XHDATA E-100

Contents

XHDATA E-100 UHF VHF Ham Radio Walkie Talkie

User Instruction Manual

1. Introduction

Thank you for purchasing the XHDATA E-100 portable two-way radio. This dual band/dual display/dual watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.

1.1 Content of the Packaging

The package includes the following items:

  • 1 x XHDATA E-100 Radio
  • 1 x USB-C Cable
  • 1 x Antenna
  • 1 x Li-Ion Battery Pack (3000mAh)
  • 1 x Wrist Strap
  • 1 x Belt Clip
  • 1 x User Manual
XHDATA E-100 Product Accessories
Figure 1: XHDATA E-100 Product Accessories (Radio, Antenna, USB-C Cable, 3000mAh Battery, Back Clip, Wrist Strap, Manual)

1.2 Main Features

  • Frequency Range: FM radio 65-108 MHz; AM aviation frequency band 108-136MHz (RX); VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX); UHF1: 400-480MHz (RX&TX); UHF2: 350-390MHz (RX); 400-600MHz (TX).
  • Display: 1.44-inch Large Color Screen Display with blue backlight, full keyboard, fully open menu operation.
  • Memory: Up to 999 Channel Memory, built-in T9 input method, supports display of Chinese and English names.
  • Power: High & Low Power Transmission selectable.
  • Cloning: One-Button Channel Alignment, Wireless Cloning.
  • Language: Chinese & English Language Selection, Channel Voice Announcement.
  • Modes: Multi-Bank, Dual Watch, Dual Standby.
  • Customization: Customizable Boot Screen, Boot Text, Display Mode, Side Key Functions.
  • Aviation Band: Reception limited to VFO Mode (Manual Frequency Entry).
  • VOX: Voice Activated Transmission (VOX) for hands-free communication, 9-level VOX sensitivity adjustment.
  • Security: Frequency Read/Write, Boot Password Protection.
  • Scanning: VFO Scanning (Frequency Range Scanning, Real-Time Frequency & Subtone Scanning) with three resume modes: Carrier, Time, Search.
  • Signaling: Supports Standard & Non-Standard CTCSS (Continuous Tone-Coded Squelch System), CDCSS (Digital Coded Squelch System).
  • Encryption: Analog Communication Encryption Features: Scrambling, Frequency Hopping.
  • Channel Management: Built-in Input Method for Editing Channel Names, Edit Contacts, Add Channels via Self-Station.
  • Repeater Function: Offset Frequency, Direction, Reverse Frequency, Network Disconnection, Repeater Activation Tone.
  • FM Radio: FM Radio Function, supports Frequency Mode & Memory Mode.
  • Weather: Supports NOAA Weather Reception for USA & Canada.
  • Charging: Supports Type-C Charging & Charging Dock for convenient power management.
  • Flashlight: Built-in LED flashlight.
XHDATA E-100 Key Features Overview
Figure 2: Overview of XHDATA E-100 with highlighted features.

2. Safety Information and Regulations

2.1 EU Regulatory Conformance

This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU, and other applicable EU regulations (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). It can be operated under 2000m.

WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU. This information is applicable to EU countries only.

2.2 Compliance with RF Exposure Standards

The radio complies with the following RF energy exposure standards and guidelines:

  • United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
  • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
  • Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition

RF Exposure Compliance and Control Guidelines and Operating Instructions

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.
  • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed FCC RF exposure guidelines.
  • Contact your local dealer for optional accessories.

2.3 Precautions for Portable Terminals

Operating Prohibitions

To protect against property loss, bodily injury, or death, observe the following safety instructions:

  1. Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where wireless communication equipment is completely prohibited.

