HOMCOM Sliding Door Installation Kit B81-006

Contents

HOMCOM Sliding Door Installation Kit User Manual

Model: B81-006

1. Introduction

Thank you for choosing the HOMCOM Sliding Door Installation Kit. This kit provides the necessary hardware to install a single wooden sliding door, offering a space-saving and stylish solution for various rooms in your home. Please read this manual carefully before installation and retain it for future reference.

Installed wooden sliding door with the HOMCOM kit
Example of an installed wooden sliding door using the kit.

2. Package Contents

Before beginning installation, please ensure all components listed below are present and undamaged.

All components of the HOMCOM sliding door installation kit laid out
All components included in the installation kit.
  • Aluminum alloy rail sections
  • Sliding rollers (hangers)
  • Wooden mounting board (MDF)
  • Floor guide
  • Door stoppers
  • Anti-jump discs
  • Screws and anchors for cement walls
  • Wrench
  • Other necessary fasteners

3. Specifications

Diagram showing key dimensions and specifications for the sliding door kit
Key dimensions and requirements for installation.
FeatureDetail
MaterialAluminum Alloy (rail), MDF (mounting board)
Rail Length200 cm
Rail Dimensions (LxWxH)200 x 3.05 x 3.06 cm
Maximum Supported Door Weight75 kg
Suitable Door Thickness35-45 mm (wooden doors only)
Maximum Door Width100 cm
Minimum Clearance (Door to Ceiling)13 cm
Required Rail LengthMinimum double the door width
Product Weight4 kg
ReferenceB81-006

Important: This kit is ONLY for wooden doors and SHOULD NOT be used on hollow walls.

4. Setup and Installation

This section outlines the general steps for installing your sliding door kit. Professional installation is recommended if you are unsure about any steps.

4.1 Pre-Installation Checks

  • Ensure your wall is solid (e.g., cement) and can support the weight of the door and the rail system (up to 75 kg). Do not install on hollow walls.
  • Verify your wooden door's thickness is between 35-45 mm and its width is no more than 100 cm.
  • Confirm you have at least 13 cm of clearance above the door opening for mounting the rail.
  • The rail length (200 cm) is designed for doors up to 100 cm wide, as the rail should be at least double the door's width.

4.2 Installation Steps (General Guide)

  1. Prepare the Wall: Mark the desired height for the top of the wooden mounting board. Ensure it is level and provides the minimum 13 cm clearance above the door.
  2. Install Mounting Board: Secure the MDF mounting board to the wall using appropriate fasteners. For cement walls, use the provided durable screws and anchors. Ensure it is firmly attached.
  3. Attach Rail to Mounting Board: Align the aluminum alloy rail with the mounting board and secure it using the provided screws. Ensure the rail is perfectly level.
  4. Install Rollers on Door: Attach the sliding rollers (hangers) to the top edge of your wooden door. Ensure they are evenly spaced and securely fastened.
  5. Hang the Door: Carefully lift the door and hook the rollers onto the rail.
  6. Install Door Stoppers: Position and secure the door stoppers at both ends of the rail to prevent the door from sliding off. Adjust them to control the door's travel distance.
  7. Install Floor Guide: Mount the floor guide to the floor directly below the rail, ensuring it aligns with the groove at the bottom of your door (if applicable) or guides the door's movement.
  8. Attach Anti-Jump Discs: Install the anti-jump discs on the top edge of the door, above the rail, to prevent the door from lifting off the track.
  9. Final Adjustments: Test the door's movement. Adjust stoppers and rollers as needed for smooth operation.
Close-up view of the wooden mounting board and aluminum rail installation
Detail of the wooden mounting board and rail attachment.

5. Operating Instructions

Once installed, your sliding door system is designed for simple operation:

  • To open or close the door, gently push or pull it along the rail.
  • The rollers are designed for smooth and quiet movement.
  • The door stoppers will prevent the door from exceeding its intended travel limits.

6. Maintenance

Regular maintenance will ensure the longevity and smooth operation of your sliding door system:

  • Cleaning: The aluminum alloy rail and other components can be easily cleaned with a damp cloth. Avoid abrasive cleaners.
  • Lubrication: Periodically apply a silicone-based lubricant to the roller wheels and the rail to maintain smooth gliding.
  • Fastener Check: Every few months, check all screws and fasteners to ensure they are tight. Re-tighten if necessary to prevent sagging or instability.
  • Door Condition: Inspect your wooden door for any warping or damage that might affect its movement.

7. Troubleshooting

ProblemPossible CauseSolution
Door is difficult to slideLack of lubrication, debris in rail, loose rollersClean the rail, lubricate rollers, check and tighten roller fasteners.
Door makes noise when slidingDry rollers, misaligned rail, loose componentsLubricate rollers, check rail alignment, tighten all fasteners.
Door sags or feels unstableLoose mounting board or rail fasteners, overloaded doorRe-tighten all mounting screws. Ensure door weight does not exceed 75 kg.
Door comes off the trackAnti-jump discs not installed or improperly adjustedInstall or adjust anti-jump discs to ensure they prevent the door from lifting.

8. User Tips

  • Wall Type: Always ensure the wall where the rail is mounted is solid and capable of supporting the door's weight. Avoid hollow walls for safety and stability.
  • Aesthetics: The MDF mounting board can be painted to match your wall color or door, providing a seamless look. Consider painting it before installation for easier application.
  • Door Selection: Choose a wooden door that is slightly wider than your opening to ensure full coverage when closed.
  • Professional Help: If you are not comfortable with DIY installation, consider hiring a professional to ensure correct and safe setup.
Multiple room settings where the sliding door kit can be used, with a warning about hollow walls
The sliding door kit is suitable for various rooms, but remember: DO NOT USE ON HOLLOW WALLS.

9. Warranty and Support

For any questions regarding installation, operation, or parts, please contact HOMCOM customer support. Keep your purchase receipt for warranty claims.

This product is designed for residential use. Any modifications to the product or use for purposes other than its intended design may void the warranty.

© 2024 HOMCOM. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.