Dancing Wings Hobby T11

Contents

DW Hobby 1.0M Air Kart Delta Wing RC Airplane Balsa Kit Instruction Manual

Model: T11 | Brand: Dancing Wings Hobby

1. Introduction

This manual provides detailed instructions for the assembly, setup, and operation of your DW Hobby 1.0M Air Kart Delta Wing RC Airplane Balsa Kit. This kit is designed for hobbyists aged 14 and above with varying skill levels (Beginner, Intermediate, Expert). Please read this manual thoroughly before beginning assembly or operation to ensure safe and enjoyable use.

Safety Warning

⚠️ For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

2. Package Contents

The DW Hobby 1.0M Air Kart Delta Wing RC Airplane is available in several kit configurations. Please verify the contents of your package against the list below based on the model you purchased.

Kit Options:

  • T1101 Balsa KIT: Includes the balsa wood airframe components and necessary hardware for assembly.
  • T1101B Balsa KIT + Film: Includes the T1101 Balsa KIT plus covering film (e.g., orange 2M, apple green 2M).
  • T1104 Balsa KIT + Electronics: Includes the T1101 Balsa KIT along with essential electronic components:
    • Motor: MM2212 1100kv
    • Propeller: 9-inch
    • ESC: 30A
    • Servos: 9g*2pcs
  • T1104B Balsa KIT + Electronics + Film: A comprehensive package including the T1101 Balsa KIT, electronic components (Motor, Propeller, ESC, Servos), and covering film (e.g., orange 2M, apple green 2M).
T1101 Balsa KIT components
Figure 2.1: T1101 Balsa KIT components (example: white color option)
T1101B Balsa KIT with covering film
Figure 2.2: T1101B Balsa KIT with covering film (example: purple color option)
T1104 Balsa KIT with electronics
Figure 2.3: T1104 Balsa KIT with electronics (example: brown color option)
T1104B Balsa KIT with electronics and covering film
Figure 2.4: T1104B Balsa KIT with electronics and covering film (example: orange color option)

3. Specifications

FeatureSpecification
TypeAirplane (Delta Wing)
Brand NameDancing Wings Hobby
ModelT11
MaterialWood (Balsawood)
Wingspan1000mm (40 inches)
Length690mm (27 inches)
Takeoff Weight~0.8kg+
Recommended MotorMM2212 1100kv
Recommended ESC3S 30A
Recommended LiPo Battery3S 1300-2800mAh
Recommended Propeller8-9 inch
Recommended Servos9g*2pcs
Recommended Receiver>=3CH
Control Channels3 channels
Controller ModeMODE1, MODE2
Indoor/Outdoor UseOutdoor
Recommended Age14+ years
Is ElectricNo battery (Electric power system required)
Is Batteries IncludedNo
Flight Time (approx.)5~10 minutes (with recommended setup)
T11 Balsawood KIT specifications overview
Figure 3.1: T11 Balsawood KIT specifications overview

4. Assembly Instructions

The DW Hobby Air Kart is a balsa wood kit, requiring careful assembly. This process involves cutting, gluing, and sanding balsa wood parts, followed by covering the airframe. Detailed step-by-step instructions and diagrams are typically included within your kit packaging. Please refer to these specific instructions for precise assembly.

General Assembly Steps:

  1. Preparation: Unpack all components and familiarize yourself with the parts and the provided plans/diagrams. Ensure you have all necessary tools (e.g., hobby knife, sandpaper, wood glue, covering iron).
  2. Frame Construction: Carefully cut out the balsa wood parts as indicated in the plans. Assemble the main wing and fuselage sections using wood glue, ensuring all joints are strong and square. Allow adequate drying time for the glue.
  3. Sanding: Once the frame is dry, lightly sand all surfaces to remove any rough edges and ensure a smooth aerodynamic profile.
  4. Covering (if applicable): If your kit includes covering film, apply it according to the film manufacturer's instructions. This typically involves using a heat iron to shrink the film onto the balsa frame, creating a durable and lightweight skin.
  5. Control Surface Installation: Install the control horns and hinges for the elevons (elevator/aileron combination) as per the kit instructions.
Balsa kit frame top view
Figure 4.1: Balsa kit frame, top view
Balsa kit frame close-up of wing structure
Figure 4.2: Close-up of the balsa wing structure during assembly
In-progress build of the balsa kit
Figure 4.3: An in-progress build of the balsa kit, showing the internal structure

5. Electronics Installation

If your kit includes electronic components or if you are supplying your own, follow these general guidelines for installation. Always refer to the specific instructions provided with your electronic components for detailed wiring and setup.