Important Tips

To make better use of the product, observe the following instructions:

  1. Do not use any unauthorized or damaged accessory.
  2. Keep the product at least 2.5 centimeters away from your body during transmission.
  3. Do not keep the product receiving at high volume for a long time.
  4. For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
  5. Keep the product and its accessories out of reach of children and pets.
  6. Operate the product within the specified temperature range.
  7. Continuous transmission for a long time may lead to heat accumulation. Allow it to cool.
  8. Handle the product with care.

2.4 Precautions for Batteries

Charging Prohibitions

To protect against property loss, bodily injury, or death, observe the following safety instructions:

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  2. Do not charge a wet battery. Dry it with a soft, clean cloth prior to charging.
  3. Do not charge a battery suffering deformation, leakage, or overheating.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge shall always be prohibited as it may shorten battery life.
  7. Do not disassemble, modify, or repair the product and its accessories without authorization.

Maintenance Instructions

To help your battery work normally or prolong its life, observe the following instructions:

  1. Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
  2. It is recommended to charge the battery under 5℃~40℃. Violation of this limit may cause battery life reduction or leakage.
  3. To charge a battery attached to the product, turn it off to ensure a full charge.
  4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time, nor place it close to other heating sources.
  7. Do not squeeze and penetrate the battery, nor remove its housing.

Transportation Instructions

  1. Damaged batteries must not be transported.
  2. To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  3. The radio must be switched off and secured against switch-on if the battery is attached.

3. Setup and Installation

3.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. Initial charging or charging after extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. For best performance, fully charge/discharge the battery two or three times.

WARNING! When keys, ornamental chain, or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

How to Charge (Type-C USB and Desktop Charger)

This radio supports two charging methods: Type-C USB charging and desktop charging (desktop charger not included).

  1. Desktop Charging:
    1. Plug the AC adaptor into the AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange, ready to charge.
    2. Plug the battery or the radio into the charger. Ensure good contact. The indicator light turns red.
    3. Charging takes approximately 2-5 hours. When the lamp lights green, charging is complete. Remove the battery or radio.
    4. If charging a radio (with battery) while powered on, the indicator may not turn green to show full charge. The radio consumes energy when powered on, affecting accurate voltage detection.
  2. Type-C USB Charging:
    1. Ensure your radio is turned OFF.
    2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet.
    3. An empty battery will be fully charged in 4 hours.
    4. The battery meter on the LCD will move to indicate charging.
    5. It is recommended to power OFF your radio while charging. If powered on, you may not be able to transmit if the battery is completely empty. Allow time for the battery to charge to 1 bar before transmitting.
    6. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio connected to the charger.

LED Indicator Status

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

NOTE: Trouble means battery too warm, battery short-circuited, or charger short-circuited.

How to Store the Battery

  • If the battery needs to be stored, keep it at 80% discharged.
  • It should be kept in a low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.
  • Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
XHDATA E-100 Type-C Fast Charging
Figure 3: Type-C Fast Charging for XHDATA E-100.

3.2 Installing/Removing the Antenna

  1. Installing: Align the antenna with the antenna port. Rotate clockwise until fully tightened.
  2. Removing: Rotate the antenna counterclockwise until completely detached.

3.3 Installing the Belt Clip

  1. Align the grooves of the belt clip with those of the radio and push down until you hear a click.
  2. To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide the clip upward.

3.4 Installing the Battery Pack

NOTICE: When removing the battery, ensure that the radio is turned off.

  1. Before attaching or removing the battery, turn the power/volume knob all the way counter-clockwise to turn off the radio.
  2. Ensure the battery is aligned parallel with the radio body, with the lower edge about 1-2cm below the radio's edge.
  3. Once aligned with the guide-rails, slide the battery upward until you hear a click as it locks in place.

Removing the Battery Pack

To remove the battery, press the battery release above the battery pack as you slide the battery downward.

