YESPER MONSTER START-N1

Contents

YESPER MONSTER START-N1

12V/24V 6000A Car Jump Starter User Manual

Important Safety Warnings

Please read all instructions carefully before using this product. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.

  • This product is designed for 12V or 24V vehicle engine starting only. Using it for other voltage platforms may cause damage or danger.
  • DO NOT use if battery clamps or cables are damaged.
  • This product is not a replacement for a vehicle battery.
  • Ensure vehicle battery terminals are clean and clamps are properly connected before use. Dirty or corroded terminals can affect performance.
  • DO NOT crank the engine for more than 3 seconds at a time. The jump start feature is for short-term operation only. Exceeding 3 seconds may damage the unit. Allow the jump starter to cool for at least 2 minutes after each cranking.
  • Remove battery clamps immediately after successful engine start to prevent damage.
  • Always connect red clamp to positive (+) terminal and black clamp to negative (-) terminal.
  • NEVER allow red and black clamps to touch each other or any metal object.
  • This product is for adult use only. Keep out of reach of children.
  • DO NOT expose to rain, snow, or damp conditions. NEVER submerge in water.
  • DO NOT operate in explosive environments (flammable liquids, gases, dust).
  • DO NOT modify or disassemble the product.
  • Remove all metal items (watches, necklaces, rings) before using.
  • DO NOT operate if the unit has been dropped, received a sharp blow, or is otherwise damaged. It must be tested by a qualified battery technician.
  • DO NOT place the product in environments exceeding 60°C (140°F).
  • Charge only at ambient temperatures between 0°C (32°F) and 45°C (113°F).
  • Use only the original charger.
  • If the unit leaks liquid, dispose of it at a proper recycling facility immediately.
  • Always wear eye protection when working with batteries. Batteries can explode and cause flying debris.
  • If battery acid contacts eyes, flush with running water for at least 15 minutes and seek medical attention.
  • If battery acid contacts skin, rinse with water and wash thoroughly with soap. Seek medical attention if redness, pain, or irritation occurs.
  • Ensure someone is nearby to assist in an emergency.
  • Dispose of lithium battery products according to local regulations.

Product Layout and Components

Familiarize yourself with the components of your YESPER MONSTER START-N1 jump starter.

YESPER MONSTER START-N1 labeled diagram

Image: Labeled diagram of the YESPER MONSTER START-N1 showing all ports and controls.

  1. Battery Clamps
  2. LED Flashlight
  3. Battery Level Indicator
  4. Warning Light
  5. 12V Mode Indicator
  6. 24V Mode Indicator
  7. Flashlight Button
  8. 12V Override Button
  9. 24V Override Button
  10. 29V5A DC Input Port
  11. USB-C QuickCharge 2.0 Input Port
  12. USB-A Output Ports

What's in the Box

Contents of YESPER MONSTER START-N1 box

Image: Contents of the product box including the jump starter, user manual, charge adapter, and USB-A to USB-C cable.

  • 1 x YESPER MONSTER START-N1 Jump Starter
  • 1 x User Manual
  • 1 x 29V AC Charge Adapter
  • 1 x USB-A to USB-C Cable

Setup and Charging

Initial Charging

Before first use, fully charge your YESPER MONSTER START-N1. It can be fully charged in approximately 1 hour using the included AC adapter.

Jump starter charging via wall adapter

Image: The jump starter connected to a wall outlet via its 29V AC adapter for charging.

  • Fast Charge: Connect the included 29V AC adapter to the unit's 29V DC input port.
  • Slow Charge: Connect a USB-C cable (not included) to the unit's USB-C input port, then connect the other end to a powered USB port (e.g., USB wall charger, USB car charger).
  • The two input ports do not support simultaneous charging; the 29V DC input takes priority.
  • Charge only at ambient temperatures between 0°C (32°F) and 45°C (113°F).

Operating Instructions

Battery Status

Press any button to illuminate the internal Battery Level Indicator LEDs, showing the current battery capacity.

Jump starter with battery level indicators and charging ports

Image: The jump starter displaying battery level indicators (25%, 50%, 75%, 100%) and its USB and DC input/output ports.

