1. Introduction
The JIKONG V19 Smart Battery Management System (BMS) is an advanced solution designed for large-capacity series lithium battery packs. It integrates essential functions such as voltage acquisition, high-current active balancing, and comprehensive protection mechanisms including overcharge, over-discharge, overcurrent, and over-temperature protection. The BMS also features a coulomb meter, Bluetooth communication, and optional GPS and RS485/CAN interfaces.
This protection board utilizes energy transfer active balancing technology, capable of achieving a continuous 1A/2A balance current. This high-efficiency balancing ensures battery consistency, extends battery life, and delays aging. It is suitable for various battery types including LiFePo4, Li-ion, and LTO, making it versatile for applications in small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage, base station backup power supplies, and solar power stations.
For detailed instructions and specifications, you can also refer to the official user manual PDF: JIKONG V19 Smart BMS User Manual (PDF).
Video: JIKONG Active Balance BMS Overview, demonstrating balanced cell voltage difference to improve battery performance, 24-hour detection, real-time automatic balancing, 0A~2A balanced current, smart management via app, compatibility with different string numbers, and 6 major protection features.
2. Safety Information
Always prioritize safety when working with battery management systems and high-power battery packs. Improper installation or handling can lead to serious injury or damage to equipment.
- Ensure all wiring connections are correct and secure before powering on the BMS.
- Verify that the balance cable is properly connected and that the P- and B- terminals are correctly wired.
- The BMS should be securely fixed to the battery pack.
- Avoid short circuits during installation and operation.
- Do not exceed the specified current and voltage ratings.
- In case of extreme temperatures, consider using the heating function to protect battery cells.
- If an emergency switch is activated, the BMS will operate for 30 minutes to allow for safe handling, but continuous monitoring is advised.
3. Package Contents
The following items are typically included in your JIKONG V19 Smart BMS package:

Image: JIKONG V19 Smart BMS package contents, showing the BMS unit, an operation manual, a pack box, 4 screws, a 40cm NTC temperature sensor, a 50cm switch, a 25cm CAN cable, and two sets of 70cm wires.
- JIKONG V19 Smart BMS Unit
- Operation Manual
- Pack Box
- Screws (x4)
- NTC Temperature Sensor (40cm)
- Switch (50cm)
- CAN Cable (25cm)
- Wires (70cm x2)
4. Product Overview and Features
The JIKONG V19 Smart BMS offers a comprehensive suite of features for optimal battery management:
- Active Equalization: High-current active balancing (1A/2A) to maintain cell consistency.
- Voltage Acquisition: High-precision voltage acquisition (±3mV).
- Current Acquisition: High-precision current acquisition.
- Protection Functions: Overcharge, over-discharge, overcurrent, over-temperature, under-temperature, and short circuit protection.
- Communication Interfaces: Bluetooth (for APP control), RS485 (optional), CAN (optional), GPS (optional).
- Heating Function: Optional heating to protect batteries in low-temperature environments.
- Parallel Function: Supports battery pack parallel connection (optional).
- ACC Detection: Optional ACC detection for discharge enablement.
- Emergency Switch: Provides 30 minutes of operation during critical events.
- Intelligent Sleep: Reduces self-consumption when the BMS is in standby.
- Information Display: Supports external display screens for real-time battery data.
- Certifications: CE, FCC, RoHS certified.