3.5 Installing the Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

4. Radio Overview

4.1 Buttons and Controls of the Radio

XHDATA E-100 Detailed View of Buttons and Ports
Figure 4: Detailed view of XHDATA E-100 buttons and ports.
  1. Antenna
  2. LED flashlight
  3. Status LED
  4. Power / Volume knob
  5. Battery release latch
  6. PTT - Push to talk
  7. SK1-Programmable key (flashlight/alarm switch)
  8. SK2-Programmable Key (Radio/Monitor)
  9. Accessory jack
  10. Type-C charging indicator
  11. V/M-VFO/MR mode key
  12. A / B select key
  13. SWEEP key
  14. MENU Key
  15. Type-C charging port
  16. Color LCD
  17. Speaker
  18. Microphone
  19. EXIT Key
  20. Keypad

4.2 LCD Display Icons

IconDescriptionIconDescription
MxxxMemory channelDWDual watch enabled
VFOFrequency ModeTXTransmitting
VOXVOX enabledRXReceiving
CTCCTCSS enabledRReverse function enabled
DCSDCS enabled►Indicates active band or channel
NNarrowband enabled+/-Frequency shift direction if enabled in VFO
H/LTransmit power level indicator (High/Low)Battery level indicator
Squelch Open/Close Indicator

4.3 Status Indications (LED)

The status LED has a very simple and traditional design:

LED IndicatorRadio Status
Constant RedTransmitting
Constant GreenReceiving

The LED is off in standby mode.

4.4 Main Keypad Controls

  • V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode: CH/FREQ/NAME.
  • A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/ Signal Wait/ Dual Watch off modes.
  • One-Touch Search Key: Short press to enter One-Touch search key.
  • EXIT: Short press to return to menu or previous menu. Press and hold to enter frequency sweep mode.
  • #: Long press to lock or unlock the keypad.
  • *: Short press to enter DTMF dial. Press and hold to scan on and scan off.
  • 0[space]: Press and hold to enter weather switch to select weather channel.
  • [MENU] key: Activates the MENU, selects MENU items, and confirms parameters.
  • ▲/▼ keys: Press for more than 2 seconds to move channel/frequency rapidly upwards/downwards. In SCAN mode, moves scanning upwards/downwards.

4.5 Programmed Key Functions (SK1, SK2)

It is possible to set different functions for [SK1] and [SK2] keys via Menu 48/49/50 (PF1 Press/PF1 LongPre/PF2 Press).

FunctionDescription
NoneNo function
Torch On/OffQuick switch torch (flashlight)
Power SelectQuickly switch between high, low transmit power
Scan On/OffQuickly switch scanning function on or off
VOX On/OffQuickly switch on/off VOX function
Alarm on/offQuickly establishes an emergency call
Radio on/offQuickly switch on or off the FM radio function

5. Basic Operations

5.1 Power On/Off the Radio

To turn the unit on, rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD for about one second, then display a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".

To turn the unit off, rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".

  • Voice Prompt Setting: Press [MENU] to enter Menu >> 30 VOICE.
  • Power On Type Setting: Press [MENU] to enter Menu >> 34 Power On Typ to select Picture, Message, Voltage.
  • If a power-on password is set, you need to enter the correct password. Press [MENU] to enter Menu >> 37 Power-on PWD.

5.2 Adjusting the Volume

To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off.

By using the monitor function (enabled from the [FM broadcast/Monitor] key below the PTT), you can more easily adjust your volume by adjusting it to the un-squelched static.

5.3 Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.

Press and hold the [A/B] key to quickly switch Double Wait/ Signal Wait.

5.4 VFO/Channel Switch

Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display.

  • In channel mode (MR), the channel number will be displayed on the left.
  • In frequency mode (VFO), 'VFO' will be displayed on the left.

In MR mode, press and hold the [V/M] key to switch the frequency, channel, and name display mode of the channel.

5.5 Frequency (VFO) Mode

In Frequency (VFO) mode, you can navigate up and down the band using the ▲/▼ keys. Each press will increment or decrement your frequency according to the frequency step you've set. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.

WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offense. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules, and regulations apply to your area.

