HXCONTROLLER MPPT Solar Battery Charge Controller (HM Series)

Contents

MPPT Solar Battery Charge Controller User Manual

Brand: HXCONTROLLER

Model: MPPT Solar Battery Charge Controller (HM Series)

1. Introduction

This product can detect the power generation of solar panels in real-time and track the highest voltage and current value (VI), allowing the system to charge the battery at maximum power output. Applied in solar off-grid photovoltaic systems, coordinating the work of solar panels, batteries, and loads is the core control component of off-grid photovoltaic systems.

This product adopts LCD display for operating status, operating parameters, control parameters, etc. Users can easily access various parameters through buttons and modify control parameters as needed to meet different system requirements.

The controller has comprehensive electronic fault self-test function and powerful electronic protection function inside, which can minimize the damage to product components caused by installation errors and system failures.

MPPT Solar Charge Controller with built-in WiFi and app monitoring
Figure 1.1: MPPT Solar Charge Controller with built-in WiFi and app monitoring interface.

2. Safety Instructions

  1. Due to the fact that the voltage applicable to this controller exceeds the safety voltage of the human body, please read the manual carefully before operation and only operate this controller after completing safety operation training.
  2. There are no components inside the controller that require maintenance or repair. Users should not disassemble or repair the controller on their own.
  3. Please install the controller indoors to avoid exposure of components and prevent water from entering the interior of the controller.
  4. Please install the controller in a well ventilated area, as the temperature of the heat sink will be very high during operation.
  5. Suggest installing suitable fuses or circuit breakers outside the controller.
  6. Before installing and adjusting the wiring of the controller, be sure to disconnect the wiring of the photovoltaic array and the fuses or circuit breakers near the battery terminals.
  7. After installation, check if all wiring connections are tight to avoid the danger of heat accumulation caused by virtual connections.

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Product Features

  • The built-in maximum power tracking algorithm can significantly improve the energy utilization efficiency of photovoltaic systems, which is about 25% higher than traditional PWM charging efficiency.
  • MPPT tracking efficiency can reach up to 99.9%.
  • Adopting advanced digital power supply technology, the energy conversion efficiency of the circuit can reach up to 98%.
  • Support different types of battery charging programs such as colloidal batteries, sealed batteries, open end batteries, and lithium batteries.
  • It has a current limiting charging mode. When the power of the battery board is too high and the charging current exceeds the rated current, the controller automatically reduces the charging power to operate at the rated charging current.
  • Built-in over-temperature protection mechanism. When the temperature exceeds the device setting value, the charging current decreases linearly with the temperature, thereby reducing the temperature rise of the controller and avoiding high temperature damage to the controller.
  • With temperature compensation function, it can automatically adjust the charging and discharging parameters to increase the battery life.
  • Adopting a metal shell for better heat dissipation performance.
  • Lithium battery OV charging function.
  • The high input voltage resistance charging of solar panels can reduce the specifications of solar wiring wires and reduce system costs.
  • You can choose models that support RS485 protocol to meet the communication needs of different occasions.
  • The display interface can be switched freely between Chinese and English.
High Tracking Efficiency and Controller Dimensions
Figure 3.1: High Tracking Efficiency (99% Max Tracking, >98% Peak Conversion) and controller dimensions (21.5cm x 25.9cm x 10.3cm).
MPPT Solar Controller Protection Features
Figure 3.2: MPPT Solar Controller features including various protections, auto fan cooling, colorful menu screen, and advanced settings.

4. Setup: Installation and Wiring

4.1. Installation Safety Distance

To ensure effective heat dissipation of the controller, please follow the following safety clearances for installation:

  • Left/Right: 20CM
  • Top/Bottom: 30CM
Installation Hole Diagram of MPPT Solar Charging Controller
Figure 4.1: Installation hole diagram and dimensions for various models (e.g., HM-6048, HM-8048, HM-12048).

4.2. Line Connection Requirements

First connect the positive and negative terminals of the battery, then connect the positive and negative terminals of the DC load, and finally connect the positive and negative terminals of the solar panel.

Wiring Diagram for MPPT Solar Charge Controller
Figure 4.2: Connection diagram showing PV input, Battery, Load, and RS485 connections.

