DEKO DKRT170Y1

Contents

DEKO Rotary Tool Kit Instruction Manual

Model No.: DKRT170Y1 / DKRT170Y1P

Brand: DEKO

Important Safety Warnings

▲ WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

  • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
  • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
  • Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4) Power tool use and care

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
  • Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Product Overview

The DEKO Rotary Tool Kit is a versatile power tool designed for various applications such as carving, cutting, sanding, grinding, polishing, and engraving. It features a powerful 170W motor, 6-speed adjustment, and an ergonomic design for comfortable use.

DEKO Rotary Tool Kit with various accessories
The DEKO Rotary Tool Kit, including the main unit, flexible shaft, and a wide array of accessories.
DEKO Rotary Tool with labeled parts: ON/OFF switch, 6-speed variable gear, spindle lock, and external brush cover.
Key components of the DEKO Rotary Tool: ON/OFF switch, 6-speed variable gear, spindle lock, and external brush cover.

Parts Description

  1. On/Off Switch
  2. Speed Dial
  3. Carbon Brush
  4. Shaft Lock Button
  5. Collet
  6. Collet Nut
  7. Union Nut
  8. Louvers
  9. Hanger
Diagram showing the rotary tool and a comprehensive list of included accessories for sanding, grinding, drilling, carving, cutting, cleaning, and polishing.
A detailed view of the rotary tool and its extensive set of accessories for various applications.

Specifications

AttributeValue
Brand NameDEKO
Model NumberDKRT170Y1
Rated Input Power170W
No-Load Speed8000-35000rpm
Frequency50/60Hz
Rated Voltage220V
Power SourceAC
Drill TypeMini Drill
ApplicationFor Carving, Cutting, Sanding, Grinding, Polishing, Engraving
UseHome DIY
Weight1.84kg
Battery IncludedYes (for accessories, not main unit)
Collet Size3.2mm (1/8")
Cable Length1.8m
Protection ClassII

Setup

Changing Collets

▲ WARNING: Always unplug the tool before changing accessories, changing collets or service the tool.

  1. Press the shaft lock button (4), hold down and rotate the shaft by hand until it engages the shaft lock. Do not engage the shaft lock button while the rotary tool is running.
  2. With the shaft lock button engaged, loosen and remove the collet nut (6). Use the collet wrench if necessary.
  3. Remove the collet by pulling it free from the shaft.
  4. Install the appropriate size collet fully into the shaft and replace the collet nut on the shaft. Do not fully tighten the nut when there is no bit or accessory installed.

Installing Accessories

▲ WARNING: Always unplug the tool before changing accessories, changing collets or service the tool.

  1. Press the shaft lock button (4) and rotate the shaft by hand until it engages the shaft lock. Do not engage the shaft lock button while the rotary tool is running.
  2. With the shaft lock button engaged, loosen (do not remove) the collet nut (6). Use the collet wrench if necessary.
  3. Insert the bit or accessory shank fully into the collet.
  4. With the shaft lock button engaged, tighten the collet nut with the provided wrench until the accessory shank is gripped by the collet. Avoid over-tightening of the collet nut.

▲ WARNING: If you are changing an accessory immediately after use, be careful not to touch the collet, collet nut, or accessory as they may be hot.

Attaching the Flexible Shaft

Step-by-step guide to attaching the flexible shaft to the rotary tool.
Follow these steps to easily attach the flexible shaft for detailed work.
  1. Turn and remove the umbrella cover from the rotary tool.
  2. Insert the shaft inside the flexible shaft into the collet nut.
  3. Fix the flexible shaft hole with the spanner.
  4. Secure the end of the flexible shaft to the front of the rotary tool.
  5. Locking the flexible shaft head with the spanner and L-PIN.

Operating the Rotary Tool

General Operation

Before starting, please determine the best grip for your job. The rotary tool can be held like a pencil for fine work, or gripped around the body when less precision is needed. Practice on scrap material to determine the best speed, correct accessory, and get a feel for the job.

