Introduction
The SA6 is a portable spectrum analyzer and signal source designed for analyzing signals in the frequency range of 35 to 6200 MHz. It accurately determines the amplitude and frequency of spectral components, supporting various widely used technologies including Wi-Fi, 2G, 3G, 4G, LTE, CDMA, DCS, GSM, GPRS, and GLONASS.
A key feature is its integrated tracking generator, which allows for measuring the frequency response of passive or active devices such as filters or amplifiers. The accompanying software facilitates SWR (Standing Wave Ratio) and return loss measurements, though this requires an external directional coupler and calibration.
Designed for field use, the SA6 is rugged, lightweight, and energy-efficient. It is an ideal tool for service centers and maintenance teams to conduct on-site HF analysis for commissioning and repair tasks. It also serves as a valuable instrument for repair shops and radio enthusiasts.
Typical applications include: external antenna placement on base stations, quick RF environment analysis, verifying the correct operation of trunking cells and radio stations, and the repair and adjustment of repeaters, generators, and filters.
The unit can be controlled via its physical buttons, the integrated touch screen, or connected to a PC via a USB cable for real-time data display. Its metal casing, large screen, and precise touch interface enhance usability. The device can operate independently without a constant power connection, thanks to its internal battery.
The SA6 offers powerful capabilities, including measurements up to 6GHz, 2.4G/5.8G antenna analysis, and duplexer/filter measurements.
Setup
Package Contents
Upon unboxing, verify that all components are present:
- SA6 Handheld Digital Spectrum Analyzer and Signal Generator Unit
- USB Type-C Cable
- SMA Cables (2x)
- Stylus
- SMA Adapter
- HT004A Low Noise Amplifier (LNA) (if included in your package)
- HT03 Near Field Probe Set (if included in your package)
Video: Unboxing and overview of the SA6 and its accessories.

Image: Contents of the SA6 package, including the main unit and various accessories.
Initial Charging
Before first use, fully charge the SA6 unit using the provided USB Type-C cable and a compatible 5V power source. The battery typically takes approximately 5 hours to fully charge.
Connecting Accessories
- SMA Cables: Use the provided SMA cables to connect antennas, probes, or other RF components to the SA6's RF IN and RF Output ports.
- HT004A Low Noise Amplifier (LNA): This amplifier is used to boost weak signals. Connect it between the signal source (e.g., antenna, near field probe) and the SA6's RF IN port. Ensure the LNA is powered (5V 1A).

Image: Examples of devices that can be used with the HT004A Low Noise Amplifier.
- HT03 Near Field Probe: For measuring electromagnetic signals in close proximity. Connect the probe to the SA6, potentially via the HT004A LNA for improved sensitivity.

Image: Diagram illustrating the connection flow for near-field measurements: Product to be tested, Near field probe, Signal amplifier, and Spectrum analyzer.

Image: The SA6 unit connected to a larger spectrum analyzer, demonstrating its use in a measurement setup with the HT004A amplifier.
Operating Instructions
Powering On/Off
Press and hold the power button (located on the top of the unit, near the Type-C port) to turn the device on or off.

Image: Top and bottom views of the SA6 unit, showing the Type-C charging port and RF IN/OUT ports.
User Interface and Controls
The SA6 features a 3.2-inch color resistive touch screen and physical buttons for navigation and control. The buttons typically include MKR (Marker), MENU, FREQ (Frequency), AMPL (Amplitude), and directional arrows for adjustment, along with SPAN +/- for adjusting the frequency span.

Image: Front view of the SA6 main unit, showing the display screen and control buttons.
PC Connection
Connect the SA6 to a Windows-based PC using the provided USB cable. This allows for real-time display of measurement data on the PC screen and potentially more advanced analysis or control via dedicated software (refer to the electronic manual for software details).
Near Field Probe Usage
When using the HT03 Near Field Probe, ensure it is positioned very close to the measurement target to obtain accurate readings. It is crucial to keep your hands away from the probe's PCB board during operation to avoid interference. Also, minimize other electromagnetic sources in the vicinity that could cause interference.

Image: The Magnetic Field Probe set (9KHz-3GHz) including various probe types.