The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to use in VFO mode and allows manual input of these frequencies. Prohibit use in channel mode.

5.6 Channel (MR) Mode and Channel Selection

There are two modes of operation: Frequency (VFO) mode and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is more practical. Frequency (VFO) mode is handy for experimentation and programming channels into memory.

In Channel (MR) mode, you can navigate up and down the channel using the ▲/▼ keys or the encoder.

Press the [V/M] key to switch the radio between VFO and Channel mode, select Channel mode.

  1. Operation 1: Press the ▲/▼ navigation key to select the channel.
  2. Operation 2: Input the channel numbers by the keyboard. For example, to switch to channel 12, input [0][1][2].

When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.

5.7 Making a Call

NOTE: Press the [A/B] key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press [V/M] key to switch between frequency (VFO) mode and channel (MR) mode.

  • Channel Mode Call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on.
  • Frequency Mode Call: Press [V/M] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on.
  • Receive a Call: When you release the [PTT] key, you can answer without any action. When receiving a call, the green LED will be on.

NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.

5.8 Using the Flashlight

You can use the radio's high-intensity LED flashlight by pressing the [SK1] key.

  1. Press [SK1] key once for continuous illumination (Always On mode).
  2. Press [SK1] key again for Strobe Light (emergency signal) mode.
  3. Press [SK1] key a third time to turn the light off.
XHDATA E-100 Flashlight Function
Figure 5: XHDATA E-100 flashlight in various environments.

5.9 Emergency Alert

The Emergency Alert feature can be used to signal members in your group for help.

To activate, press and hold the [SK1] key for 3 seconds. The radio will send a loud siren sound and the flashlight will flash.

Press the [SK1] key to exit the emergency alert function.

WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.

5.10 FM Radio

The frequency range to listen to the radio is 65-108MHz.

  1. In frequency or channel mode, press [SK2] key to turn on the radio.
  2. Select the desired radio frequency with the ▲/▼ keys or input the frequency.
  3. Press #z to automatically search a radio station.
  4. Press [SK2] key to exit FM radio.

NOTE: While listening to the radio, the frequency or channel of A/B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will automatically switch again to FM radio mode.

5.11 Monitor

In standby, press and hold the [SK2] key to enter Monitor. This function allows monitoring weak signals when receiving a matched carrier but the signaling or signal is too weak.

Stop pressing the [SK2] key to turn off the speakers and return to standby mode.

If no signal, it will emit noise when you press the [SK2] Key.

5.12 Keypad Lock

The radio features a keypad lock that locks out all keys except for the three side keys.

To enable or disable the keypad lock, press and hold the # key for about two seconds.

You can also enable the radio to automatically lock the keypad after ten seconds from the menu.

5.13 Frequency Reversal

A short momentary press of the * key enables the reverse function. If you want to listen to the repeater's input frequency instead, press the * key momentarily, and you'll reverse your transmit and receive frequencies. This is indicated on the LCD with an 'R' in the top row, next to the +/- for the offset direction.

5.14 TX Repeaters Tone

Press [PTT] + [SK2] key to send a 1750Hz repeaters tone. This function is useful for communications through repeaters. If the keypad lock is enabled, you can still send a 1750Hz tone the regular way without unlocking the radio.

  1. The radio will act as a receiver. Press and hold the * key, and the screen will display “SEARCH SWEEK...”.
  2. If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed; otherwise, NONE is displayed.
  3. You can press the [MENU] key to save the Search frequency and CTCSS or DCS to the channel.

NOTE: During frequency Search, press the #z key on the radio to switch between UHF or VHF bands.

5.16 Weather Radio/Scan Weather Channel (NOAA)

Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations, and a NOAA Weather Scan function to scan all 10 channels of the NOAA Weather Radio.