Image: Six Security Protection features of JIKONG Smart BMS, including Overcharge Protection, Short Circuit Protection, Over Discharge Protection, Over Current Protection, ALL-IN Protection (preventing cable drop or poor contact), and Over Temp Protection.
5. Specifications
5.1. Basic Parameters
| Parameter | Value | Unit |
|---|---|---|
| Supply Voltage | 7.5-36 | V |
| Operating Power Consumption | <900 | mW |
| Operating Temperature | -30-70 | °C |
| Max. Number of Collection Strings | 8 | String |
| Max. Balancing Current (1A/2A options) | 1 or 2 | A |
| Max. Charging Current | 200 | A |
| Max. Discharge Current | 200 | A |
| Max. Instantaneous Current | 400 | A |
| Max. Internal Loop Resistance | 0.35 | mΩ |
| Protective Plate Size | 152.25×127.26×15.6 | mm |
| Finished Weight | 424 | g |
5.2. Default Parameters (Example for LiFePo4)
| Parameter | LiFePo4 Default | Unit |
|---|---|---|
| Balancing Initial Voltage | 3 | V |
| Max. Balancing Current | 2 | A |
| Unit Overcharge Voltage | 3.6 | V |
| Single Overcharge Protection Recovery | 3.55 | V |
| Monomer Undervoltage Protection | 2.6 | V |
| Single Undervoltage Protection Recovery | 2.65 | V |
| Automatic Shutdown Voltage | 2.5 | V |
| SOC-0% Voltage | 2.6 | V |
| SOC-100% Voltage | 3.5 | V |
| Trigger Balancing Differential Pressure | 0.01 | V |
| Charging Overcurrent Protection Delay | 30 | S |
| Charging Overcurrent Protection Release Time | 60 | S |
| Discharge Overcurrent Protection Delay | 300 | S |
| Discharge Overcurrent Protection Release Time | 60 | S |
| Short-circuit Protection Delay | 5 | uS |
| Charging Overtemperature Protection Temperature | 70 | °C |
| Charging Overtemperature Restore Temperature | 60 | °C |
| Discharge Overtemperature Protection Temperature | 70 | °C |
| Discharge Overtemperature Recovery Temperature | 60 | °C |
| Charging Low Temperature Protection Temperature | -20 | °C |
| Charging Low Temperature Restore Temperature | -10 | °C |
| MOS Overtemperature Protection Temperature | 100 | °C |
| MOS Overtemperature Protection Recovery Temperature | 80 | °C |
| Device Address | 0 | / |
6. Setup and Installation
6.1. Physical Installation
The JIKONG V19 Smart BMS is designed for easy integration. Its dimensions are 152.25mm × 127.26mm × 15.6mm. Ensure adequate space and proper ventilation for the unit.

Image: JIKONG V19 Smart BMS physical dimensions and layout, showing the top and side views with measurements.
6.2. Wiring Diagram
Proper wiring is crucial for the safe and correct operation of the BMS. The JIKONG V19 BMS is suitable for 3-8 series lithium battery packs. The specific wiring method depends on the number of cells in your battery pack.

Image: Wiring Diagram for JIKONG V19 Smart BMS. It illustrates connections for the battery pack (B-, B1, B2, B3, B4, B8, B+), load, and charger. It also shows the protection board heating wire, heater element, temperature control switch, and temperature probe.

Image: Detailed wiring diagram for JIKONG Smart BMS. The top diagram shows an 8S configuration with connections for B+, B8 to B1, and B-. The bottom diagram shows a 24S configuration with connections for B+, B24 to B1, and B-.
6.3. Interface Definition
The BMS features various interfaces for communication and control:

Image: JIKONG V19 Smart BMS interface ports. This model (JK-B2A8S20P-HC) includes NTC, UART/GPS (Customized), RS485/CAN (Customized), Display/Switch, ACC (Customized), and a Sampling Port. It also indicates a Heating Cable connection.