Battery Level IndicatorBattery Level
25% LED Flashing0%
1 LED solid On≤25%
2 LEDs solid On≤50%
3 LEDs solid On≤75%
4 LEDs solid On≤100%

USB Power Output

The unit features two USB-A output ports (5V 2.4A / 5V 1A) and a USB-C input port, ideal for charging portable electronic devices.

  1. Connect your device(s) to the USB output port(s) using a compatible USB charge cable.
  2. Press any button on the unit to turn it on and activate USB power.

LED Flashlight

Press the flashlight button to activate the integrated ultra-bright LED flashlight. Continue pressing the button to cycle through the 4 modes: 100% brightness > Strobe > SOS > Off.

Jump starter LED flashlight modes

Image: The jump starter's LED light demonstrating Stable, Strobe, and SOS modes, useful for rescue, camping, night walking, and household lighting.

Jump Starting a Vehicle

Do not attempt to jump start if the jump starter's battery level is at 25% or below.

This product supports both 12V and 24V vehicle systems. Always ensure the unit is in the correct mode (12V for 12V vehicles, 24V for 24V vehicles) before connecting.

Simple steps to jump start a vehicle

Image: Four-step diagram showing how to jump start a vehicle: 1. Attach clamps correctly, 2. 12V/24V lights up, 3. Start vehicle, 4. Remove clamps.

  1. Press any button to turn on the unit and check the battery level indicator. If below 25%, recharge the unit before attempting a jump start.
  2. Connect the red clamp to the POS (+) terminal of the vehicle battery.
  3. Connect the black clamp to the NEG (-) terminal of the vehicle battery.
  4. Check the 12V and 24V mode LEDs and the warning light on the unit. Proceed as follows:
LED StatusDescriptionAction
12V LED or 24V LED flashing or solid OnGood connection.Proceed with jump start attempt.
RED warning light solid OnConnection is reversed.Reconnect the clamps correctly.
12V and 24V LEDs flashing at same timeVehicle battery is low, unit cannot identify 12V or 24V system.OVERRIDE mode required. See 'Using Override Mode'.
No LEDs onNo connection detected: Poor connection or extremely low vehicle battery voltage.Check for clean, solid connection. If still no LEDs, OVERRIDE mode required. See 'Using Override Mode'.

Video: Demonstration of the YESPER MONSTER START-N1 successfully jump-starting a large truck.

Using Override Mode

The OVERRIDE feature forces the jump starter function ON, allowing you to boost deeply discharged batteries (as low as 0 volts).

CAUTION: USE OVERRIDE MODE WITH EXTREME CARE. Both spark-proof and reverse polarity protection features are disabled in this mode.

  • Pay very close attention to battery polarity.
  • DO NOT allow positive and negative battery clamps to touch or connect.
  • DO NOT connect a 12V vehicle if 24V OVERRIDE mode is activated, and vice-versa.
  • This mode uses very high current, which can cause sparks and high heat if not used properly.
  • If unsure about your vehicle's battery system (12V or 24V), seek professional help.
  • If unsure about using this mode, do not attempt and seek professional help.
  1. ENSURE CORRECT POLARITY: Red clamp to POS (+) terminal, black clamp to NEG (-) terminal.
  2. ENSURE your vehicle battery system is 12V or 24V. Press and hold the corresponding 12V or 24V Mode button for 2 seconds.
  3. The 12V LED or 24V LED will be solid on, indicating OVERRIDE mode is enabled.
  4. Proceed with jump start attempt within 30 seconds. The OVERRIDE mode is active for 30 seconds only, then the product resets.

Maintenance

  • Recharge the battery after each use.
  • For long-term storage, recharge the unit at least every 6 months to prolong battery life and keep it ready for use.
  • Store the unit in a cool, dry place away from direct sunlight and extreme temperatures.
  • Keep the unit clean and free from dust and debris.