  1. To turn the NOAA Weather Scan on, press the [OSQL] key for 3 seconds; a NOAA icon will appear. The radio will go to Weather band mode.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the #z key for 3 seconds during a NOAA weather scan will stop the scan.
  3. After stopping NOAA weather scan, you can manually select the weather channel by pressing the ▲/▼ key.
  4. To exit the Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.

Weather Channel Frequencies and Names

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

6. Advanced Features

6.1 Working the Menu System

Basic Use with Arrow Keys

  1. Press the [MENU] key to enter the menu.
  2. Use the ▲/▼ keys to navigate between menu items.
  3. Once you find the desired menu item, press [MENU] again to select it.
  4. Use the ▲/▼ keys to select the desired parameter.
  5. To confirm your selection, press [MENU] to save and return to the main menu. To cancel changes, press [EXIT] to reset and exit the menu.
  6. To exit the menu at any time, press the [EXIT] key.

Using Short-Cuts

Every menu item has a numerical value associated with it for direct access. The menu is organized with the ten most common functions on top.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] key.
  4. For entering the desired parameter, you can use the arrow keys or the numerical keypad to enter the short-cut code.
  5. To confirm your selection, press [MENU] to save and return to the main menu.

6.2 Scanning

The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited while scanning.

To enable the scanner, press and hold the * key for about two seconds. Press and hold the * key to exit scanning mode.

6.2.1 Scanning Modes

The scanner is configurable to one of three ways of operation: Time, Carrier, or Search.

Setting Scanner Mode:

  1. Press the [MENU] key to enter the menu.
  2. Enter 19 on your numeric keypad to access scanner mode.
  3. Press the [MENU] key to select.
  4. Use the ▲/▼ keys to select scanning mode.
  5. Press the [MENU] key to confirm and save.
  6. Press the [EXIT] key to exit the menu.
  • Time Operation (TO): Scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
  • Carrier Operation (CO): Scanner stops when it detects a signal, and after a factory preset time with no signal, it resumes scanning.
  • Search Operation (SE): Scanner stops when it detects a signal. To resume scanning, you must press and hold the * key again.

6.2.2 Frequency Scanning

  1. In frequency mode, press the * key for more than 2 seconds. The radio will start scanning.
  2. You can change the scanning direction with the ▲/▼ keys.
  3. Press the * key to stop the scanning.

6.2.3 Channel Scanning

  1. In channels mode, press the * key for more than 2 seconds. The radio will start scanning.
  2. You can change the scanning direction with the ▲/▼ keys.
  3. Press the * key to stop the scanning.

6.2.4 Scan CTCSS

This function allows scanning frequencies with CTCSS tone enabled.

  1. In standby mode, press [MENU] [1][6]. “Scan CTCSS” will appear.
  2. Press [MENU] key and the scan of CTCSS tones will start.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.

6.2.5 Scan DCS

This function allows scanning frequencies with DCS code enabled.

  1. In standby mode, press [MENU] [1][7]. The display will show “Scan DCS”.
  2. Press [MENU] key and the scan of DCS codes will start.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.

6.3 Manual Programming (Channels Memory)

Memory channels are an easy way to store commonly used frequencies. The radio features 999 memory channels that can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier or channel name.

Frequency Mode vs. Channel Mode

  • Frequency Mode (VFO): Used for temporary frequency assignments, such as a test frequency or quick field programming.
  • Channel Mode (MR): Used for selecting preprogrammed channels.

Example 1: Programming a Channel Repeater Offset with CTCSS Tone

EXAMPLE: New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz (This is a (+ 5) Offset), TX CTCSS tone 123.0

  1. Press the [EXIT] key to switch between menus.
  2. Press [V/M] key to set the radio to VFO mode (VFO icon displayed).
  3. [MENU] [1][4] [MENU] [1][0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
  5. Enter RX frequency (Ex. 43255000)
  6. [MENU] [1][3] [MENU] [1][0] [MENU] -->>[EXIT] (Enter the desired channel 10, RX has been added)
  7. Enter TX frequency (Ex. 43755000)
  8. [MENU] [1][3] [MENU] [1][0] [MENU] -->> [EXIT] (Enter the same channel 10, TX has been added)
  9. Press [V/M] key to return to the MR mode and the channel number will reappear.

