FMS Freewing 120A electronic speed controller

Contents

Freewing 120A Electronic Speed Controller User Manual

Model: Freewing 120A Electronic Speed Controller

1. Introduction

This manual provides essential information for the safe and efficient operation of your Freewing 120A Electronic Speed Controller (ESC). This high-performance brushless ESC is designed for remote control aircraft, offering a continuous current of 120A, an instantaneous current of 140A, and compatibility with 3-8S LiPo batteries. It features a BEC with three adjustable voltage levels (5.2V/6V/7.4V) and a thrust reverser brake function.

Freewing 120A ESC with key features highlighted

Overview of the Freewing 120A Electronic Speed Controller, highlighting its 120A continuous current, 140A instantaneous current, 3-8S input voltage, and adjustable 5.2V/6V/7.4V BEC output with thrust reverser brake function.

2. Safety Information

  • Always read the entire manual before operating the ESC.
  • Ensure all connections are correct and secure before applying power. Incorrect wiring can cause damage to the ESC, motor, battery, or other components.
  • Insulate all exposed wires and solder joints to prevent short circuits.
  • Keep the ESC away from water, moisture, and extreme temperatures.
  • Use only compatible batteries and motors within the specified voltage and current limits.
  • High-power systems can be dangerous. Always exercise caution and keep hands clear of rotating propellers or moving parts.
  • Disconnect the battery immediately after use and during storage.

3. Package Contents

  • 1x Freewing 120A Electronic Speed Controller

4. Specifications

Parameter Value
Product Name Electronic governor (brushless electric)
Electric Tune 120A
Instantaneous Current 140A
Input Voltage (V) 3-8S LiPo
Use Plug EC5
BEC Output 5.2V/6V/7.4V (three adjustable)
Thrust Reverser Brake Function Yes
Size (L*W*H) 77*35*19mm
Weight 93g
Material Composite Material
Recommended Use Vehicles & Remote Control Toys, Airplanes
Table of basic product parameters and precautions

Detailed specifications of the Freewing 120A ESC, including electrical and physical parameters.

5. Setup and Installation

5.1 Wiring Diagram

Refer to the diagram below for proper connection of the ESC to your motor, battery, and receiver/flight controller.

Wiring diagram for Freewing 120A ESC showing connections to motor, battery, and receiver/flight controller

Schematic diagram illustrating the connections between the Electronic Governor (ESC), Motor, Battery, and the receiver/flight controller.

5.2 Signal Line Description

  1. Throttle Signal Line (White, Red, Black long line): Insert this into the receiver's throttle channel or the flight control throttle channel. The white line transmits the throttle signal, while the red and black lines are the output lines of the BEC (Battery Eliminator Circuit), providing power to the receiver and servos.
  2. Thrust Reverser Brake Signal Line (Yellow): If the reverse brake function is to be used, this yellow signal line must be connected to another free channel on your remote controller. This channel will then be used to control the activation and deactivation of the reverse brake function.
  3. Programming Line (White, Red, Black short line): This line is used to connect an LED programming setting box for adjusting various parameters of the ESC.

5.3 Precautions for Installation

The length of the electric tuning line (motor wires) can vary for different aircraft models. It is crucial to make appropriate adjustments based on your specific aircraft's configuration. Always refer to the configuration instructions provided with your aircraft or contact customer service for guidance if unsure.

6. Operating Instructions

6.1 Initial Power-Up

  1. Ensure all connections (motor, battery, receiver) are secure and correct.
  2. Turn on your remote control transmitter and set the throttle stick to the lowest position.
  3. Connect the battery to the ESC. The ESC will emit a series of beeps indicating cell count and readiness.
  4. Slowly advance the throttle to test motor rotation.

6.2 BEC Voltage Adjustment

The ESC's BEC provides three adjustable voltage outputs: 5.2V, 6V, and 7.4V. This allows you to select the appropriate voltage for your receiver and servos. The adjustment method typically involves using the dedicated programming line and an LED programming box (sold separately) to cycle through the options. Refer to the programming box manual for detailed instructions.

6.3 Thrust Reverser Brake Function

If you have connected the yellow thrust reverser brake signal line to a free channel on your receiver, you can activate this function via your remote control. This feature allows for controlled braking and reverse thrust, useful for certain aircraft maneuvers or landing. Consult your remote control's manual for assigning and operating this channel.

6.4 Programming Parameters

The short programming line is used with an external LED programming setting box to customize various ESC parameters such as timing, brake type, low voltage cutoff, and more. Connect the programming box to this line and follow the instructions provided with the programming box to adjust settings.

7. Maintenance

  • Regularly inspect all wires and connectors for signs of wear, damage, or corrosion.
  • Keep the ESC clean and free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning.
  • Ensure adequate airflow around the ESC during operation to prevent overheating.
  • Store the ESC in a dry, cool environment when not in use.

8. Troubleshooting

  • Motor not spinning: Check battery connection, ESC to motor connections, and receiver connection. Ensure throttle is calibrated correctly.
  • Erratic motor behavior: Verify all signal connections are secure. Check for interference or damaged wires. Recalibrate throttle range.
  • ESC overheating: Ensure proper ventilation. Check if the motor is oversized or if the propeller is too large, causing excessive current draw.
  • No power to receiver/servos: Check BEC output voltage setting and ensure the BEC wires are correctly connected to the receiver.

9. User Tips

  • This ESC supports 3-8S battery configurations, making it suitable for high-power applications like 8-cell Electric Ducted Fan (EDF) systems. Always ensure your motor and battery are compatible with the ESC's specifications to prevent damage.
  • For optimal performance and longevity, consider using a separate UBEC (Universal BEC) if your setup involves many high-draw servos, to offload the power supply from the ESC's internal BEC.

10. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.