WenQia 2202RF

Contents

WenQia 2202RF Universal Wireless Remote Control Switch User Manual

Model: 2202RF | Brand: WenQia

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your WenQia 2202RF 433MHz Universal Wireless Remote Control Switch. This 2-channel RF relay receiver is designed for a wide range of applications, including controlling lights, fans, motors, and garage door openers. Please read this manual carefully before use to ensure proper and safe operation.

WenQia 2202RF Universal Wireless Remote Control Switch with two remote controls

Figure 1: WenQia 2202RF Receiver and Remote Controls

2. Safety Information

  • CAUTION: Disconnect power when installing. Ensure the main power supply is turned off before performing any wiring or installation procedures to prevent electric shock.
  • Signal pairing is required before use.
  • Do not expose the device to excessive moisture or extreme temperatures.
  • Ensure all connections are secure and properly insulated.

3. Product Overview

The WenQia 2202RF is a versatile 2-channel RF relay receiver that operates on 433MHz frequency. It supports both AC 90V-250V and USB 5V-0.5A power inputs, offering flexibility for various applications. The device features a passive output relay (dry contact) with a maximum current of 10A and a maximum load of 2200W.

3.1 Key Features

  • Wide Application: Suitable for controlling lamps, LED lights, AC/DC motors, electric fans, garage door systems, fish pond aerators, blind motors, electric curtains, water pumps, and more.
  • Long Control Distance: Offers a control distance of up to 50 meters in open areas. The signal is stable and can penetrate walls.
  • Multiple Operating Modes: Supports Momentary Mode, Toggle Mode, Latched Mode, Mix Mode, and Motor Toggle Mode.
  • High Compatibility: Compatible with 1527 Learning code and 2262 fixed code remote controls.
  • Expandable: One receiver can be paired with up to 20 remote controls.
Diagram showing wide applications of the remote control switch including lamps, LEDs, AC/DC motors, garage doors, fans, aerators, and blind motors.

Figure 2: Wide Application Examples

4. Specifications

4.1 Relay Receiver Board Parameters

ParameterValue
Working VoltageAC 90V~250V or USB Type-C 5V-0.5A
Input Voltage1V~250V
Output TypePassive output (dry contact)
Quiescent Current<5MA
Max Current10A
Max Load2200W
RF Frequency433MHz (433.92MHz)
Pin ConfigurationNO (Normally Open), COM (Common), NC (Normally Closed)
Working Temperature-30~+80°C
Receiving Sensitivity>-97dbm
Max Remote Controls20 pieces
Support Encoding1527 Learning code / 2262 fixed code
RF Operating ModeASK superheterodyne wireless reception
Receiving RangeOpen space is more than 50 meters
Remote Operating ModesMomentary Mode, Toggle Mode, Latched Mode, Mix Mode, Motor Toggle Mode
Receiver dimensions showing 65mm length, 50mm width, and 24mm height, with USB 5V and AC 90-250V input options and CH1/CH2 passive output relay.

Figure 3: Receiver Dimensions and Power Input

4.2 Remote Controller Parameters

ParameterValue
RF Frequency433MHz
Control Distance50 meters in open space
MaterialPlastic
Support Encoding1527 Learning code
BatteryCR2032 (included)
Size50*30*10mm
Remote control dimensions showing 60x30x10mm and CR2032 3V battery.

Figure 4: Remote Control Dimensions and Battery

5. Setup and Wiring

Before proceeding with installation, ensure the power supply is disconnected. The receiver supports both AC 90-250V and USB 5V-0.5A power inputs. The output is a passive relay (dry contact), meaning it provides a switch closure without supplying power to the connected device. You will need to supply power to your load separately.

5.1 Receiver Terminals

Detailed view of the receiver with labeled terminals: NO (Normally Open), COM (Common), NC (Normally Closed) for each channel, L and N for AC input, and USB Type-C for 5V input. Also shows 1st CH indicator, 2nd CH indicator, Learning Button, and Antenna.

Figure 5: Receiver Terminal Layout

  • L, N: AC 90-250V Power Input
  • USB Type-C: 5V-0.5A Power Input
  • CH1 (NO1, COM1, NC1): Channel 1 Relay Output
  • CH2 (NO2, COM2, NC2): Channel 2 Relay Output
  • NO (Normally Open): Connects to COM when the relay is activated.
  • COM (Common): Common terminal for the relay.
  • NC (Normally Closed): Connects to COM when the relay is deactivated.
  • Learning Button: Used for pairing remote controls and changing operating modes.
  • Antenna: For RF signal reception.

5.2 Wiring Diagrams

Below are common wiring examples. If your application differs or you have questions, please consult a qualified electrician or contact support.

Multiple wiring diagrams for AC Device, 1V-250V, USB Type-C, AC Motor, and DC Motor connections. Each diagram shows the receiver, power input, and load connections.

Figure 6: General Wiring Examples

Wiring diagrams for AC Motor control (garage door) and AC Light control. Shows connections for AC 90-250V input and passive output relays.

Figure 7: AC Motor and AC Light Wiring Examples

6. Operating Modes and Pairing

The receiver supports five different operating modes. To set a mode, you will press the learning button on the receiver a specific number of times, then pair the remote control buttons.