Image: A set of near-field probes, showing different sizes and designs for various measurement needs.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the device, especially the screen. Avoid abrasive cleaners or solvents.
- Storage: Store the SA6 in a dry, dust-free environment away from extreme temperatures and direct sunlight.
- Battery Care: To prolong battery life, avoid fully discharging the battery frequently. Charge the device regularly, especially if it will be stored for an extended period.
- Connections: Ensure all SMA connectors are clean and free from debris before making connections to prevent signal loss or damage.
Troubleshooting
- Device does not power on: Ensure the battery is sufficiently charged. Connect the device to a power source using the USB Type-C cable and try again.
- No signal displayed: Check all cable connections (SMA cables, probes, amplifiers) for proper seating. Verify that the signal source is active and within the SA6's frequency range. If using an LNA, ensure it is powered.
- Inaccurate readings: Ensure proper calibration procedures are followed, especially for SWR measurements. Check for external interference sources. Verify that the correct measurement parameters (frequency, span, attenuation) are set.
- PC connection issues: Ensure the USB cable is securely connected to both the SA6 and the PC. Try a different USB port or cable. If necessary, check for required drivers or software updates for PC connectivity (refer to the electronic manual for specific software requirements).
- Touch screen unresponsive: Use the provided stylus for precise input. If the screen remains unresponsive, try restarting the device.
Specifications
SA6 Handheld Digital Spectrum Analyzer and Signal Generator
| Feature | Specification |
|---|---|
| Display | 3.2-inch color resistive touch screen |
| Frequency Range (Display & Measured) | 35 - 6200 MHz |
| Dynamic Range (35-3000 MHz) | 75 dB |
| Dynamic Range (3000-4500 MHz) | 70 dB |
| Maximum Span | 6165 MHz |
| Bandwidth | 200 kHz (fixed) |
| Scanning Speed (>100 MHz) | 700 MHz/sec |
| Scanning Speed (100 MHz) | <0.25 sec |
| Noise Floor (up to 3000 MHz) | <-90 dBm |
| Noise Floor (3000-4500 MHz) | <-85 dBm |
| Noise Floor (4500-6200 MHz) | <-80 dBm |
| Wave Impedance | 50 ohms |
| VSWR (over operating frequency range) | <1.5 |
| Internal Attenuator | 0-30 dB |
| Attenuation Error (up to 10 dB) | 2 dB |
| Attenuation Error (10-20 dB) | 5 dB |
| Attenuation Error (20-30 dB) | 8 dB |
| Tracking Generator Output Power | -15 to -25 dBm |
| Accuracy in Dynamic Range | 2.0 dB |
| Maximum Input Power (0 dB attenuator) | 10 dBm |
| Maximum Input Power (>20 dB attenuation) | +20 dBm |
| Maximum Input Measurement Signal | +10 dBm |
| Maximum Input DC Voltage | 25 volts |
| Maximum Current Consumption (battery) | 450 mA |
| Maximum Current Consumption (USB, charging) | 500 mA |
| Battery Capacity | 2500 mA |
| Battery Life | 3 hours |
| Battery Charging Time | ~5 hours |
| Dimensions | 155 x 81 x 27 mm |
| Weight | 0.49 kg |

Image: Dimensions of the SA6 unit (135mm x 75mm x 23mm).

Image: Size comparison of the SA6 unit with a smartphone, highlighting its portability.
HT004A Low Noise Amplifier (LNA)
| Feature | Specification |
|---|---|
| Item Type | Low Noise Amplifier |
| Model | HT004A |
| Material | Metal |
| Frequency Range | 0.1 MHz - 6 GHz |
| Connector | SMA female |
| Gain | 30 dB |
| Input and Output Impedance | 50 Ω |
| Input Voltage | 5V 70mA |
| Battery Type | Internal Battery |
| Product Size | 68 x 40 x 15 mm (2.7 x 1.6 x 0.6 inch) |

Image: Dimensions of the HT004A Low Noise Amplifier.
HT03 Near Field Probe
| Feature | Specification |
|---|---|
| Model | HT03 Near Field Probe |
| Operating Frequency | 9 KHz - 3 GHz |
| Connector | SMA female |

Image: Dimensions of the various near-field probes in the HT03 set.
User Tips
- Probe Handling: When using the HT03 near-field probe, always keep your hands away from the PCB board to prevent interference and ensure accurate measurements.
- Optimal Measurement: For best results with near-field probes, maintain a very close distance between the probe and the object under test.
- Minimize Interference: During any measurement, try to eliminate or minimize other potential electromagnetic interference sources in the testing environment.
- Software Updates: Check the manufacturer's website or the provided electronic manual for any available software updates for PC connectivity or device firmware to ensure optimal performance and access to new features.
Warranty and Support
For warranty information, technical support, or to obtain a detailed electronic manual, please refer to the documentation provided with your purchase or contact the seller directly. Keep your purchase records for any warranty claims.