4.3. Installation Precautions

  • When installing batteries, be very careful. For open lead-acid batteries, wear protective goggles. If in contact with battery acid, rinse with clean water in a timely manner.
  • Avoid placing metal objects near the battery to prevent short circuits.
  • During battery charging, acidic gases may be generated; ensure good ventilation around the environment.
  • Batteries may produce combustible gases; please stay away from sparks.
  • Outdoor installation should avoid direct sunlight and rainwater infiltration.
  • Virtual connection points and corroded wires may cause significant heating and melting of the insulation layer of the wires, burning of surrounding materials, and even causing fires. Therefore, it is important to ensure that the connection heads are tightened, and it is best to fix the wires with zip ties to avoid shaking the wires during mobile applications and causing the connection heads to become loose.
  • When connecting the system, the output voltage of the component may exceed the safety voltage of the human body. When operating, be careful to use insulated tools and ensure that your hands are dry.
  • The battery terminals on the controller can be connected to either the same battery or the same set of batteries.
  • Please follow the safety recommendations of the battery manufacturer.
  • The system connection wires are selected according to a current density not exceeding 4A/mm².
  • Ground the ground terminal of the controller.

5. Operation

5.1. Main Interface Overview

The controller features an LCD display and control buttons for easy interaction.

  • Solar charging controller function indicator light: Indicates the operational status.
  • Solar charging controller LCD display screen: Displays various parameters and settings.
  • Solar charging controller interface setting button (ESC, UP, DOWN, SET): Used for navigation and parameter adjustment.
  • Installation hole for solar charging controller: Mounting points for the device.

5.2. Key Operation Instructions

The display provides real-time information about the solar system. Key indicators include:

  • Solar panel indicator light
  • Charging indicator light
  • Load indicator light
  • Warning indicator light
  • Return/load switch key
  • Flip Up/+ button
  • Down Page/- button
  • Confirm/Set key
  • Solar panel input voltage
  • Battery charging current
  • Daytime/Photovoltaic panels
  • WiFi status indicator
  • Real-time clock
  • Battery charging power
  • DC load output power
  • DC load
  • DC load output current
  • DC load output voltage
  • Battery voltage

5.3. Device Information Browsing

Short press the UP and DOWN buttons to browse through different screens displaying device information and current curves (daily, 1 day ago, 2 days ago, 3 days ago).

5.4. Quick Parameter Setting

On the main page, press and hold the SET button for 3 seconds to enter quick settings. Parameters that can be adjusted include:

  • Backlight mode (Keep On, Delayed closing)
  • Load output Type (Light controlled switch, Always closed, Always open)
  • Load opening time
  • Time setting
  • Clean generation
  • Language (English, Chinese)

5.5. Advanced Settings

On the main page, press and hold the ESC key and the SET key for 5 seconds to enter the advanced system settings. Enter the correct password (default: 1111). Use the UP and DOWN keys to browse and adjust advanced parameter settings. Customized battery type parameter settings and charging current settings support long press for quick adjustment.

5.6. WiFi Status Indicator (WiFi version only)

The WiFi icon on the display indicates the connection status:

  • WiFi module abnormality: WiFi icon flashes red slowly.
  • WiFi not connected: WiFi icon flashes white slowly.
  • Excellent WiFi signal: WiFi icon 3 bars blue.
  • Good WiFi signal: WiFi icon 2 bars blue.
  • Poor WiFi signal: WiFi icon 1 bar blue.

For a better experience, place the controller in a location with good WiFi signal. Restoring factory settings can unbind the device. The device time will be automatically calibrated after the WiFi connection is successful.

Video 5.1: Product demonstration showing the controller's display and features.
MPPT Solar Charge Controller with WiFi App Monitoring
Figure 5.2: The MPPT Solar Charge Controller supports WiFi connectivity for remote monitoring via a mobile application.

