AWithZ U2

Contents

AWithZ U2 Portable Spot Welding Machine User Manual

Model: U2 | Brand: AWithZ

1. Introduction

Thank you for choosing the AWithZ U2 Portable Spot Welding Machine. This handheld, compact device is designed for precision spot welding, offering 90 levels of power adjustment and a dual-pulse output for efficient and reliable welds. It features a convenient Type-C charging interface and is suitable for a variety of applications, including mobile phone battery transplantation, 18650 battery pack assembly, and general DIY maintenance. Please read this manual thoroughly before use to ensure safe and optimal operation.

2. Important Safety Information

Always observe the following safety precautions to prevent injury or damage to the device:

  • Spot welding is an engineering discipline; the effect may vary based on angle, strength, and surface flatness.
  • When welding, gently place the welding pen on the nickel plate. Do not press the welding pen hard.
  • Ensure the welding distance between the two welding needles is appropriate. If the welding point is black, increase the gear. If the melt pool is too small, increase the gear.
  • Before formal welding, practice on scrap material (e.g., a blade, stainless steel bowl, or other large iron or stainless steel surfaces) to familiarize yourself with the process and achieve smoother welds.
  • Keep the welding needle and nickel battery flat and clean during welding. The nickel plate and battery must be tightly attached and not suspended; otherwise, a hole may be left on the nickel plate.
  • After multiple uses, the welding needle may oxidize. Gently polish the blackened part with a file or sandpaper.
  • During and immediately after welding, the temperature at the welding needle, nickel sheet, and battery welding point is extremely high. Do not touch them to avoid burns.
  • The device is equipped with multiple security algorithms and temperature sensors for protection against: Quality cell issues, Shock, Voltage instability, Short circuits, Low temperature, High temperature, Overcharge, and Overdischarge.
Diagram showing multiple security measures icons

Figure 2.1: Multiple security measures for safe operation.

3. Package Contents

Please check the package for the following items:

  • AWithZ U2 Spot Welding Machine (5000mAh) x 1
  • Welding Pen x 2
  • Sandpaper x 1
  • Charging Cable (Type-C) x 1
  • Nickel Sheet (2 meters) x 1
Image showing the U2 spot welding machine and its included accessories

Figure 3.1: Contents of the AWithZ U2 Spot Welding Machine package.

4. Product Overview

Familiarize yourself with the components and controls of your U2 Spot Welding Machine:

Diagram of the U2 spot welding machine with labeled parts and buttons

Figure 4.1: Interface and buttons of the AWithZ U2 Spot Welding Machine.

  1. Display Screen: Shows temperature, selected gear, trigger time, and continuous welding count.
  2. Switch ON/OFF/Mode Switch: Long press to turn ON/OFF. Short press to switch options on the display.
  3. Adjust Key: Long press for continuous adjustment. Short press for single adjustment of parameters.
  4. Manual Spot Welding Key: Initiates a manual spot weld.
  5. Type-C INPUT Charging Interface: For charging the device (5V/2.1A MAX input).
  6. USB Output: Can be used as a power bank.
  7. Output Port: Connects the spot welding pens.

5. Specifications

Attribute Value
Brand AWithZ
Model U2
Product Name Spot Welder
Battery Type Lithium battery
Capacity 5000mAh
Gear Adjustment 90 power levels
Charging Interface Type-C
Input 5V/2.1A (MAX)
Output Voltage 4.2V (MAX)
Output Current 650A (MAX)
Product Size 15.9 x 9.2 x 2.5 cm (6.26 x 3.62 x 0.98 inches)
Weldable Thickness (Nickel plating, Iron, Steel) 0.025 cm / 0.009 inch (MAX)
Weldable Thickness (Pure Nickel) 0.02 mm / 0.007 inch (MAX)

Note: The above data is manually measured and may have some errors. Please refer to the actual product for accuracy.

Table of product attributes including brand, model, battery, capacity, and dimensions

Figure 5.1: Detailed product attributes.

Diagram showing the dimensions of the U2 spot welding machine

Figure 5.2: Product dimensions.

6. Setup

  1. Charge the Device: Connect the provided Type-C charging cable to the Type-C INPUT (5) on the device and a suitable 5V/2.1A power adapter. The display screen (1) will indicate charging status. The device supports use during charging.
  2. Install Welding Pens: Insert the two professional spot welding pens into the Output Ports (7) on the top of the machine. Ensure they are securely connected.
  3. Power On: Long press the ON/OFF/Mode Switch (2) for 2 seconds to turn on the device. The display screen (1) will light up, showing current temperature, selected gear, trigger time, and continuous welding count.
Step-by-step guide for setting up the spot welding machine and connecting pens

Figure 6.1: Initial setup steps including connecting welding pens.