Example 2: Programming a Simplex Channel with CTCSS Tone

EXAMPLE: New memory in Channel 10: RX = 432.6625 MHz, TX CTCSS tone 123.0

  1. Press the [EXIT] key to switch between menus.
  2. Press [V/M] key to set the radio to VFO mode (VFO icon displayed).
  3. [MENU] [1][4] [MENU] [1][0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Select desired TX encode tone)
  5. Use [EXIT] to select Upper display.
  6. Enter RX frequency (Ex. 43266250)
  7. [MENU] [1][3] [MENU] [1][0] [MENU] -->> [EXIT] (Enter the desired channel 10, Channel has been added)
  8. Press [V/M] key to return to the MR mode and the channel number will reappear.

6.4 Repeaters Programming

These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use them.

  1. Press [V/M] key to set the radio to VFO mode (VFO icon displayed).
  2. Use the numeric keypad to enter the repeater's output (your receiving) frequency.
  3. Press the [MENU] key to enter the menu.
  4. Enter [1][2] on the numeric keypad to get to frequency offset.
  5. Press [MENU] key to select.
  6. Use the numerical keypad to enter the specified frequency offset. See “12 OFFSET - Frequency shift amount” for details.
  7. Press [MENU] key to confirm and save.
  8. Enter [1][1] on the numeric keypad to get to offset direction.
  9. Use the ▲/▼ keys to select + (positive) or - (negative) offset.
  10. Press [MENU] key to confirm and save.
  11. Optional:
    1. Save to memory (see “Manual programming” for details).
    2. Set up CTCSS (see “CTCSS” for details).
  12. Press [EXIT] key to exit the menu. If everything went well, you should be able to make a test call through the repeater.

NOTE: If you're experiencing problems, check your settings or repeat the procedure. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open the repeater. To see how this is done, refer to “1750Hz Tone-burst”. If you're still unable to connect, contact the person in charge of the radio system or your local amateur radio club.

6.5 VOX (Voice Activated Transmit)

This function allows hands-free conversations. Speak into the microphone, and communication will be automatically activated.

  1. In standby mode, press [MENU] + 25. The screen will display “VOX Switch”.
  2. Press [MENU] key to enter the function. Press the ▲/▼ keys to turn off/on the VOX function.
  3. In standby mode, press [MENU] + 26. The screen will display “VOX Level”.
  4. Press [MENU] key to enter the function. Press the ▲/▼ keys to select the VOX level (1-9), then press [MENU] key to confirm.
  5. To return to standby mode, press [EXIT] key.

NOTE: Level 1 is the least sensitive, while level 9 is the most sensitive. When the radio is in Scan or FM Radio mode, VOX is not enabled.

6.6 Dual Watch

The ability to monitor two channels at once can be a valuable asset. This can be achieved by having one receiver flip-flop between two frequencies at a fixed interval (Dual Watch).

The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.

Enabling or Disabling Dual Watch Mode

  1. Press the [MENU] key to enter the menu.
  2. Enter 38 on the numeric keypad to get to Dual Watch.
  3. Press [MENU] key to select.
  4. Use the ▲/▼ keys to select Double Wait/ Signal Wait/ OFF.
  5. Press [MENU] key to confirm.
  6. Press the [EXIT] key to exit the menu.

6.7 Stopwatch Timer

In standby mode, press [MENU] + 57. The screen displays “STOP WATCH”.

To enter the function, press the ▲/▼ keys to enable (ON), then press [MENU] key for confirmation. To return to standby mode, press [EXIT] key.

