1. Introduction
The Hantek HTM200 series handheld multi-channel temperature detector is a high-performance device designed for real-time temperature data acquisition across multiple channels. Powered by a 32-bit ARM microprocessor, it offers stable and accurate measurements, supporting various thermocouple types and advanced features like alarm control and data storage. This manual provides essential information for the proper setup, operation, and maintenance of your HTM208B or HTM208C temperature data logger.

Figure 1: Hantek HTM208B/HTM208C Multi-Channel Temperature Data Logger and included accessories.
2. Setup
2.1. Package Contents
Before starting, please verify that all items are present in your package:
- Hantek HTM208B or HTM208C Temperature Data Logger
- Thermocouple probes (typically two blue probes)
- Power adapter
- USB Type-C cable
- Carrying case

Figure 2: Contents of the Hantek HTM208B/HTM208C package.
2.2. Battery Installation and Charging
The device uses 18650 standard lithium batteries. Please note that due to air transportation safety restrictions, batteries are not shipped with the product and must be purchased separately. Once batteries are installed, the device supports Type-C charging.
- Open the battery compartment cover on the back of the device.
- Insert two 18650 lithium batteries, ensuring correct polarity.
- Close the battery compartment cover.
- To charge, connect the device to the power adapter using the provided USB Type-C cable.
2.3. Thermocouple Connection
The HTM208B/HTM208C features 8 channels for thermocouple connections.
- Identify the thermocouple connection ports at the bottom of the device, labeled 1 through 8.
- Connect your thermocouple probes to the desired channels. Ensure a secure connection for accurate readings.
- The device supports 11 types of thermocouples: J, K, T, E, S, N, B, R, A, C, D.

Figure 3: Device overview showing Thermocouple Connection Ports, TFT Display, Push Buttons, USB, and Type-C interfaces.
3. Operation
3.1. Power On/Off
Press and hold the 'POWER' button located on the side of the device to turn it on or off.
3.2. Display and Navigation
The device features a 320*240 TFT high-definition display. You can intuitively view multi-channel real-time temperature changes. Use the navigation buttons (up, down, left, right, Enter) and function keys (F1-F4, Utility, List, Bar, Save) to navigate menus and control settings.
- List Display: Shows temperature readings for all active channels in a list format.
- Bar Graph Display: Visualizes temperature data using bar graphs for easy comparison.
- Save: Use this button to save current data.
- Utility: Access various utility functions and settings.

Figure 4: Front view of the Hantek HTM208B/HTM208C, highlighting the display and control buttons.
3.3. Temperature Measurement
The device supports 11 types of thermocouples (J/K/T/E/S/N/B/R/A/C/D). Ensure the correct thermocouple type is selected in the device settings for accurate measurements. Each channel can be individually corrected for precision.

Figure 5: The device supports 11 types of thermocouples for versatile temperature measurement.
3.4. Data Logging and Storage
The HTM208B/HTM208C comes standard with U disk storage. An optional Micro SD card can also be used for additional data storage, export, and printing.
3.5. Alarm Control
The device features an over-temperature alarm function. When the measured temperature exceeds a set upper limit or falls below a set lower limit, the buzzer will sound continuously to alert the user. This function is enabled by default.

Figure 6: Device highlighting Type-C charging and upper/lower overrun alarm capabilities.
3.6. Software and Connectivity
The device supports Windows and Android data acquisition software, enabling multi-platform data acquisition and monitoring. It features a standard Type-C communication function, with optional Bluetooth and 4G communication modules available for remote data collection.

