CENTURY AOKE AEDG-380V RX03+GK06TX-V1.0

Contents

433MHz 2-Channel Wireless RF Remote Control Switch Instruction Manual

Model: AEDG-380V RX03+GK06TX-V1.0 | Brand: CENTURY AOKE

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your CENTURY AOKE 433MHz 2-Channel Wireless RF Remote Control Switch. This system is designed for controlling various electrical appliances and systems, offering flexibility and ease of use in applications such as garage door control, lighting, electric doors, remote control curtains, lifting equipment, motor control, water pumps, projection screen elevators, and security systems.

Wireless RF Remote Control Switch Kit (Receiver, 2 Transmitters, 2 Antennas)
Figure 1: Complete Wireless RF Remote Control Switch Kit

2. Safety Information

  • For your safety and to avoid electric shock accidents, always disconnect the power supply before performing any wiring work.
  • Ensure all connections are secure and insulated to prevent short circuits.
  • The remote control features an anti-accidental touch function. For greater safety and power saving, when the remote control is not used for a long period, it will enter a safe sleep mode.
  • Before initial use or after a period of inactivity, activate the remote control by pressing the 'A' and 'B' keys simultaneously for 0.5 seconds.

3. Specifications

Receiver (Model: AK-380V RX03)

FeatureSpecification
Working VoltageDC12-48V
Standby Power Consumption≦15mA
Signal Sensitivity-105dBm
Modulation ModeASK
Maximum Power3000W
Working Frequency433MHz
Dimensions92 x 65 x 32 mm
Weight130g
Channel2
CertificationCE, FCC, RoHS, UL

Transmitter (Remote Control, Model: AK-GK06TX-V1.0)

FeatureSpecification
Operating VoltageDC8-10V
Transmit Current55mA
Transmit Power22dBm
Transmitting Distance (Ideal)200-2000M (without block and signal interference)
Operating Frequency433MHz
Coding FormatLearning Code
Number of Buttons2 (A, B)
Dimensions150 x 48.6 x 30 mm
Weight116.26g
MaterialNylon Fiber (ABS Shell)
Water ResistanceYes, with Nano-Meter Material Ring
Remote Control Transmitter Dimensions
Figure 2: Remote Control Transmitter Dimensions
Remote Control Transmitter Features (Antenna, Indicator, Buttons, Panel Material)
Figure 3: Remote Control Transmitter Features

4. Package Contents

The standard package includes:

  • 1 x Receiver (AK-380V RX03)
  • 1 x Remote Control Transmitter (AK-GK06TX-V1.0) with batteries
  • 1 x Glue Stick Antenna
  • 1 x Suction Cup Antenna
Glue Stick Antenna
Figure 4: Glue Stick Antenna

5. Setup

5.1. Remote Control Activation

Before using the remote control, ensure it is activated. Open the ON button on the side of the remote control. Then, press the 'A' and 'B' keys simultaneously with both hands for 0.5 seconds to turn on the Remote Control.

Anti-Accidental Touch Function: Activating the Remote Control
Figure 5: Activating the Remote Control

5.2. Pairing Method (Learning Code)

To pair the remote control with the receiver:

  1. Ensure the receiver is powered on. A buzzer sound may indicate it's ready.
  2. Press and hold the learning key on the receiver for 2 seconds. The indicator light on the receiver will turn on.
  3. Release the learning key.
  4. Press and hold any button on the remote control.
  5. The indicator light on the receiver will flash 3 times and then remain steadily on, indicating successful pairing.
Operation Method: Pairing and Working Mode Configuration (Momentary, Latched, Toggle)
Figure 6: Receiver Learning Button and Mode Switches

5.3. Wiring Diagrams

IMPORTANT: Disconnect all power before attempting any wiring. Incorrect wiring can cause damage to the device or electrical shock.

Receiver Unit Overview with Wiring Terminals and Learning Key
Figure 7: Receiver Wiring Terminals Overview

5.3.1. Motor Forward and Reverse Wiring (DC 12-48V Input)

This configuration is suitable for controlling motors that require forward and reverse operation.

Wiring Diagram for Motor Forward and Reverse Control (DC 12-48V Input)
Figure 8: Motor Forward and Reverse Wiring Diagram

5.3.2. Control DC Load Wiring (DC 12-48V Input)

Use this diagram for controlling DC loads such as LED lights or other DC-powered devices.