Using the Stopwatch Timer:

When ON, press [MENU] key to start counting; press [MENU] key again to re-start counting. To exit, stop counting first, then press [EXIT] key.

6.8 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals. In two-way radio systems, DTMF is commonly used for automation systems and remote control, such as activating amateur radio repeaters.

DTMF Frequencies and Corresponding Codes

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

The radio has a full implementation of DTMF, including A, B, C, and D codes. The numerical keys, as well as the *, and # keys, correspond to the matching DTMF codes. A, B, C, and D codes are located in the [MENU], ▲/▼, and [EXIT] keys respectively.

To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key. If the keypad lock is enabled, you can still send DTMF tones.

6.9 Customization

The radio allows you to define visual and audible features such as Display Illumination Time, MR/Channel Mode Display Format, Power On Message, Power On password, Keypad Beep, Roger Beep, Voice Prompt, etc.

6.9.1 Display Backlight (ABR) - MENU 51

In standby mode, press [MENU] + 51. The screen will display “ABR”.

Press [MENU] key to enter the function. Press the ▲/▼ keys to select the always on/required delay time (ON/5sec/10sec/15sec/20sec) for the backlight, then press [MENU] key to confirm. To return to standby mode, press [EXIT] key.

6.9.2 Beep PROMPT (BEEP) - MENU 32

If enabled, every time a key is pressed, you will hear a Beep tone.

In standby mode, press [MENU] + 32. The screen will display “BEEP PROMPT”.

Press [MENU] key to enter the function. Press the ▲/▼ keys to turn ON/OFF the beep function. Press [MENU] key to confirm and exit to return to standby mode.

6.9.3 Voice Function (VOICE) - MENU 30

In standby mode, press [MENU] + 30; the screen will display “VOICE”.

Press [MENU] key to enter the function. Press the ▲/▼ keys to select OFF/ON. Confirm your selection by pressing MENU. To return to standby mode, press [EXIT] key.

6.9.4 Language of the MENU (LANGUAGE) - MENU 29

This section shows the language of the MENU (English).

In standby mode, press [MENU] + 29. The display will show “LANGUAGE”.

6.9.5 Working Mode (MDF-A) - MENU 39

The radio has four working modes: Frequency mode (FREQ), Channel mode (CH), Channel name (NAME).

To shift from one mode to another: In Standby mode, press [MENU] + 39; select the desired working mode with the ▲/▼ keys. Press [MENU] key again to confirm your selection.

6.9.6 Roger Beep, End Transmission Tone (ROGER) - MENU 33

Roger Beep can be enabled/disabled:

  • OFF: Roger Beep disabled
  • BEEP: Roger Beep tone at the end of transmission

In standby mode, press [MENU] + 33; the screen will display “ROGER”.

Press [MENU] to enter the function. Press the ▲/▼ keys to select OFF/ON. Confirm your selection by pressing [MENU] key. To return to standby mode, press [EXIT] key.

6.9.7 Power On Message (POWER ON MSG) - MENU 40

You can customize the welcome message that appears on the display when the radio is switched on.

Choose among the following options:

  • VOLTAGE (power voltage momentarily displayed)
  • MESSAGE (welcome message)
  • LOGO (Custom Pictures)

In Standby mode, press [MENU] + 40. The display will show “POWER ON MSG”.

Press [MENU] key to enter the function. Press the ▲/▼ keys to select the desired option and confirm with MENU. To return to standby mode, press [EXIT] key.

6.9.8 Power On Password (Power On PWD) - MENU 37

You can request the correct password when the radio is turned on.

In standby mode, press [MENU] + 37. The display will show "POWER ON PWD".

Press [MENU] key to enter the function. Press the ▲/▼ keys to enable/disable (ON/OFF) the power on password and confirm with MENU. To return to standby mode, press [EXIT] key.

Enable the power on password function. Each time the radio is turned on, it will display "Input Password" to prompt for the correct password. The default startup password is 000000.

