1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your maXpeedingrods 2.5 inch Suspension Lift Kit. This kit is designed to increase the ground clearance of your vehicle's suspension, allowing for the installation of larger tires and enhancing off-road performance. The kit also levels the front of the vehicle with the rear, improving overall stance.
The included shocks feature a high-pressure nitrogen-filled design, natural rubber bushings, and a corrosion-resistant metallic silver paint finish, engineered to provide a balance of off-road capability and smooth on-road ride quality.
2. Vehicle Fitment
This suspension lift kit is compatible with the following vehicle models:
- Toyota Tundra 2WD: 2000-2006
- Toyota Tundra 4WD: 2000-2006
Note: Strut replacement is for 4WD models ONLY.
3. Package Contents
Please verify that all components listed below are present in your package before beginning installation.
Front Components:
- Upper Strut Extensions (x2)
- Hardware for Front Installation
Rear Components:
- 2 inch Lift Blocks (x2)
- U-bolts (x4)
- Brake Line Bracket
- Proportioning Valve Bracket
- Hardware for Rear Installation
Shock Absorbers:
- Premium Series Rear Shock Absorbers (x2)
4. Setup and Installation
The maXpeedingrods 2.5 inch Suspension Lift Kit features an easy bolt-on installation process. The estimated installation time is approximately 3-4 hours. While designed for straightforward installation, suspension modifications can be complex and require specific tools and knowledge. Professional installation is highly recommended to ensure proper fitment, safety, and vehicle alignment.
Safety Warning:
- Always use appropriate safety gear, including eye protection and gloves.
- Ensure the vehicle is securely supported on jack stands before working underneath.
- Do not attempt installation if you are not familiar with vehicle suspension systems.
- After installation, a professional wheel alignment is mandatory to prevent premature tire wear and ensure safe vehicle handling.
Key Components and Materials:
- Front Strut Extensions: Made from Billet 6061 Aluminum.
- Rear Lift Blocks: Feature a grey powder coat finish.
- U-bolts: Zinc plated for rust and corrosion prevention.
- Shock Absorbers: Equipped with natural rubber bushings and a frosted surface treatment for durability.
5. Operating Considerations
After installing the lift kit, your vehicle will experience increased ground clearance, allowing for the fitment of larger tires and an enhanced off-road driving experience. The kit is designed to maintain factory ride quality while providing these benefits.
The twin-tube design of the shock absorbers contributes to a comfortable ride, balancing performance with daily driving needs.
6. Maintenance
To ensure the longevity and optimal performance of your suspension lift kit, regular maintenance is recommended:
- Regular Inspection: Periodically inspect all components of the lift kit, including bolts, nuts, bushings, and shocks, for any signs of wear, damage, or loosening.
- Cleaning: Keep the suspension components clean, especially after off-road use, to prevent accumulation of dirt and debris that can accelerate wear.
- Corrosion Prevention: The components are designed with protective coatings (powder coat, zinc plating) to resist oxidation and rusting. However, in harsh environments, additional rust preventative measures may be beneficial.
- Shock Absorbers: Check shocks for leaks or damage. Replace if necessary.
- Alignment: Re-check wheel alignment periodically, especially after severe off-road driving, to ensure proper vehicle handling and tire wear.
7. Troubleshooting
If you experience any issues with your suspension lift kit, such as unusual noises, changes in ride quality, or uneven vehicle stance, it is recommended to:
- Re-inspect all installed components for proper torque and fitment.
- Consult with a qualified automotive technician for diagnosis and repair.
- Contact maXpeedingrods technical support for assistance.
8. Specifications
| Attribute | Value |
|---|---|
| Lift Height (Front) | 2.5 inches |
| Lift Height (Rear) | 2 inches |
| Estimated Install Time | 3-4 hours |
| Recommended Tire (16" Rim) | 33x10.50R16 Factory 16 6x5.5 |
| Recommended Tire (17" Rim) | 33x10.50R17 Factory 17 6x5.5 |
| Shock Absorber Collapsed Length | 18.7 inches |
| Shock Absorber Extended Length | 28.54 inches |
| Item Weight | 13580g (approx. 29.94 lbs) |
| Item Length | 70cm (approx. 27.56 inches) |
| Item Width | 36.5cm (approx. 14.37 inches) |
| Item Height | 27cm (approx. 10.63 inches) |
| Front Strut Extension Material | Billet 6061 Aluminum |
| Rear Lift Block Finish | Grey Powder Coat |
| U-bolt Finish | Zinc Plating (Rust and Corrosion Prevention) |
9. Warranty and Support
maXpeedingrods provides the following support for this product:
- LIFETIME Technical Support: Assistance with product inquiries and troubleshooting.
- 12-MONTH Limited Warranty: Covers quality-related issues from the date of purchase.
For technical assistance or warranty claims, please refer to the contact information provided by your retailer or on the official maXpeedingrods website.
10. User Tips
- Always perform a professional wheel alignment immediately after installing any lift kit to ensure correct steering geometry and prevent uneven tire wear.
- Consider upgrading to larger tires after installation to fully utilize the increased ground clearance and enhance the aesthetic appeal of your lifted vehicle.
- Regularly check tire pressure, especially with larger tires, to maintain optimal handling and safety.
- Be aware that lifting a vehicle can change its center of gravity, potentially affecting handling characteristics. Drive cautiously until you are accustomed to the new feel of your vehicle.