Image: JIKONG V19 Smart BMS external connections. This diagram shows how the NTC, RS485 converter, GPS, Switch, 4.3" LCD, and 2.5" LCD connect to the BMS, along with the Heating Cable.
| Connector Type | Pin Name | Description |
|---|---|---|
| XH-10AW-2.54 (Balance & Acquisition) | B- | Total negative battery |
| B1 | The first battery positive | |
| B2 | The second battery positive | |
| B3 | The third battery positive | |
| B4 | The fourth battery positive | |
| B5 | The fifth battery positive | |
| B6 | The sixth battery positive | |
| B7 | The seventh battery positive | |
| B8 | The eighth battery positive | |
| B+ | Protection board power supply, connected to the battery | |
| A1254WF-2A (Buzzer Interface, Optional) | GND | Buzzer power negative |
| VCC | Buzzer power supply positive | |
| A1254WF-4A (Communication, Optional) | CAN_L | CAN signal negative terminal |
| CAN_H | CAN signal positive terminal | |
| RS485_A | RS485 signal positive terminal | |
| RS485_B | RS485 signal negative terminal | |
| 1.25T-4PWT (GPS) | GND | Power/signal ground |
| HY2.0-4P (4-way External Temperature Interface, Optional) | T5A | Fifth temperature sensor pin A |
| T5B | Fifth temperature sensor pin B | |
| T4A | Fourth temperature sensor pin A | |
| T4B | Fourth temperature sensor pin B | |
| HY2.0-4P (Temperature Interface) | T2A | Second temperature sensor pin A |
| T2B | Second temperature sensor pin B | |
| T1A | First temperature sensor pin A | |
| T1B | First temperature sensor pin B | |
| A1254WF-6A (Display Interface) | VCC | Display power output |
| A | The display RS485 signal is positive | |
| B | Display RS485 signal negative | |
| GND | Negative terminal | |
| K+ | Activate the positive signal | |
| K- | Activation signal negative electrode | |
| A1254WF-3A (Parallel, Optional) | P-status | Parallel module status signal |
| 16AWG-Orange-15CM (Heating Wire, Optional) | HT- | Heater element negative electrode |
| D1 | Bluetooth connection indicator | Steady on when connected, blinking when disconnected. |
| P- | Connect to external load or negative terminal of charger, equipped with M6 screws. | |
| B- | Connect to the negative battery terminal, equipped with M6 screws. |
7. Operating Instructions
7.1. APP Installation and Connection
The JIKONG V19 Smart BMS is controlled via a mobile application available for both Android and iOS devices.
- Download APP:
- iOS: Search for "JIKONG BMS" in the App Store.
- Android: Search for "JK BMS" in the Google Play Store. (Android Version 7 minimum is required).

Image: QR code for JIKONG BMS APP download. Scan this code to get the mobile application.
- Hardware Connection: Connect the protection board and battery pack according to the wiring diagram. Ensure the last power cord is connected to the main positive pole. The total voltage of the battery pack must be greater than 20V (Default BMS) or 10V (4S BMS) before starting up.
- Startup: Use the display activation button or an additional switch to activate the BMS.
- Connect to APP:
- Turn on GPS and Bluetooth on your mobile phone.
- Open the JIKONG APP, click on the top left corner to search for devices.
- Click on the device name to connect. The default password is 1234.

Image: JIKONG Smart BT APP interface. Screenshots show real-time battery data monitoring, support for modifying related parameters, and control of the BMS balance switch, compatible with Android and iOS systems.
- Initial Parameter Setting: For the first startup, parameters need to be set. The default parameter password is 123456. Simply set the number of units (battery strings) and battery type (LiFePo4, Li-ion, LTO).
- Check Battery Status: After setting parameters, return to the real-time status page to check the battery status. Ensure no error messages are prompted. Blue indicates the highest voltage, and red indicates the lowest voltage.
7.2. Device Activation
Before powering on the protection board, double-check all balance cable connections and ensure P- and B- are correctly wired. Confirm the protection board is securely fixed to the battery core. Incorrect connections can lead to abnormal operation or damage.
The protection board does not have a power-on control switch. It is designed for charging activation mode: the charger voltage must be 2V higher than the battery voltage. After battery assembly, connect the charger to activate the BMS.
Alternatively, the BMS can be activated via a key or display. Users with an optional display screen and button can simply connect the cable to the display interface and press the button to activate.
7.3. Active Equalization
The BMS uses active equalization to transfer energy from high-voltage cells to low-voltage cells. Users can set the balance trigger pressure difference (mV) in the APP's parameter settings. Equalization automatically activates when the voltage difference between any two battery strings exceeds the set value and turns off when it falls below the set value. The default balance current is 1A/2A. It is recommended that the balance current does not exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP's BMS control page.
7.4. Heating Function (Optional)
If your BMS model includes the heating function, it can protect the battery in low-temperature conditions. The heating function is activated by detecting battery temperature and is combined with low-temperature protection during charging. The designed heating current is 20A.
- The heating function is achieved by detecting the battery temperature, combined with low-temperature protection during charging, and the status of the charger to achieve electricity pool heating control.
- Not all BMSs support the connection heating function; only BMSs with "Heat" in their models do.
- The heating interface requires an external heating film or charger. The green cable connects to the heating film, and the red and black cables connect to the charger. The maximum heating power is 3A, and the maximum heating voltage is 100V.
- Heating is activated when the battery temperature is lower than the low-temperature protection temperature for charge.
- If connecting a heating film, the APP will activate heating, consuming battery power.
- Heating via the charger is related to the protection board hardware and charger. Confirm technical status before ordering.
7.5. Smart Energy Working Mode Switching

