Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your F25 Electric Sport Glider Balsawood KIT 2500mm AION-25. Designed for enthusiasts aged 14 and above, this balsawood kit offers a rewarding building experience and excellent outdoor flying performance. Please read all instructions carefully before beginning assembly and operation to ensure safe and enjoyable use.
Specifications

Figure 1: F25 2.5M AION Glider Specifications Overview
| Feature | Detail |
|---|---|
| Wingspan | 2500mm |
| Length | 1255mm |
| Takeoff Weight | ~1.1kg |
| Wing Area | 50.8dm² |
| Wing Load | 20.6g/dm² |
| Material | Balsawood |
| Recommended Age | 14+ years |
| Control Channels | ≥6 channels |
| Flight Time | 5-10 minutes (powered flight) |
| Use Environment | Outdoor |
| Remote Control | Yes |
| Controller Mode | MODE1, MODE2 |
| Batteries Included | No |
Suggested Equipment (Not Included)
- Motor: M2216 900-1100KV
- ESC: 20-30A
- Folding Propeller: 10-11 inch
- Servos: 9g * 6pcs
- Extension Wire: 50cm * 2pcs
- Receiver (RX): ≥6CH
- Battery: 3S 2200-2800mAh LiPo
Setup and Assembly
The F25 Electric Sport Glider is a balsawood kit requiring assembly. The package includes the balsawood parts, hardware, and decals. You will need to supply your own tools, adhesives, covering material, and electronic components (motor, ESC, servos, receiver, battery).

Figure 2: Kit Contents Overview

Figure 3: Detailed Kit Components
General Assembly Steps:
- Unpack and Inspect: Carefully unpack all components. Verify that all parts are present and undamaged against the included parts list.
- Fuselage Assembly: Begin by assembling the fuselage sections according to the detailed instructions provided in the operating manual. Use appropriate adhesives for balsawood construction.
- Wing Assembly: Assemble the wing ribs and spars to form the wing structure. Ensure symmetry and proper dihedral (if applicable).
- Tail Section Installation: Attach the horizontal and vertical stabilizers to the fuselage.
- Electronic Component Installation: Install the motor, ESC, servos, and receiver into their designated locations within the airframe. Ensure all wiring is neatly routed and secured.
- Control Surface Linkages: Connect the servos to the ailerons, elevator, and rudder using the provided linkages. Verify smooth and free movement of all control surfaces.
- Covering: Once the airframe is fully assembled and all electronics are installed and tested, apply your chosen covering material (e.g., heat-shrink film) to the entire glider. Ensure a taut and wrinkle-free finish for optimal aerodynamics.
- Center of Gravity (CG) Adjustment: Crucially, balance the glider to the recommended Center of Gravity (CG) point. This typically involves adjusting the battery position. An incorrectly balanced glider will be unstable and difficult to fly.
- Final Checks: Before flight, perform a thorough check of all connections, control surface movements, and structural integrity.
Operating Instructions
Pre-Flight Checks:
- Battery: Ensure the flight battery and transmitter battery are fully charged.
- Control Surfaces: Verify that all control surfaces (ailerons, elevator, rudder) move freely and in the correct direction relative to your transmitter inputs.
- Center of Gravity: Confirm the glider's CG is correctly set.
- Radio Range: Perform a range check of your radio system to ensure reliable control.
- Propeller: Check that the propeller is securely attached and free from damage.
- Structural Integrity: Inspect the entire airframe for any damage, loose parts, or cracks.
Launching:
The F25 glider is typically hand-launched. Hold the glider firmly, engage the motor, and gently push it forward into the wind with a slight upward angle. Avoid throwing it forcefully. For best results, launch into a gentle headwind.
Controlling the Glider:
This glider uses 6 channels, allowing for precise control over ailerons, elevator, rudder, and motor throttle. Familiarize yourself with your transmitter's MODE1 or MODE2 configuration. Practice gentle inputs, especially during initial flights. Utilize thermals for extended gliding flights, reducing motor usage to conserve battery.
Landing:
Approach the landing area into the wind. Reduce throttle and gradually decrease altitude. Use elevator and rudder for directional control. Aim for a gentle, controlled touchdown on the main landing gear (if equipped) or fuselage. Avoid steep descents or high-speed landings.
Safety Guidelines:
- Recreational Use Only: This product is intended for recreational use.
- Legal Compliance: Be aware of and comply with all relevant laws and regulations regarding drone/plane operation in your country or area. Illegal modification of aircraft is prohibited.
- Safe Flying Area: Always fly in open areas, away from people, buildings, power lines, and other obstacles.
- Weather Conditions: Do not fly in strong winds, rain, or other adverse weather conditions.
- Visual Line of Sight: Always maintain visual line of sight with your glider.
- Respect Others: Be mindful of others and avoid disturbing wildlife.
Maintenance
Post-Flight Inspection:
- Inspect the airframe for any damage, especially to the balsawood structure and covering.
- Check all control linkages for looseness or wear.
- Examine the propeller for cracks or chips.
- Ensure all electronic components are securely mounted.
Cleaning:
Wipe down the glider with a soft, dry cloth after each flight to remove dirt and debris. Avoid using harsh chemicals that could damage the covering or balsawood.
Storage:
Store the glider in a cool, dry place, away from direct sunlight and extreme temperatures. Protect it from physical damage during storage. Disconnect the flight battery when not in use.
Repairs:
Minor damage to the balsawood structure can often be repaired using CA glue or epoxy. Tears in the covering film can be patched with matching material or repair tape. For significant structural damage, consider replacing the affected part or seeking expert advice.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Glider won't fly straight/is unstable | Incorrect Center of Gravity (CG); Warped wing/tail; Control surface trim issues | Adjust CG by moving battery; Check for warps and correct; Adjust transmitter trims or mechanical linkages. |
| Motor not spinning | Disconnected battery; Faulty ESC/motor; Receiver not bound; Throttle cut engaged | Check battery connection; Inspect ESC/motor wiring; Re-bind receiver; Disengage throttle cut. |
| Loss of control/short range | Low transmitter/receiver battery; Interference; Damaged antenna | Charge batteries; Fly in a different location; Inspect and repair antenna. |
| Poor gliding performance | Heavy build; Rough covering; Incorrect CG; Lack of thermals | Ensure light build; Smooth covering; Verify CG; Seek better thermal conditions. |
User Tips
- Adhesive Choice: For balsawood construction, use cyanoacrylate (CA) glue for quick bonds on non-stressed joints, and epoxy for high-stress areas like wing roots and motor mounts. Always ensure good ventilation.
- Sanding for Aerodynamics: Take your time to sand all balsawood parts smooth. A smooth finish significantly reduces drag and improves flight performance.
- Covering Application: When applying covering film, ensure it is taut and free of wrinkles. Proper covering not only adds to the aesthetics but also provides structural rigidity and aerodynamic efficiency.
- Accurate Center of Gravity (CG): The most critical step for a stable flying glider is setting the correct Center of Gravity. Follow the manual's recommended CG point precisely. Small adjustments can make a big difference in flight characteristics.
- Pre-Flight Checklist: Develop a routine pre-flight checklist and stick to it. This includes checking battery levels, control surface movements, radio range, and structural integrity before every flight.
Warranty and Support
This product is a balsawood kit designed for assembly by the user. The package includes operating instructions to guide you through the building process.
For any questions regarding assembly, missing parts, or technical support, please contact the seller or manufacturer directly. Specific warranty details, if any, would be provided at the point of purchase or within the detailed operating instructions included with the kit.
Statement of Compliance
⚠️ Disclaimer:
For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.