Figure 7: The device can connect to various platforms (Windows, Android) for data acquisition and monitoring.
Video 1: An overview of the Hantek HTM208B/HTM208C Multi-Channel Temperature Data Logger in operation.
4. Maintenance
4.1. Cleaning
To maintain the device's performance and appearance, regularly wipe the exterior with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the casing or screen.
4.2. Battery Care
When not in use for extended periods, remove the 18650 lithium batteries to prevent leakage and damage. Store batteries in a cool, dry place. Recharge batteries regularly to prolong their lifespan.
4.3. Storage Environment
Store the device in an environment with temperatures between -10°C and 60°C and relative humidity below 90% RH. Avoid extreme temperatures, direct sunlight, and high humidity to prevent damage to internal components.
5. Troubleshooting
- Device not powering on: Check if the 18650 batteries are correctly installed and charged. Ensure the power button is pressed firmly.
- Inaccurate temperature readings: Verify that the thermocouple probes are securely connected and that the correct thermocouple type is selected in the device settings. Perform a cold junction compensation check if available.
- Data transfer issues: Ensure the USB Type-C cable is properly connected to both the device and the computer. If using optional Bluetooth/4G, check connection status and software settings.
- Alarm not functioning: Check the alarm settings (upper and lower limits) in the device menu. Ensure the buzzer is not muted.
- Sensor Fault Detection: The device has a function to detect faulty or disconnected sensors. If a channel shows an abnormal reading or error, check the physical connection of the thermocouple to that channel.
6. Specifications

Figure 8: Detailed specifications for HTM208B and HTM208C models.
| Feature | HTM208B | HTM208C |
|---|---|---|
| U disk | Yes | Yes |
| Bluetooth | Without | Yes |
| SD card | Without | Without |
| 4G (domestic) | Without | Without |
| 4G (Universal Version) | Without | Without |
| Graduation number | 11 kinds of thermocouples: J/K/T/E/S/N/B/R/A/C/D type | |
| Type K thermocouple: Basic accuracy | -200°C to 0°C error is ±1.2°C The error from 0°C to 1370°C is ±0.8°C (excluding thermocouple error) | |
| Temperature measurement range | Type K thermocouple: -200°C to 1370°C | |
| Resolution | 0.1°C | |
| Correction | Each channel can be corrected | |
| Alarm | Support upper and lower limit alarms | |
| Display | Support list display and bar graph display | |
| Cold Junction Compensation | Accuracy: 0.5°C | |
| Software support | Android and Windows data acquisition software | |
| Storage | Support U disk (standard) and Micro SD card (optional) to save in real time | |
| Communication Interface | USB-Type C communication (standard), Bluetooth and 4G communication (optional) | |
| Maximum withstand voltage between channels | 300VDC | |
| Channel maximum input voltage | ±75VDC | |
| Plug in terminal type | E0308 Tube Terminal Blocks | |
| Other | 2.8 inch TFT-LCD display, USB communication, compatible with SCPI instruction set, Support Chinese and English, Backlight brightness adjustment, Shutdown time settings | |
| General characteristics | ||
| Operating environment | 0-40°C, <80%RH | |
| Storage environment | -10-60°C, <90%RH | |
| Preheat time | >30 minutes | |
| Power Requirements | Input: 100VAC ~ 240VAC, 50Hz/60Hz Output: 5V/2A DC | |
| Battery parameters | Two 3.7V 18650 lithium batteries (Excluding batteries) | |
| Working hours | >15 hours | |
| Working power consumption | 1W | |
| Size and weight | Size: 200mm*98mm*40mm Weight: 600g | |

Figure 9: Physical dimensions of the Hantek HTM208B/HTM208C.
7. User Tips
No specific user tips were found in the provided reviews or Q&A content. For optimal performance, always ensure thermocouples are correctly calibrated and securely connected.
8. Warranty and Support
For any technical assistance, warranty claims, or support inquiries, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact information.
9. Applications
The Hantek HTM208B/HTM208C is widely used in various industrial and research applications, including:
- Product R&D
- Incoming inspection of components
- On-line inspection of products
- Electronic engineering development
- Teaching experiments
- Technology and R&D
- Electronic equipment maintenance
- Cold storage and warehouse temperature monitoring
- Surface measurement of electronic components

Figure 10: Examples of industrial and research applications for the temperature data logger.