Image: JIKONG Smart BMS energy working mode switching. This diagram illustrates four modes: Storage Mode (BMS does not consume battery pack current), Normal Working Mode (BMS returns to normal operation when charger is inserted), Shutdown (automatic shutdown when cell voltage is below shutdown voltage), and Standby Mode (automatic entry after set time if no charge/discharge current).
- Storage Mode: In transportation, storage, offline, or wireless transmission off mode, the BMS is in storage mode and does not consume battery pack current.
- Normal Working Mode: When the charger is inserted in storage mode and off mode, the BMS immediately returns to normal working mode, and all protection, equalization, and communication functions return to normal working.
- Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage. The BMS automatically shuts down when a cell falls below the shutdown voltage.
- Standby Mode: When the battery pack is in the static state (no charge and discharge current) and no equilibrium current, the BMS will automatically enter standby mode after the set time (1-30 days can be set) is exceeded.
8. Maintenance
To ensure the longevity and optimal performance of your JIKONG V19 Smart BMS, follow these general maintenance guidelines:
- Regular Checks: Periodically check all wiring connections for tightness and signs of wear or corrosion.
- Software Updates: Keep the mobile APP updated to the latest version to benefit from new features and bug fixes.
- Environmental Conditions: Operate the BMS within its specified temperature range (-30°C to 70°C). If operating in extreme cold, utilize the heating function.
- Cleaning: Keep the BMS unit clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Storage: If storing the battery pack with the BMS for an extended period, ensure it enters Storage Mode or Intelligent Sleep mode to minimize power consumption.
9. Troubleshooting
If you encounter issues with your JIKONG V19 Smart BMS, refer to the following common problems and solutions:

Image: JIKONG BMS FAQ, addressing common issues and their solutions.
9.1. Common Issues and Solutions
- Do not turn on:
- Ensure that the last "B+" line of the cable has been connected to the positive pole of the battery.
- Start up after charging and ensure that the charger voltage is greater than 4V of the battery pack voltage.
- Check whether the charger has voltage output.
- Inaccurate voltage:
- Measure the actual total pressure of the battery pack with a multimeter and fill the actual total pressure in the "voltage calibration" on the parameter setting page.
- Inaccurate current:
- B- and P- of the protection board are two 7awg wires, both of which need to be connected in parallel, otherwise it will lead to current error.
- Measure the actual current of the battery pack with a clamp meter and fill the actual current into the "current calibration" on the parameter setting page; the larger the actual current, the higher the calibration accuracy.
- Inaccurate capacity:
- An initial capacity estimated according to the monomer voltage when the protection board is powered on for the first time, which is inaccurate.
- After the protection board is discharged to the cut-off voltage and then fully charged, the capacity is calibrated, and the charging process cannot be interrupted.
- The designed string number is inconsistent with the actual string number:
- Check whether the "unit quantity" in the parameter setting is set correctly.
- If there is no voltage in two or more strings in the middle, check whether the acquisition cable falls off.
10. User Tips
No specific user tips were provided in the available data. Always refer to the official manual for the most accurate and up-to-date information.
11. Certifications
The JIKONG V19 Smart BMS is certified to meet international safety and environmental standards, ensuring product quality and reliability.

Image: JIKONG BMS Product Certifications, displaying certificates for RoHS, FCC, and CE compliance.
- CE: Conforms to European Union safety, health, and environmental protection requirements.
- FCC: Complies with Federal Communications Commission regulations for electronic devices.
- RoHS: Restricts the use of hazardous substances in electrical and electronic equipment.