Video 1: Demonstration of Operating Modes (Momentary, Toggle, Latched, Mix, Motor Toggle, Reset)

6.1 Momentary Mode (Press 1 time)

In Momentary Mode, the relay is activated only while the remote button is pressed and held. Releasing the button deactivates the relay.

  1. Setup: Press the learning button on the receiver 1 time. Wait 3 seconds.
  2. Press button "A" on the remote control 1 time.
  3. Press button "B" on the remote control 1 time. Pairing is successful.
  • Press and hold button "A", relay "1" will turn on. Release button "A", relay "1" will turn off.
  • Similarly, button "B" controls relay "2".

6.2 Toggle Mode (Press 2 times)

In Toggle Mode, each press of the remote button toggles the relay state (on/off).

  1. Setup: Press the learning button on the receiver 2 times. Wait 3 seconds.
  2. Press button "A" on the remote control 1 time.
  3. Press button "B" on the remote control 1 time. Pairing is successful.
  • Press button "A", relay "1" will turn on. Press button "A" again, relay "1" will turn off.
  • Similarly, button "B" controls relay "2".

6.3 Latched Mode (Press 3 times)

Latched Mode requires a remote control with at least 3 buttons (A, B, C). Pressing one button activates its corresponding relay and deactivates any other active relays. A third button (C) can be used to turn off all relays.

  1. Setup: Press the learning button on the receiver 3 times. Wait 3 seconds.
  2. Press button "A" on the remote control 1 time.
  3. Press button "B" on the remote control 1 time. Pairing is successful.
  • Press button "A", relay "1" will turn on.
  • Press button "B", relay "2" will turn on, and simultaneously relay "1" will turn off.
  • (If using a 3-button remote) Press button "C", both relays "1" and "2" will turn off.

6.4 Mix Mode (Press 4 times)

Mix Mode combines Momentary and Toggle functionality for different channels.

  1. Setup: Press the learning button on the receiver 4 times. Wait 3 seconds.
  2. Press button "A" on the remote control 1 time.
  3. Press button "B" on the remote control 1 time. Pairing is successful.
  • Press and hold button "A", relay "1" will turn on. Release button "A", relay "1" will turn off (Momentary).
  • Press button "B", relay "2" will turn on. Press button "B" again, relay "2" will turn off (Toggle).

6.5 Motor Toggle Mode (Press 5 times)

Motor Toggle Mode is designed for motor control, where one button activates a relay and the other button activates the second relay while deactivating the first, and pressing the same button again turns off its relay.

  1. Setup: Press the learning button on the receiver 5 times. Wait 3 seconds.
  2. Press button "A" on the remote control 1 time.
  3. Press button "B" on the remote control 1 time. Pairing is successful.
  • Press button "A", relay "1" will turn on. Press button "B", relay "2" will turn on, and simultaneously relay "1" will turn off. Press button "B" again, relay "2" will turn off.
  • Alternatively: Press button "B", relay "2" will turn on. Press button "A", relay "1" will turn on, and simultaneously relay "2" will turn off. Press button "A" again, relay "1" will turn off.

7. Resetting the Receiver

To clear all paired remote controls and reset the receiver to its default state:

  1. Press the learning button on the receiver 8 times.
  2. All previously paired remote controls will no longer function with this receiver. You will need to re-pair them if desired.

8. Maintenance

  • Remote Control Battery: Replace the CR2032 battery in the remote control when its voltage is low to ensure strong signal transmission.
  • Antenna: Slightly stretch the antenna on the receiver for better signal reception.
  • Keep the device clean and free from dust and debris.

9. Troubleshooting

  • Device not responding: Ensure power is supplied correctly (AC 90-250V or USB 5V). Check if the remote control battery is low. Verify that the remote control is paired correctly to the receiver.
  • Only USB power works, AC power fails: Some users have reported issues with 230V AC power supply where only USB power works. If this occurs, double-check your AC wiring and ensure it matches the diagram. If the issue persists, contact technical support.
  • Remote control not working after mode change: Remember to reset the receiver (press learning button 8 times) before changing the operating mode of a remote control. After a reset, all remote controls must be re-paired.
  • Remote control not working for specific application (e.g., garage door): Ensure the wiring is correct for your specific application. Refer to the wiring diagrams and consult the video tutorial if needed.
  • Signal range issues: Ensure the receiver's antenna is slightly stretched for optimal reception. Avoid placing the receiver near large metal objects or other sources of RF interference.

10. User Tips

  • Latched Mode with 2-Button Remote: Even with a 2-button remote, the interlocked (latched) mode can be activated. To deactivate the ON relay, press buttons A and B simultaneously.
  • Wiring Complexity: The connection process can be intricate. It is highly recommended to watch the official video tutorial for visual guidance on wiring and mode setup.
  • Multi-language Support: The instruction manual may include multiple languages, such as Korean, which can be helpful for non-English speakers.

11. Warranty and Support

This product is manufactured by Huizhou Wenqiao Electronic Technology Co., Ltd. and holds CE, FCC, UK CA, and RoHS certifications, ensuring compliance with relevant safety and environmental standards.

Certifications including CE, FCC, UK CA, and RoHS logos.

Figure 8: Product Certifications

For technical assistance or inquiries, please contact:

  • WhatsApp: +86 135 0227 8583 / +86 158 7521 8992
  • Email: dieseelectronic@163.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.