Main product image showing the U2 spot welding machine with its display and features

Figure 6.2: AWithZ U2 Spot Welding Machine.

7. Operating Instructions

7.1. Power Adjustment

The U2 Spot Welding Machine offers 90 levels of output power adjustment. This wide adaptability range allows you to find the suitable gear for different welding objects and materials.

  • Short press the ON/OFF/Mode Switch (2) to cycle through options on the display.
  • Short press the Adjust Key (3) for single-step adjustment of the selected parameter (e.g., welding gear).
  • Long press the Adjust Key (3) for continuous adjustment of the selected parameter.
Diagram illustrating the 90-level output power adjustment and display interface

Figure 7.1: 90-level output power adjustment interface.

Chart showing weldable material types and their maximum thicknesses

Figure 7.2: Weldable materials and their maximum thicknesses.

7.2. Welding Process

  1. Prepare the Workpiece: Ensure the battery and nickel sheet are clean and flat. The surface of the battery and nickel plate must be free from contaminants and properly adhered.
  2. Position the Welding Pens: Hold a spot welding pen in each hand. Maintain an appropriate distance between the welding needles.
  3. Initiate Weld: Gently press the welding pens onto the nickel sheet, which is placed on the battery. The device will automatically detect contact and output a dual pulse.
  4. Check Welding Effect: After welding, inspect the joint. A good weld should be firm and clean.
Six-step visual guide for the spot welding process

Figure 7.3: Step-by-step guide for the spot welding process.

7.3. Dual Pulse Output

AWithZ products are equipped with a dual pulse welding output design. This process includes a deoxygenation pulse before the formal welding pulse to improve the welding effect and ensure stronger, firmer welds.

Graph illustrating the dual pulse welding output, showing deoxygenation and welding pulses

Figure 7.4: Dual pulse welding output waveform.

7.4. Applications

  • Mobile Phone Battery Transplantation: Suitable for various brands of mobile phone batteries, not limited by battery size and dimensions.
  • 18650 Battery Pack Assembly: Welding and assembling various cylindrical batteries, such as common 18650/26650/32650, etc.
  • DIY Assembly and Maintenance: Ideal for general DIY assembly and equipment maintenance tasks.
Images demonstrating various applications of the spot welding machine

Figure 7.5: Common applications of the AWithZ U2 Spot Welding Machine.

8. Maintenance

  • Welding Needle Care: After multiple uses, the welding needles may oxidize, causing them to blacken. Use a fine file or sandpaper to gently polish off the blackened part to restore optimal conductivity and welding performance.
  • Cleaning: Keep the device and welding pens clean and free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquids or abrasive cleaners.
  • Storage: Store the spot welding machine in a cool, dry place away from direct sunlight and moisture when not in use.

9. Troubleshooting

If you encounter issues during welding, refer to the following common problems and solutions:

Visual guide showing correct and incorrect welding techniques and common errors

Figure 9.1: Examples of correct and incorrect welding.

Problem Possible Cause Solution
Poor weld / Black welding point Welding distance too close, insufficient power (gear too low), oxidized welding needles, material corrosion. Adjust welding distance, increase welding gear, clean welding needles with sandpaper, ensure materials are clean.
Hole in nickel plate / Melt pool too small Excessive power (gear too high), welding pens pressed too hard, nickel plate/battery not flat or suspended. Decrease welding gear, apply gentle pressure, ensure nickel plate and battery are flat and tightly attached.
No weld / Weak weld Single pen spot welding (not dual contact), non-misalignable batteries, material too thick, material not adhered properly. Ensure both welding pens make contact, use appropriate batteries, check material thickness against specifications, ensure proper adhesion.
Device not turning on Low battery, power button not pressed correctly. Charge the device fully. Long press the ON/OFF/Mode Switch for 2 seconds.

10. User Tips

No specific user tips from reviews or Q&A were provided. However, general best practices for spot welding include:

  • Always perform test welds on similar scrap material before working on your main project to fine-tune the power settings.
  • Maintain consistent pressure and contact angle with both welding pens for uniform welds.
  • Keep the welding area well-ventilated.

11. Warranty and Support

For warranty information, technical support, or any questions regarding your AWithZ U2 Portable Spot Welding Machine, please contact the seller or refer to the product listing on the platform where it was purchased. Keep your purchase receipt as proof of purchase.

© 2024 AWithZ. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.