6.9.9 Reset - MENU 56

This transceiver has two Reset modes: VFO and ALL.

  • Reset VFO: All settings except channels will return to the default settings.
  • Reset ALL: All settings will return to the default settings.

Reset VFO: In standby mode, press [MENU] + 56; the screen will display “RESET”. Press [MENU] to enter the function. Press the ▲/▼ keys to select VFO, then press [MENU] to confirm. The display will show “Sure to reset?”. Press [MENU] again to confirm, and the transceiver will turn off and reboot.

Reset ALL: In standby mode, press [MENU] + 56. The screen displays “RESET”. Press [MENU] to enter the function. Press the ▲/▼ keys to select ALL, then press [MENU] to confirm. The display will show “Sure to reset?”. Press [MENU] again to confirm; the transceiver will turn off and reboot.

7. Maintenance

7.1 General Care

  • Keep the radio clean and dry. Wipe with a soft, damp cloth. Do not use harsh chemicals or solvents.
  • Avoid extreme temperatures, direct sunlight, and high humidity.
  • Do not drop or subject the radio to severe impacts.
  • Ensure all covers and caps are properly sealed to prevent dust and moisture ingress.

7.2 Battery Maintenance

Refer to section 2.4 "Precautions for Batteries" for detailed charging, maintenance, and storage instructions to ensure optimal battery life and safety.

8. Troubleshooting Guide

If you encounter problems with your XHDATA E-100, refer to the table below for possible solutions. If the issue persists, contact technical support.

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent.The battery voltage maybe low.
The volume level may be low.
The antenna maybe loose or maybe installed incorrectly.
The speaker maybe blocked.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, then remove and reattach the antenna.
Clean the surface of the speaker.
You cannot communicate with other group members.The frequency or signaling type maybe inconsistent with that of other members.
You may be too far away from other members.
You may be interrupted by radios using the same frequency.
Verify that your TX/RX frequency and signaling type are correct.
Move towards other members.
Change the frequency, or adjust the squelch level.
You hear unknown voices or noise.The radio in analog mode maybe set with no signaling.Request your dealer to set signaling for the current channel to avoid interference.
You are unable to hear anyone because of too much noise and hiss.You may be too far away from other members.
You may be in an unfavorable position (e.g., blocked by high buildings or underground areas).
It may be the result of external disturbance (electromagnetic interference).
Move towards other members.
Move to an open and flat area, restart the radio, and try again.
Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.

9. Technical Specifications

ParameterSpecification
Frequency bandFM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx);
Memory channels999
Power supplyLi-Ion battery 7.4V/3000 mAh
Operating temperature-10°C to + 45°C
Working modemonoband/dualband
ModulationF3E(FM)
Max. frequency deviation≤ ±5KHz
Spurious radiation< -60dB
Frequency stability±2.5 ppm
Rx sensitivity< 0.2uV
Audio output power≥ 500mW
Dimensions64x121x35mm (LxAxP)
Weight240g

Specifications are subject to change without notice.

WARNING: Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.

10. User Tips

  • Regulatory Compliance: For radio amateurs in regions like Brazil (ANATEL), the presence of an FCC ID on the radio may facilitate the approval process. However, always verify local regulations and complete necessary homologation procedures.
  • Performance: The XHDATA E-100 is noted by users for its flawless operation.

11. Warranty and Support

For technical support, warranty inquiries, or any other questions, please contact XHDATA through the following channels:

  • Skype: radiwow
  • TikTok: XHDATAradio
  • YouTube: Xhdata Radio
  • Facebook: Xhdata Radios
  • Web: www.xhdata.com.cn
  • Whatsapp: +86 18025193267
  • E-mail: xhdatacn@gmail.com

A detailed user manual in PDF format can also be found at: XHDATA E-100 User Manual (PDF)

Disclaimer: The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With continuous technological development, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without prior written authorization.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.