Dooya DC136+DC115

Contents

Dooya DC136 Receiver and DC115 Emitter Wireless Controller Kit User Manual

For 4-Wire Tubular Motors of Rolling Shutters, Garage Doors, and Awnings

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dooya DC136 Receiver and DC115 Emitter Wireless Controller Kit. This kit is designed to provide convenient remote control for 4-wire tubular motors commonly found in rolling shutter doors, garage doors, and awnings.

Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Information

  • **High Voltage Warning:** This device operates with high voltage (above 50Vac or 75Vdc). Installation should only be performed by qualified personnel to prevent electric shock or damage.
  • Ensure the power supply matches the voltage specified on the product nameplate (typically 220-240V, but some models may support 120V/60Hz).
  • Disconnect power before performing any installation, wiring, or maintenance.
  • Keep the receiver and emitter away from water and excessive humidity.
  • Do not attempt to open or repair the devices yourself. Refer all servicing to qualified personnel.

3. Package Contents

The Dooya DC136+DC115 kit typically includes the following components:

  • 1 x Dooya DC136 RF433 Receiver
  • 2 x Dooya DC115 RF433 Emitters (Remote Controls)
  • Necessary wiring/connectors
Dooya DC136 Receiver and two DC115 Emitters with wiring
Figure 3.1: Kit Contents - DC136 Receiver, two DC115 Emitters, and wiring.

4. Components Overview

4.1 DC136 RF433 Receiver

The DC136 is the central control unit that receives signals from the DC115 emitters and controls the tubular motor. It features indicator lights and control buttons for pairing and other functions.

Close-up of the Dooya DC136 RF433 Receiver
Figure 4.1: Dooya DC136 RF433 Receiver.
DC136 Receiver showing Pair Button and Pause Button locations
Figure 4.2: DC136 Receiver with 'Pair Button' and 'Pause Button' indicated.

4.2 DC115 RF433 Emitter

The DC115 is a handheld remote control used to send commands to the DC136 receiver. It typically features buttons for Up, Down, Stop, and potentially a channel/self-locking function.

Close-up of two Dooya DC115 Emitters (remote controls)
Figure 4.3: Dooya DC115 RF433 Emitters.
DC136 receiver and an opened DC115 emitter showing internal battery
Figure 4.4: DC136 Receiver and DC115 Emitter (opened to show battery compartment).

5. Setup and Installation

5.1 Wiring the DC136 Receiver

The DC136 receiver is designed for 4-wire tubular motors. Ensure all connections are secure and correctly matched to avoid damage or malfunction. Professional installation is highly recommended due to high voltage.

Detailed view of the 7-wire connector for the DC136 receiver
Figure 5.1: DC136 Receiver 7-wire connector detail. Connect motor wires and power line as indicated.

Typical wiring color codes (refer to your motor's specific instructions and local electrical codes):

  • For 230V/50Hz systems:
    • Blue = Neutral
    • Black = Live 1 (e.g., Up)
    • Brown = Live 2 (e.g., Down)
    • Green/Yellow = Earth
  • For 120V/60Hz systems:
    • White = Neutral
    • Red = Live 1 (e.g., Up)
    • Black = Live 2 (e.g., Down)
    • Green = Earth
Comprehensive wiring diagram for a rolling shutter system with DC136+DC115
Figure 5.2: General wiring diagram for a rolling shutter system with DC136 Receiver and DC115 Emitter.
  • Shortest distance between receiver and ground: ≥ 1.5m
  • Shortest distance between receiver and roof: ≥ 0.3m
  • Shortest distance between receivers (if multiple are used): ≥ 0.2m

5.3 Pairing the DC115 Emitter with the DC136 Receiver

To enable remote control, you must pair the DC115 emitter(s) with the DC136 receiver:

  1. Ensure the DC136 receiver is powered on.
  2. Press the **Pair Button** on the DC136 receiver once. The LED indicator on the DC136 will flash, then become steadily bright.
  3. Within 10 seconds, press the **Up button** on the DC115 emitter.
  4. The LED indicator on the DC136 will flash again, then turn off, indicating successful pairing.