Wiring Diagram for DC Load Control (DC 12-48V Input)
Figure 9: DC Load Control Wiring Diagram

5.3.3. Control AC Load Wiring (AC 85-380V Input)

This diagram is for controlling AC loads, such as household lighting or other AC appliances.

Wiring Diagram for AC Load Control (AC 85-380V Input)
Figure 10: AC Load Control Wiring Diagram

6. Operating Modes

The receiver supports three working modes: Momentary, Latched, and Toggle. These modes are configured using the dial code switches on the receiver board (refer to Figure 6).

6.1. Mode Switching

  • Momentary Mode: Push both switch No. 1 and No. 2 downwards. In this mode, the relay is active only while the remote button is pressed.
  • Latched Mode: Push switch No. 1 upwards to the 'ON' position, and push switch No. 2 downwards. In this mode, pressing button 'A' turns on the corresponding relay, and pressing button 'B' turns it off.
  • Toggle Mode: Push switch No. 2 upwards to the 'ON' position, and push switch No. 1 downwards. In this mode, each press of the remote button toggles the relay state (on/off).

6.2. Clearing Paired Remotes (Clear Code)

To clear all paired remote controls from the receiver's memory:

  1. Press and hold the learning key on the receiver for more than 8 seconds.
  2. The indicator light will go off after flashing 3 times from a continuously on state.
  3. This indicates that all previously paired remote controls have been successfully cleared. You will need to re-pair any remotes you wish to use.

7. Maintenance

7.1. Remote Control Battery Replacement

The remote control transmitter is powered by a 9V battery. When the indicator light on the remote control becomes dim or the range decreases, it's time to replace the battery. To replace:

  1. Locate the battery compartment on the back of the remote control.
  2. Unscrew the double screws fixing the cover.
  3. Carefully remove the old 9V battery.
  4. Insert a new 9V battery, ensuring correct polarity.
  5. Replace the cover and secure it with the screws.
Remote Control Transmitter Back View with Battery Compartment and Water-Resistant Seal
Figure 11: Remote Control Battery Compartment

7.2. Cleaning and Water Resistance

The remote control features an ABS shell and a Nano-Meter Material Ring for water and dust resistance. To clean, wipe with a dry or slightly damp cloth. Do not immerse the remote control in water or use harsh chemicals.

8. Troubleshooting

8.1. Remote Control Not Responding

  • Check Activation: Ensure the remote control is activated by pressing 'A' and 'B' simultaneously for 0.5 seconds.
  • Battery Check: Replace the 9V battery in the remote control if it is low or depleted.
  • Re-pair: If the remote was previously working and stopped, try re-pairing it with the receiver (see Section 5.2).

8.2. Reduced Signal Range or Intermittent Operation

  • Obstructions: Large obstacles like reinforced concrete walls can significantly reduce the effective range. Try to minimize physical barriers between the remote and receiver.
  • Interference: Other wireless devices operating on similar frequencies (433MHz) can cause interference. Try to relocate the receiver or other devices.
  • Antenna Position: Ensure both the receiver's antenna and the remote control's antenna are unobstructed and positioned for optimal signal reception.

8.3. Load Not Switching

  • Wiring Check: Verify all wiring connections to the receiver and the load are correct and secure according to the diagrams in Section 5.3.
  • Power Supply: Ensure the receiver is receiving the correct operating voltage (DC12-48V or AC85-380V depending on model).
  • Load Compatibility: Confirm the connected load does not exceed the maximum power rating of 3000W.

9. User Tips

  • Optimize Signal Range: While the ideal range is up to 2000M in open terrain, obstacles like reinforced concrete walls can significantly reduce this. For optimal performance, ensure a clear line of sight between the remote and receiver, or test the range in your specific environment before final installation.
  • Multiple Remotes: The receiver can learn multiple remote controls, allowing for flexible control from different locations.
  • Application Versatility: This system is highly versatile. Consider its use for automating various tasks around your home or industrial setting, from simple lighting control to more complex motor operations.
Product Application Examples
Figure 12: Product Application Examples

10. Warranty and Support

This product comes with a 2-year warranty from the date of purchase. For any questions regarding the remote control, its operation, or troubleshooting, please contact our customer service. We are committed to providing timely assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.