1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Aerlang A11 electric scooter dashboard display. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. This dashboard display is specifically designed for compatibility with the Aerlang A11 electric scooter.
2. Package Contents
- Aerlang A11 Dashboard Display Unit
- Integrated Connecting Cable
3. Product Overview
The Aerlang A11 dashboard display serves as the central interface for monitoring your scooter's performance and status. It features a clear digital readout, battery indicator, and an integrated throttle for intuitive control.
Figure 3.1: Aerlang A11 electric scooter with the dashboard display unit highlighted.
3.1 Display Features
Figure 3.2: Front view of the Aerlang A11 dashboard display.
- Digital Readout: Displays current speed (e.g., '88'), and potentially other numerical information.
- Battery Indicator: Shows the remaining battery charge level.
- Lock Icon: Indicates if the scooter is locked.
- Speed Unit: Displays 'km/h' or 'mph' for speed measurement.
- Power Button: Used for turning the display on/off and potentially cycling through modes.
3.2 Integrated Controls and Connections
Figure 3.3: Side view showing the integrated throttle lever.
Figure 3.4: Bottom view showing the connecting cable.
- Throttle Lever: Located on the side, this lever controls acceleration.
- Connecting Cable: A dedicated cable for connecting the display to the scooter's main control system.
- Mounting Bracket: Designed for secure attachment to the scooter's handlebar.
4. Installation/Setup
Safety First: Before beginning installation, ensure your electric scooter is powered off and disconnected from any power source. Wear appropriate safety gear if necessary.
- Remove Old Display (if applicable): Carefully disconnect the existing dashboard display from your scooter. Note the cable routing and connection points.
- Mount New Display: Position the new Aerlang A11 dashboard display on the handlebar in a comfortable and visible location. Use the integrated mounting bracket to secure it firmly. Ensure it does not interfere with braking or steering.
- Connect Cable: Locate the corresponding port on your Aerlang A11 scooter's wiring harness. Connect the display's integrated cable securely to this port. Ensure the connection is snug to prevent accidental disconnection during operation.
- Test Functionality: Once installed, power on your scooter. The dashboard display should illuminate and show information. Test the throttle response and ensure all indicators (battery, speed) are functioning correctly.
Figure 4.1: Top view showing the mounting bracket.
5. Operating Instructions
- Power On/Off: Press and hold the power button (refer to Figure 3.2) for a few seconds to turn the display on or off.
- Speed Control: Use the integrated throttle lever (refer to Figure 3.3) to control the scooter's acceleration. Push the lever to increase speed.
- Monitoring Display: While riding, the display will show your current speed, battery level, and other relevant status indicators.
- Changing Speed Units (if applicable): A short press of the power button might cycle through different display modes or allow you to switch between km/h and mph. Refer to your scooter's main manual for specific instructions on display settings.
6. Maintenance
- Cleaning: Use a soft, dry cloth to wipe the display screen. Avoid using abrasive cleaners or solvents that could damage the screen or casing.
- Water Exposure: While the display is designed for outdoor use, avoid prolonged exposure to heavy rain or submerging the unit in water. Ensure the cable connection remains dry.
- Connection Check: Periodically check that the connecting cable is securely attached to prevent intermittent issues.
- Storage: If storing the scooter for an extended period, ensure the display is clean and dry.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display does not turn on. | Scooter not powered on; loose cable connection; scooter battery depleted. | Ensure scooter is powered on. Check cable connection. Charge scooter battery. |
| Incorrect speed reading. | Sensor issue; display settings incorrect. | Consult your scooter's main manual for sensor troubleshooting. Check display settings for unit (km/h vs mph). |
| Throttle not responding. | Loose cable connection; internal fault. | Check cable connection. If problem persists, contact support. |
8. Specifications
- Compatibility: Aerlang A11 Electric Scooter
- Dimensions (Approx.):
- Length: 13 cm
- Width: 8 cm
- Height: 9 cm
- Weight (Approx.): 0.3 kg
- Origin: Mainland China
- High-concerned chemical: None
9. User Tips
- Always ensure the display is securely mounted to prevent vibration damage during rides.
- Familiarize yourself with the display's indicators before riding to quickly understand your scooter's status.
- If you experience any unusual behavior, always perform a basic connection check before seeking further assistance.
10. Warranty and Support
For any warranty claims, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.