure the last balance wire (B+) is connected to the main positive pole of the battery pack.
  4. Connect the charger to the P+ and P- terminals.
  5. Connect the load (motor, etc.) to the P+ and P- terminals.
  6. If using a heating function, connect the heating cable as shown in the diagram.
  7. If using a display or switch, connect it to the designated interface.

5.2. Device Activation

Before powering on the protection board, double-check all connections:

  • Verify that the balance cable is correctly connected.
  • Ensure that the P- and B- connections are correct.
  • Confirm that the protection board is securely fixed to the battery pack.

The BMS does not have a physical power-on switch. It is designed for charging activation. After the battery assembly is complete, connect the charger (with a voltage 2V higher than the battery pack voltage) to activate the BMS.

For models with a display screen and button, you can also activate the BMS by inserting the cable into the display interface and pressing the button.

6. Operation

6.1. APP Installation

The Smart JIKONG BMS features a mobile application for convenient monitoring and control. To install the APP:

  • For iOS: Search for "JIKONG BMS" in the Apple App Store.
  • For Android: Search for "JK BMS" in the Google Play Store. Android version 7 or higher is required.
Mobile APP QR Code for JIKONG BMS
Figure 3: Mobile APP Link QR Code

6.2. APP Connection and Initial Setup

  1. Ensure GPS and Bluetooth are enabled on your mobile phone.
  2. Open the JIKONG BMS APP. Click on the top left corner to search for devices.
  3. Select your BMS from the device list to connect. The default password is 1234.
  4. For the first startup, parameters need to be set. The default parameter setting password is 123456.
  5. Set the number of units (cell count) and battery type (LiFePO4, Li-Ion, LTO) according to your battery pack.
  6. After setting parameters, return to the real-time status page to check battery status. Ensure no error messages are displayed and normal operation is confirmed. The APP will show the highest voltage in blue and the lowest voltage in red for individual cells.

6.3. Active Equalization

The BMS uses active equalization to transfer energy from high-voltage cells to low-voltage cells. You can set the balance trigger pressure difference (mV) in the APP's parameter settings. Equalization automatically activates when the pressure difference between any two cell strings exceeds the set value and turns off when it falls below the set value. The default balance current is 1A, adjustable based on battery capacity (recommended not to exceed 0.2C).

6.4. Heating Function

The optional heating function uses a resistance heater or heating film to warm the battery in low temperatures, preventing reduced charging/discharging efficiency. The designed heating current is 4A. You can switch this function on/off via the APP. It is recommended to install a temperature control switch (45°C to 65°C normally closed) in series with the heating circuit as a secondary safety measure.

Heating Conditions:

  • Battery temperature is below the low-temperature protection threshold for charging.
  • Connecting a heating film will activate heating and consume battery power.
  • Heating via a charger depends on BMS hardware and charger compatibility.

6.5. Protection Features

The BMS provides comprehensive protection for your battery:

  • Charge Overvoltage Protection: Prevents overcharging by cutting off charging when any cell exceeds the set overcharge voltage. Charging resumes when all cells fall below the recovery voltage.
  • Discharge Undervoltage Protection: Prevents over-discharging by cutting off discharge when any cell falls below the set undervoltage. Discharge resumes when all cells rise above the recovery voltage. Automatic shutdown occurs if any cell falls below the automatic shutdown voltage.
  • Charge Overcurrent Protection: Cuts off charging if the charging current exceeds the set continuous charging current for a specified delay.
  • Discharge Overcurrent Protection: Cuts off discharge if the discharge current exceeds the set continuous discharge current for a specified delay. (Note: Max continuous discharge current should not exceed 100A).
  • Overtemperature Protection: Cuts off charging/discharging if battery temperature exceeds set limits.
  • Low Temperature Protection: Cuts off charging if battery temperature falls below set limits.
  • Short Circuit Protection: Automatically protects against short circuits. The delay and recovery time can be adjusted via the APP.
  • Discharge Precharge Function: Optional feature with a default precharge time of 5 seconds. Can be enabled or disabled as needed.
  • Emergency Switch: In case of over-temperature, over-discharge, over-charge, or cell drop issues, activating the emergency switch in the APP will allow 30 minutes of continued charge/discharge operation, even if cells reach automatic shutdown voltage, to provide emergency use time.
  • Intelligent Sleep: The BMS can enter an intelligent sleep mode (charging/discharging current less than 1A for 26 consecutive hours) to reduce self-consumption. It can be reactivated by pressing a button or connecting a charger.

6.6. Communication Function

The BMS supports optional CAN/RS485 communication. Users can configure the address and communication protocol via the APP based on their specific requirements and scenarios. Refer to the Jikong Protection Board communication protocol document for detailed information.

7. Troubleshooting

7.1. BMS Does Not Turn On

  • Ensure the last B+ line of the balance cable is connected to the positive pole of the battery.
  • Start up after charging: Ensure the charger voltage is greater than 4V (for default BMS) or 10V (for 4S BMS) above the battery pack voltage.
  • Check whether the charger has voltage output.

7.2. Inaccurate Voltage Readings

  • Measure the actual total voltage of the battery pack with a multimeter.
  • Enter this actual total voltage into the "voltage calibration" setting on the APP's parameter setting page.

7.3. Inaccurate Current Readings

  • Ensure both B- and P- terminals of the protection board, which are two 7AWG wires, are connected in parallel. Failure to do so will lead to current errors.
  • Measure the actual current of the battery pack with a clamp meter.
  • Enter this actual current into the "current calibration" setting on the APP's parameter setting page. Higher actual current during calibration leads to higher accuracy.

7.4. Inaccurate Capacity Readings

  • Initial capacity estimation when the BMS is first powered on is often inaccurate.
  • For accurate capacity calibration, fully discharge the battery pack to its cut-off voltage, then fully charge it without interruption.

7.5. Inconsistent String Number

  • Check whether the "unit quantity" (cell count) in the APP's parameter settings is correctly configured.
  • If there is no voltage reading for two or more strings in the middle of the pack, check if the acquisition cable has fallen off or is improperly connected.

8. Maintenance

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the BMS and battery pack clean and free from dust and debris.
  • Monitor battery parameters via the APP periodically to detect any anomalies early.
  • Ensure the battery operates within its specified temperature range.
  • If the BMS is not in use for an extended period, consider activating the intelligent sleep function to minimize power consumption.

9. User Tips

  • Initial Setup: Always perform voltage and current calibration during the initial setup for the most accurate readings.
  • APP Monitoring: Utilize the mobile APP for real-time monitoring of individual cell voltages and overall battery health. This helps in proactive maintenance.
  • Balance Current: Adjust the balance current in the APP based on your battery's capacity to optimize balancing efficiency without overstressing the cells.
  • Cold Weather: If operating in cold climates, consider models with the heating function to protect your battery and ensure consistent performance.
  • Wiring Check: Before activating the BMS, double-check all balance wire connections. Loose connections are a common cause of issues.

10. Warranty & Support

For warranty information and technical support, please refer to the seller or manufacturer's official website. Ensure you retain your proof of purchase for any warranty claims.

Product Certifications: JIKONG BMS products are certified with RoHS, FCC, and CE standards, ensuring quality and safety compliance.

JIKONG BMS Product Certifications (RoHS, FCC, CE)
Figure 4: JIKONG BMS Product Certifications

© 2024 Chengdu Jikong Technology Co.LTD. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.