Troubleshooting

ProblemPossible CauseSolution
Unit not active by any button pressOver-discharge protection activated.Recharge the unit. If still inactive, contact after-sales service.
Unit not rechargingNo power from AC adapter/USB port, or faulty USB cable.1. Change AC adapter/plug into different USB outlet. 2. Replace USB cable. If still not charging, contact after-sales service.
12V LED flashing/solid but cannot jump start1. Vehicle battery system is 24V but voltage dropped to 12V. 2. Mechanical issue.1. If 24V vehicle, use 24V OVERRIDE mode. 2. Seek vehicle service/professional help.
RED warning light flashingOver-temperature protection activated.Stop use and allow unit to cool down.
25%/50%/75% LEDs flashing together during rechargeInternal battery temperature too low, recharge forbidden.Move to room temperature area and recharge after battery warms up.
25%/50% or 50%/75% LEDs flashing together during rechargeAC adapter is not original or does not match unit.Use the original AC adapter to charge the unit.
25% one LED fast flashingInternal battery over-discharged.Contact after-sales service if within warranty, or purchase a new one.

Specifications

Product specifications table

Image: Table detailing the product specifications.

FeatureSpecification
ModelMONSTER START-N1
Peak Current6000A
Battery Capacity36400mAh (135Wh)
Gasoline/Diesel DisplacementALL
Weight5.7 lb (2.6 kg)
Operating Temperature-40°C ~ 60°C (-40°F ~ 140°F)
LED FlashlightYes, 3W
12 Volt Jump StartYes
24 Volt Jump StartYes
Output2 x USB-A (5V=2.4A / 5V=1A)
InputUSB-C (5V=2A, 9V=2A), DC 29V=5A
Full Charging TimeAbout 1 hour
Dimensions270 x 189 x 159.7 mm (10.63"W x 7.44"D x 6.29"H)

User Tips

  • This booster is highly effective and has been reported to start a wide range of vehicles, from Jeeps to trucks.
  • Ensure the unit is fully charged before attempting to jump start, especially in cold weather, as performance may be affected.
  • The included cigarette lighter charger can be a useful accessory for on-the-go charging (if provided).
  • Regularly check the voltage output (16.55V for 12V mode, 29V for 24V mode without load) to ensure proper function.
  • For optimal longevity, remember to recharge the unit every 6 months even if not used.

Frequently Asked Questions (FAQ)

FAQ section image

Image: Frequently Asked Questions about the jump starter.

Q: Can this product automatically identify 12V and 24V vehicle batteries?
A: Yes, under normal conditions. However, if the vehicle voltage is too low or there's no battery, you may need to activate OVERRIDE MODE manually.
Q: How many times can this product jump start a vehicle?
A: On a full charge, it can jump start a 12V vehicle about 65 times and a 24V vehicle about 40 times.
Q: How long does it take to charge this product?
A: Approximately 1 hour using the original 29V AC adapter.
Q: How many times can this product charge a phone?
A: It depends on the phone's battery capacity. For example, it can charge an iPhone 12 about 13 times.
Q: What is the lifespan of the product?
A: It can be used for 3-5 years under normal conditions.
Q: How long can the product be stored after being fully charged?
A: With patented technology, a fully charged unit can be stored for 3 years. To extend service life, it's recommended to use and recharge it every 6 months.
Q: Does it start truck batteries?
A: Yes, it is designed to start truck batteries. It has a 36,400mAh capacity.

Warranty and Support

Warranty Information

  • 12+6 Months Online After-Sales Service: Within 12 months of purchase, timely online after-sales service is provided. Register on the official store (yes-per.com) to become a member and receive an additional 6 months of service, totaling 18 months.
  • 30 Days Money Back Guarantee: Within the first 30 days after purchase, you can apply for a return through your seller if you have any issues.
  • 30 Days to 12 Months (18 Months for Member Customers): Defective units due to manufacturing issues will be replaced with a new one within 12 months. For member customers, this extends to 18 months.

Customer Service

  • 12+6 Months Limited Warranty Service
  • Lifetime Technical Service
  • Contact Us: cs@yes-per.com
  • For FAQ and More Information: Visit yes-per.com

Environmental Protection

Do not dispose of this product with regular household waste at the end of its life cycle. Please hand it over to an appropriate collection point for the recycling of electrical and electronic appliances. The symbols on the product, instructions, or packaging will provide information on disposal methods.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.