Note: If the operations are not completed within 10 seconds, the receiver will revert to its original state, and you will need to restart the pairing process.

Close-up of a DC115 emitter highlighting the UP BUTTON for pairing
Figure 5.3: DC115 Emitter with 'Up Button' highlighted for pairing.

6. Operation

6.1 Basic Control

Once paired, use the DC115 emitter to control your motor:

  • **Up Button:** Moves the shutter/awning upwards.
  • **Down Button:** Moves the shutter/awning downwards.
  • **Stop Button:** Stops the motor's current movement.

6.2 Deleting All Emitter Channels

To remove all paired emitters from the DC136 receiver:

  1. Ensure the DC136 receiver is powered on.
  2. Press the **Pair Button** on the DC136 receiver once.
  3. Within 10 seconds, press and hold the **Stop and Down buttons** on the DC115 emitter simultaneously for 6 seconds.
  4. The LED indicator on the DC136 will flash, then turn off, confirming all emitters have been deleted.

6.3 Reversing Motor Direction

If the Up/Down buttons on the emitter operate the motor in the opposite direction to what is desired, you can reverse the direction:

  1. Ensure the DC136 receiver is powered on.
  2. Press the **Pair Button** on the DC136 receiver once.
  3. Within 10 seconds, press and hold the **Stop button** on the DC115 emitter for 6 seconds.
  4. The LED indicator on the DC136 will flash, then turn off, indicating the motor direction has been successfully reversed.

6.4 Emitter Self-locking Function (if applicable)

Some DC115 emitters may feature a self-locking function to prevent accidental operation:

  • If your DC115 has a dedicated self-locking button (often the fourth button), pressing it may disable the emitter's control over the motor. This is useful to avoid misoperation.
  • To re-enable control, press the Stop button on the emitter.

7. Maintenance

  • **Cleaning:** Wipe the receiver and emitter with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • **Battery Replacement (DC115 Emitter):** If the emitter's range decreases or it stops responding, the battery may need replacement. Refer to Figure 4.4 for an internal view. Ensure correct polarity when inserting a new battery.
  • **Connection Check:** Periodically inspect wiring connections to the DC136 receiver to ensure they are secure and free from corrosion.

8. Troubleshooting

Problem Possible Cause Solution
Emitter not controlling motor. Not paired; Emitter battery low/dead; Receiver not powered; Out of range; Self-locking engaged. Perform pairing procedure (Section 5.3); Replace emitter battery; Check power to DC136; Move closer to receiver; Disengage self-locking (Section 6.4).
Pairing fails. Timing issue during pairing; Incorrect button sequence. Ensure all steps are completed within 10 seconds; Follow pairing steps precisely (Section 5.3).
Motor moves in wrong direction. Motor direction needs reversal. Perform direction reversal procedure (Section 6.3).
Reduced control range. Emitter battery low; Environmental interference (e.g., concrete walls). Replace emitter battery; Consider receiver placement to minimize obstructions.

9. Specifications

Feature Specification
Model Number Dooya DC136+DC115
Receiver (DC136) Max Output Power 500W
Receiver (DC136) Channel Storage Up to 20 valid channels
Voltage 220-240V (Refer to product nameplate for 120V/60Hz compatibility)
RF Frequency 433.92MHz (433.05~434.79MHz)
Control Range (Line of Sight) 200m
Control Range (with Concrete Walls) 35m
Motor Compatibility 4-wire tubular motors
Certification CE
Battery Included (Emitter) No
Origin Mainland China

10. User Tips

  • **Additional Emitters:** If you require multiple control points for your motor (e.g., from different rooms or multiple users), consider purchasing additional DC115 emitters.
  • **Battery Type:** Ensure you use the correct battery type for the DC115 emitter when replacing it.
  • **Signal Obstruction:** For optimal performance, try to minimize physical obstructions (especially thick walls) between the emitter and the receiver.

11. Further Information and Support

For more detailed technical specifications or if you encounter issues not covered in this manual, please refer to the official user manual PDF available from the seller. You can typically find this document at the following link:

View User Manual (PDF)

If you require further assistance, please contact the seller or your local Dooya service center.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.