1. Introduction
The Ezonetronics RM-DAB003 is a versatile DAB/DAB+ active antenna with a USB adapter designed to enhance your in-car audio experience. It allows you to receive DAB/DAB+ digital radio signals, listen to DAB radio, and output audio via AUX. This plug-and-play device is compatible with various car audio systems, providing clear digital sound quality.


2. Product Features
- DAB/DAB+ Signal Reception: Receives digital audio broadcasting signals for a wide range of radio stations.
- FM Transmitter Function: Converts the DAB/DAB+ radio signal into a standard FM signal, allowing older car stereos to receive digital radio without direct AUX input.
- AUX Connection: Provides an AUX output for direct connection to your car stereo's AUX port, ensuring high-quality audio transmission.
- Plug and Play Installation: Simple setup with USB external power supply. No complex app installations required.
- Universal Compatibility: Designed for universal car use.
- Compact Design: Small size for discreet installation, replacing traditional bulky car antennas.
- Enhanced Sound Quality: Features a built-in RF amplifier and a high-conductivity, low-resistance FPC printed antenna for strong signal reception and clear sound.

3. Specifications
| Feature | Detail |
|---|---|
| Model | RM-DAB003 |
| Antenna Cable Length | 3 meters |
| Antenna Connector | SMB Right Angle (MCX plug for connection to DAB+ unit) |
| Working Frequency (Band III) | 170MHz~240MHz |
| Working Frequency (L-Band) | 1452MHz~1492MHz |
| DAB+ Unit Dimensions (L x W x H) | 60mm x 30mm x 13mm |
| Antenna Module Dimensions (L x W x H) | Approx. 65mm x 45mm x 25mm |
| Power Input | USB (5V / 2A or above recommended) |

3.1. Compatible DAB Radios
This DAB aerial is suitable for a wide range of in-car DAB radios, including but not limited to:
- Alpine: All in-car DAB except Ezi-DAB
- Beat: All in-car DAB except 400 & 485
- Blaupunkt: All in-car DAB
- Caliber: All in-car DAB except PMT-700D
- C-KO: All in-car DAB
- Clarion: All in-car DAB except DAB302E
- Clarity: CCE203-DAB
- Grundig: All in-car DAB
- JVC: All in-car DAB
- Kenwood: All in-car DAB
- Kinetic: All in-Car DAB
- Philips: CEM series
- Pure Highway: H240Di, H260D
- Sonichi: SB50-DAB
- Sony: All in-car DAB
4. Setup and Installation
4.1. Component Identification

- Antenna Jack: Connects to the DAB+ antenna.
- Micro USB Port: For power supply (connect to a car charger or USB power source).
- Previous Channel/Frequency - Button: Navigates to the previous channel or decreases frequency.
- DAB + Full Scan Button: Initiates a full scan for available DAB/DAB+ stations.
- Next Channel/Frequency + Button: Navigates to the next channel or increases frequency.
- 3.5mm Audio Output: For connecting to the car audio system's AUX input or FM transmitter.
4.2. Wiring Instructions
- Connect the Micro USB port on the DAB+ unit to a car charger or suitable USB power source.
- Connect the MCX plug of the DAB+ antenna to the Antenna Jack on the DAB+ unit.
- Connect the 3.5mm audio output from the DAB+ unit to your car audio system's AUX input. Alternatively, if using the FM transmitter function, ensure the DAB+ unit is powered and broadcasting on an unused FM frequency.

4.3. Antenna Installation Guide
The antenna is designed for discreet installation on your car's front window and A-pillar. Ensure the installation area is clean and dry before proceeding.
- Gently pull down the inner cover of the A-pillar to expose the metal surface.
- Carefully remove the protective film from the antenna.
- Place the black film portion of the antenna onto the metal surface of the A-pillar. Simultaneously, place the transparent film portion onto the front window of the car. Ensure the antenna's ground contact makes firm contact with the car body. Note: Do not cover the position of the A-pillar with the transparent film.
- Securely fix both the black and transparent films, and route the antenna cable neatly.
- Replace the cover of the A-pillar, being careful not to damage or break the black film of the antenna.


Caution: This antenna is unsuitable for use on reflective coated or heated screens. Once permanently installed, the antenna can only be returned for refund if proven faulty. It is recommended to test the aerial by temporarily fixing it in place with sticky tape to ensure satisfaction before permanent installation.
5. Operating Instructions
5.1. Powering On and Initial Scan
- Ensure the DAB+ unit is correctly wired and powered via the Micro USB port. The unit will power on automatically when connected to a powered USB source.
- Press the central "DAB + Full Scan" button to initiate a scan for available DAB/DAB+ radio stations. The display will show the scanning progress.
- Once the scan is complete, the unit will tune to the first available station.
5.2. Changing Stations and Adjusting Frequency
- Use the "Previous Channel/Frequency -" button to navigate to the previous station or decrease the frequency.
- Use the "Next Channel/Frequency +" button to navigate to the next station or increase the frequency.
5.3. Audio Output Modes
The RM-DAB003 offers two primary methods for audio output to your car stereo:
- AUX Connection: Connect the 3.5mm audio output from the DAB+ unit directly to your car stereo's AUX input. Select the AUX input on your car stereo to listen to DAB/DAB+ radio.
- FM Transmitter: If your car stereo does not have an AUX input, the DAB+ unit can transmit the DAB/DAB+ audio over an FM frequency.
- On the DAB+ unit, select an unused FM frequency (e.g., 87.5 MHz) using the channel/frequency buttons.
- Tune your car stereo to the exact same FM frequency.
- The DAB/DAB+ audio will now play through your car stereo via FM.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to the DAB+ unit. | Loose USB connection, faulty USB power source. | Check USB cable connection. Ensure car charger/USB port is functional and provides sufficient power (5V/2A). |
| No DAB/DAB+ signal or poor reception. | Antenna not properly installed, weak signal area, antenna film not making good contact. | Perform a full scan. Ensure antenna is correctly installed on the A-pillar and front window, with good ground contact. Try repositioning the antenna if possible. Check if you are in a DAB/DAB+ coverage area. |
| No audio output from car stereo. | Incorrect audio output mode selected, loose AUX cable, incorrect FM frequency. | If using AUX, ensure the AUX cable is securely connected and your car stereo is set to AUX input. If using FM transmitter, ensure the DAB+ unit and car stereo are tuned to the exact same unused FM frequency. |
| Sound quality is poor (static, interference). | Weak signal, interference from other electronic devices, incorrect FM frequency. | Ensure antenna is properly installed for optimal signal. If using FM transmitter, try a different, clearer FM frequency. Minimize other electronic devices that might cause interference. |
7. User Tips
- For best reception, ensure the antenna is installed in a location with minimal obstructions and good contact with the car's metal frame for grounding.
- When using the FM transmitter, choose an FM frequency that is completely clear of any existing radio stations to avoid interference.
- Regularly perform a "Full Scan" to discover new DAB/DAB+ stations as you travel to different regions.
- Keep the DAB+ unit and antenna clean and free from dust or debris to maintain optimal performance.
8. Warranty and Support
For any product inquiries, technical support, or warranty claims, please contact EzoneTronics customer service. Keep your purchase receipt as proof of purchase.
Note: The antenna, once permanently installed, can only be returned for refund if it proves faulty. It is recommended to test the aerial by temporarily fixing it in place with sticky tape to ensure satisfaction before permanent installation.
For further assistance, please refer to the official EzoneTronics support channels or the retailer from whom you purchased the product.