1. Product Overview
The LILYTECH ZL-7850A Ver 2.0 is a versatile and high-accuracy controller designed for managing both temperature and humidity. It is ideal for applications such as incubators, cheese or sausage drying environments, and wet saunas. This device features multiple outputs for heating, cooling, humidifying, de-humidifying, and specialized functions like egg turning.
2. Setup and Installation
Proper installation is crucial for the accurate and safe operation of your ZL-7850A controller. Please follow these guidelines carefully.
2.1 Mounting the Controller
- The controller requires an installation drilling size of W71 x H29 mm.
- Ensure the mounting location is stable and free from excessive vibration or direct moisture.
- The front side of the controller has an IP65 protection level, meaning it is dust-tight and protected against low-pressure water jets. However, the rear connections are not waterproof.
2.2 Wiring Connections
All wiring should be performed by a qualified individual to prevent electrical hazards. Ensure the power supply is disconnected before making any connections.
- Power Supply: Connect the controller to a 100 ~ 240Vac, 50/60Hz power source using the L (Live) and N (Neutral) terminals (labeled 7 and 8 in Figure 3).
- Sensor Connection: The provided sensor cable is 2 meters long and connects to the dedicated 'Sensor' port (4-pin connector in Figure 3). The sensor measures both temperature and humidity.
- Output Connections:
- R1 (Fan Output): Connect your fan or alarm indicator to terminals 1 and COM (Common). Rated for ≤ 3A.
- R2 (Humidity Output): Connect your humidifying or de-humidifying device to terminals 2 and COM. Rated for ≤ 5A.
- R3 (Temperature Output): Connect your heating or cooling device to terminals 3 and COM. Rated for ≤ 5A.
- R4/R5 (Egg Turn Output): These are timer-controlled outputs, typically used for egg turning mechanisms. Connect your egg turning motor to terminals 4 and COM (for R4) and 5 and COM (for R5). Rated for ≤ 1A each.
2.3 Sensor Placement
- Place the sensor in the environment where temperature and humidity need to be controlled.
- Ensure the sensor is not directly exposed to heat sources, cold drafts, or direct water spray, which could lead to inaccurate readings.
- The sensor cable can be extended up to 50 meters if needed, using appropriate wiring.
3. Operating Instructions
The ZL-7850A controller features a clear display and intuitive buttons for setting parameters.
3.1 Control Buttons
- S (Set): Enters parameter setting mode.
- P (Program): Used to navigate through program parameters.
- ▼ (Down Arrow): Decreases values or navigates options.
- ▲ (Up Arrow): Increases values or navigates options.
3.2 Basic Operation Modes
- Temperature Control: The controller supports both heating and cooling modes. You can set a target temperature and a hysteresis (difference) to maintain the desired range.
- Humidity Control: The controller supports both humidifying and de-humidifying modes. Set your target humidity and hysteresis for precise control.
3.3 Setting Parameters
Refer to the detailed programming guide (not provided here, typically in a full manual) for specific parameter codes and their functions. Generally, press 'S' to enter setting mode, use 'P' to cycle through parameters, and the arrow keys to adjust values. Press 'S' again to save and exit.
3.4 Advanced Functions
- Output Delay Protection: Configurable delays for temperature and humidity outputs to protect connected devices from rapid cycling.
- Alarms: High/low temperature and humidity alarms can be set to alert users to conditions outside the desired range.
- Timer Outputs (R4/R5): These outputs can be configured for periodic activation, commonly used for automatic egg turning in incubators. They can also be manually energized via keys for specific adjustments.
- Calibration: Both temperature and humidity readings can be calibrated to match external reference instruments for enhanced accuracy.
4. Maintenance
To ensure the longevity and optimal performance of your ZL-7850A controller, follow these maintenance tips:
- Cleaning: Regularly wipe the controller's display and casing with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Sensor Care: Keep the sensor clean and free from dust or debris. Do not immerse the sensor in liquids.
- Environmental Conditions: Operate the controller within the specified working environment: -10 ~ 45 Celsius, no more than 85%RH, without dew.
- Connection Checks: Periodically inspect all wiring connections to ensure they are secure and free from corrosion.
5. Troubleshooting
If you encounter issues with your ZL-7850A controller, refer to the following common problems and solutions:
5.1 Common Issues
- No Display/Power:
- Check the power supply connection (L and N terminals).
- Ensure the power source is active and within the 100-240Vac range.
- Inaccurate Readings:
- Verify the sensor is correctly connected to the controller.
- Ensure the sensor is placed in a representative area, away from direct heat/cold or moisture.
- Consider performing a calibration if readings consistently deviate from a known reference.
- Outputs Not Activating:
- Check the wiring of the connected device to the respective output (R1, R2, R3, R4, R5).
- Verify that the set temperature/humidity parameters are configured correctly and the current readings are outside the desired range to trigger the output.
- Check for any active delay protection settings that might be preventing immediate activation.
- Alarms Triggering Incorrectly:
- Review the high/low alarm set points.
- Check sensor accuracy as described above.
5.2 Sensor Failure Alarm
The controller is equipped with a sensor failure alarm. If this alarm activates, it indicates a problem with the connected temperature/humidity sensor. Check the sensor cable for damage and ensure it is securely plugged into the controller. If the issue persists, the sensor may need replacement.
6. Specifications
| Feature | Specification |
|---|---|
| Power Supply | 100 ~ 240Vac, 50/60Hz |
| Sensor Type | Combined Temperature & Humidity Sensor (ZL-SHr05J or ZL-SHr05P) |
| Sensor Cable Length | 2 meters (extendable up to 50 meters) |
| Temperature Accuracy | ±1% / 25 Celsius |
| Humidity Accuracy | ±3% (ZL-SHr05J), ±2% (ZL-SHr05P) |
| Temperature Setting Range | 0.0 ~ 65.0 Celsius |
| Humidity Setting Range | 0 ~ 80%RH (ZL-SHr05J), 0 ~ 99%RH (ZL-SHr05P) |
| Temperature Display Range | -20.0 ~ 80.0 Celsius |
| Humidity Display Range | 0 ~ 99%RH |
| Output R1 (Fan/Multi-function) | ≤ 3A |
| Output R2 (Humidity Control) | ≤ 5A |
| Output R3 (Temperature Control) | ≤ 5A |
| Output R4/R5 (Timer/Egg Turn) | ≤ 1A each |
| Working Environment | -10 ~ 45 Celsius, ≤ 85%RH (no dew) |
| Installation Drilling | W71 x H29 mm |
| Protection Level | IP65 (Front side only) |
| Dimensions | 7.8 x 3.5 x 7.1 cm |
7. User Tips
- Stable Environment: For best results, ensure the controlled environment is as stable as possible, minimizing external fluctuations that could challenge the controller's ability to maintain precise conditions.
- Sensor Calibration: Periodically check the accuracy of your sensor against a trusted reference thermometer and hygrometer. If discrepancies are found, use the calibration function to adjust the controller's readings.
- Output Capacity: Always ensure that the devices connected to the controller's outputs (heaters, humidifiers, fans, motors) do not exceed the specified current ratings for R1, R2, R3, R4, and R5 to prevent damage to the controller.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the original seller or manufacturer. Keep your purchase receipt as proof of purchase.