  1. Do not press the accessory into the workpiece. Little or no operator force should be needed when the correct accessory and speed are used. Touch the accessory to the workpiece and guide it over the work, making multiple passes when necessary.
  2. Secure the work piece in a vise or clamp to a workbench to prevent it from moving under the tool.
  3. Hold the tool in front and away from you, keeping the tool accessory clear of the workpiece.
  4. Turn on the tool and let the motor and accessory build up to full speed.
  5. Lower the tool gradually until the accessory contacts the workpiece.
  6. Move the tool continuously at a steady, consistent pace.
  7. Use just enough pressure to keep the tool from chattering or bouncing.

NOTE: Heavy pressure will decrease the tool's speed and put a strain on the motor.

  1. Lift the tool away from the workpiece before turning off the tool.

Applications

Examples of rotary tool applications including sanding, carving, cutting, polishing, and drilling.
The rotary tool is suitable for a wide range of applications.
FunctionAccessoryApplication
DrillingDrill bitWood applications
MillingMilling bitVarious applications: e.g., recessing, hollowing out, shaping, grooving, or making slots
EngravingEngraving bitsMarking
Polishing, rust removalMetal brush, Polishing toolsProcessing various metals and plastics, particularly precious metals such as gold or silver
CleaningPlastic brushes, Metal brushe.g. cleaning hard to reach plastic housings or cleaning the area around a door lock; rust removal
GrindingGrinding discs, Grinding stone, Grinding bitsGrinding stone, detail work on hard materials such as ceramics or alloy steel
CuttingCutting discsProcessing metal, plastic

Product Demonstration Video

Watch a demonstration of the DEKO Rotary Tool in action, showcasing various applications and accessory changes.

Maintenance

Cleaning and Maintenance

Clean dust and debris from vents. Keep handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean, since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Never use flammable or combustible solvents around tools.

Troubleshooting

If the tool is not operating as expected, first check the power connection and ensure the ON/OFF switch is in the 'ON' position. Verify that the collet nut is securely tightened and the correct accessory is installed. If the issue persists, refer to the 'Service Information' section for support.

User Tips

  • For delicate work, especially with the flexible shaft, use lower speeds (1-3) for better control.
  • When working on hard materials like ceramic tiles, ensure you use appropriate cutting discs and apply light, consistent pressure.
  • To prolong the life of the tool, avoid over-tightening accessories and ensure proper ventilation during extended use.
  • The flexible shaft is highly recommended for precision tasks like engraving and detailed carving, as it significantly reduces vibration.

Warranty and Support

Service Information

This tool is warranted to the original purchaser to be free from defect in materials and workmanship for a period of 2 years from the original purchase date.

If the tool should fail some day in spite of our quality controls and materials, only have it repaired by an authorized electrician or contact your local distributor or service agent.

You can also contact us by emails: services@dekotools.com, support@dekotools.com

The warranty will not apply to the following cases:

  • where this product has been subjected to misuse, abuse, accident or want of care;
  • where this product has been used for a purpose for which it was not designed or is not suited;
  • where the service of this product has been undertaken by a non-authorised person or company or if non-approved parts have been used.
  • components that are subject to natural wear and tear caused by use in accordance with operating instructions.

For additional guidance, you may refer to the official user manual PDF: DEKO Rotary Tool User Manual (PDF)

Disposal

The machine and packaging should be sorted for environmental-friendly recycling. Do not dispose of power tools into household waste! Please recycle them at collection points provided for the purpose. Ask your local authority for information about recycling.

Symbols Explanation

SymbolExplanation
CEConforms to relevant legislation and safety standards.
FCConforms to FCC relevant legislation and safety standards.
▲To reduce the risk of injury, user must read instruction manual.
🗑️Do not dispose of old applications with domestic rubbish.
☐Double insulation. Class II device. The device must not be earthed.
👓Wear eye protection.
😷Wear respiratory protection.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.