  1. Motor Installation: Mount the MM2212 1100kv motor securely to the designated motor mount at the rear of the aircraft. Ensure the propeller is correctly oriented and balanced.
  2. ESC Installation: Connect the 30A ESC to the motor and the receiver. Secure the ESC in a location with good airflow to prevent overheating.
  3. Servo Installation: Install the two 9g servos into their respective bays. Connect the servo linkages to the elevons, ensuring smooth and free movement.
  4. Receiver Installation: Mount your 3-channel (or more) receiver securely within the fuselage. Connect the servos and ESC to the appropriate channels on the receiver.
  5. Battery Placement: Position the 3S 1300-2800mAh LiPo battery in the designated battery compartment. Ensure it is secured to prevent shifting during flight. Proper battery placement is crucial for achieving the correct Center of Gravity (CG).

6. Pre-Flight Checks

Before every flight, perform the following checks to ensure safe operation:

  • Control Surfaces: Verify that all control surfaces (elevons) move freely and in the correct direction in response to your transmitter inputs.
  • Battery: Ensure the flight battery is fully charged and securely installed.
  • Radio Range: Perform a range check of your radio system according to your transmitter's manual.
  • Center of Gravity (CG): Confirm the aircraft's CG is within the recommended range. An incorrect CG can lead to unstable flight.
  • Propeller: Check that the propeller is securely attached and free from damage.
  • Visual Inspection: Inspect the entire aircraft for any loose parts, damage, or wear.

7. Operating Instructions

The DW Hobby Air Kart is designed for outdoor flight. Always choose a large, open area free from obstacles, people, and animals. Avoid flying in windy conditions, especially during your first flights.

Launching:

The Air Kart is typically hand-launched. Hold the aircraft firmly, apply about 70-80% throttle, and gently toss it forward and slightly upwards into the wind. Do not throw it forcefully downwards.

Flying:

Use the elevons to control pitch (up/down) and roll (left/right). Throttle controls speed. Start with gentle control inputs until you become familiar with the aircraft's response. Maintain a safe altitude and distance from yourself and others.

Landing:

Approach the landing area at a reduced throttle setting. Gradually decrease altitude and gently flare (pull up on the elevons) just before touchdown to slow the aircraft and achieve a smooth landing on its belly.

Video 7.1: RC plane flying demonstration. This video shows the T11 Delta Wing in flight, demonstrating its maneuverability and stability.
T11 Delta Wing RC plane in flight
Figure 7.1: The T11 Delta Wing RC plane in flight (green and orange color scheme).
T11 Delta Wing RC plane flying overhead
Figure 7.2: The T11 Delta Wing RC plane flying overhead (orange color scheme).

8. Maintenance

Regular maintenance will prolong the life of your RC airplane:

  • Post-Flight Inspection: After each flight, inspect the airframe for any damage, cracks in the balsa wood, or tears in the covering film. Repair as needed.
  • Electronics Check: Ensure all electronic components (motor, ESC, servos, receiver) are securely mounted and their connections are firm.
  • Battery Care: Store LiPo batteries in a cool, dry place at storage voltage. Do not overcharge or over-discharge.
  • Cleaning: Keep the aircraft clean from dirt, grass, and debris.
  • Storage: Store the aircraft in a safe place where it won't be damaged, ideally in its original box or a dedicated carrying case.
Product packaging for storage
Figure 8.1: Original product packaging, suitable for safe storage of the kit components.

9. Troubleshooting

Here are some common issues and their potential solutions:

  • Aircraft does not respond to controls: Check transmitter battery, receiver connection, servo connections, and ensure the aircraft is powered on.
  • Aircraft flies erratically: Re-check Center of Gravity (CG), ensure control surfaces are moving correctly and freely, and verify no damage to the airframe.
  • Motor not spinning: Check battery connection, ESC connection to motor and receiver, and ensure ESC is armed correctly.
  • Short flight time: Ensure battery is fully charged, check for excessive drag or inefficient propeller, and verify battery capacity is sufficient.

10. User Tips

  • Take Your Time with Assembly: As this is a balsa kit, careful and patient assembly will result in a more robust and better-flying model. Pay close attention to the covering process for a smooth, professional finish.
  • Balance is Key: Proper balancing (Center of Gravity) is critical for stable flight. Spend time ensuring your aircraft is balanced correctly before its maiden flight.

11. Warranty and Support

For any questions, technical assistance, or support regarding your DW Hobby 1.0M Air Kart Delta Wing RC Airplane Balsa Kit, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Compliance Statement: ⚠️ For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

© 2023 Dancing Wings Hobby. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.