6. Specifications

6.1. Parameter Table

ParameterHM60192HM120192
Product IDHM60192HM120192
Maximum photovoltaic voltage0-160V0-230V
Charging Current0-60A Adjustable0-120A Adjustable
Battery TypeSealed battery, Gel battery, Watering battery, Lithium iron phosphate battery, Ternary lithium battery
Battery Voltage Recognition12V/24V/48V Automatic recognition + adjustable (12V/24V/48V)12V/24V/48V/96V Automatic recognition + adjustable (12V/24V/48V/60V/72V/84V/96V)
Battery Voltage Range12V/24V/36V/48V12V/24V/36V/48V/60V/72V/84V/96V
Maximum input power of solar panel1440W/24V, 2880W/48V, 5760W/96V, 11520W/192V2880W/24V, 5760W/48V, 11520W/96V, 23040W/192V
Custom Voltage9-240V Adjustable
Charging methodPower tracking, fast charging, floating charging
Start chargingPhotovoltaic voltage > battery voltage + 2V
DC output function40A
Communication interfaceRS485/WiFi/Bluetooth (optional)
Operating temperature-20°C~65°C
Cooling methodAir Cooling
Altitude0-3000m
Product size262x218x102mm329x268x102mm
Color box size282x221x140mm370x285x151mm
Outer box size458x440x308mm620x385x290mm
Net weight2860g4850g
Gross Weight3000g5100g
Outer box weight18.9kg/6 units20.4kg/4 units

7. Troubleshooting

If you encounter issues with your MPPT Solar Battery Charge Controller, consider the following general troubleshooting steps:

  • No Power/Display: Check all wiring connections, especially to the battery, for tightness and correct polarity. Ensure the battery has sufficient charge.
  • No Charging: Verify that solar panels are receiving adequate sunlight and are connected correctly. Check the input voltage from the solar panels on the controller's display. Ensure the battery type settings are correct.
  • Over-current/Over-voltage Warnings: Review your solar panel array configuration to ensure it does not exceed the controller's maximum input voltage or current ratings. Check battery voltage and ensure it's within the controller's operating range.
  • High Temperature: Ensure the controller is installed in a well-ventilated area with sufficient clearance as specified in the installation section. Check if the cooling fan is operating correctly.
  • WiFi Connectivity Issues: Ensure the controller is within range of a strong WiFi signal. Check WiFi settings on the controller and your monitoring app. If issues persist, try restoring factory settings (note: this will unbind the device).
  • Incorrect Readings: Verify that all sensors (e.g., temperature sensor) are properly connected.

For more detailed troubleshooting, refer to the comprehensive user manual PDF available from the seller.

8. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your MPPT Solar Battery Charge Controller:

  • Visual Inspection: Periodically inspect all wiring connections for signs of corrosion, loose terminals, or damage. Ensure all components are securely mounted.
  • Cleanliness: Keep the controller clean and free from dust and debris. Ensure the cooling fan (if present) and ventilation openings are not obstructed. Use a dry, soft cloth for cleaning.
  • Environmental Check: Confirm that the installation environment remains dry, well-ventilated, and within the specified operating temperature range. Protect the unit from direct sunlight and moisture.
  • Firmware Updates: Check the manufacturer's website or app for any available firmware updates that may improve performance or add features.
  • Battery Health: Regularly monitor your battery's health and charge status through the controller's display or app. Ensure your battery type settings are accurate for proper charging.

Do not attempt to open or repair the controller yourself, as it contains no user-serviceable parts and doing so may void your warranty and pose safety risks.

9. User Tips

  • Optimal Panel Configuration: For maximum efficiency, ensure your solar panels are configured in series to utilize the controller's high voltage input capability (up to 230VDC for some models), which can reduce wiring losses.
  • Monitor via App: Take advantage of the built-in WiFi feature and mobile app to remotely monitor your system's performance, battery status, and adjust settings conveniently.
  • Battery Compatibility: Always double-check that the controller's battery type setting matches your actual battery (Lifepo4, GEL, Lead Acid, etc.) to prevent damage and ensure efficient charging.
  • Ventilation is Key: Proper airflow around the controller is crucial for heat dissipation, especially during high-power operation. Adhere to the recommended safety distances during installation.

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official user manual PDF provided by the manufacturer. This document contains comprehensive instructions and specifications.

You can access the official user manual PDF here: Download User Manual (PDF)

11. Compliance

Disclaimer

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.