Estardyn 0.96 inch OLED module

Contents

Estardyn 0.96 Inch OLED Display Module User Manual

Model: 0.96 inch OLED module

1. Introduction

This manual provides essential information for the setup, operation, and maintenance of your Estardyn 0.96 Inch OLED Display Module. This compact display features a 128x64 pixel resolution and utilizes IIC (I2C) serial communication, making it highly compatible with various microcontrollers such as Arduino, 51 Series, MSP430 Series, STM32/2, and CSR ICs.

The module is designed for ultra-low power consumption (approximately 0.08W when fully lit) and offers adjustable high brightness and contrast. It comes with an embedded driver/controller, simplifying integration into your projects.

Various 0.96 inch OLED display modules showing different color options and example graphics.

Figure 1: Estardyn 0.96 Inch OLED Display Modules in White, Blue, and Blue&Yellow variants.

2. Specifications

FeatureDescription
Display Mode128 x 64 pixels
Resolution128 x 64
TypeGraphic OLED
Model Number0.96 inch OLED module
Interface TypeIIC (I2C)
Pin DefinitionGND, VCC, SCL, SDA (4 pins)
Operating Voltage3V ~ 5V DC
Working Temperature-30 °C ~ 70 °C
Drive Duty1/64 Duty
Panel Dimensions (approx)26.70 x 19.26 x 1.85 mm (1.03 x 0.76 x 0.07 inch)
Active Area (approx)21.74 x 11.2 mm (0.86 x 0.44 inch)
Driver ICSSD1306 (Blue board), SSD1315 (Black board)
Technical drawing of the SSD1306 OLED module with dimensions and active area indicated.

Figure 2: SSD1306 Module Dimensions and Active Area.

Technical drawing of the SSD1315 OLED module with dimensions and active area indicated.

Figure 3: SSD1315 Module Dimensions and Active Area.

3. Setup

3.1 Pinout

The module features a 4-pin interface for IIC communication:

  • GND: Ground connection.
  • VCC: Power supply (3V to 5V DC).
  • SCL: Serial Clock Line for IIC communication.
  • SDA: Serial Data Line for IIC communication.

3.2 Wiring to a Microcontroller (e.g., Arduino)

Connect the OLED module to your microcontroller as follows:

  • GND on OLED to GND on Arduino
  • VCC on OLED to 3.3V or 5V on Arduino (depending on your Arduino model and desired voltage)
  • SCL on OLED to SCL (A5 on Uno, D21 on Mega) on Arduino
  • SDA on OLED to SDA (A4 on Uno, D20 on Mega) on Arduino

3.3 IIC Address Selection

Some modules, particularly the SSD1306 (blue board), may have jumpers for IIC address selection. The common addresses are 0x3C (or 0x78) and 0x3D (or 0x7A). Refer to the back of your module for specific jumper configurations if needed. Typically, the default address is 0x3C.

Back of the blue OLED module board showing IIC address selection jumpers labeled 0x78 and 0x7A.

Figure 4: Back of the SSD1306 (Blue Board) with IIC Address Selection.

Back of the black OLED module board, typically using SSD1315 driver.

Figure 5: Back of the SSD1315 (Black Board).

4. Operating Instructions

To operate the OLED display, you will typically use a compatible library for your chosen microcontroller platform. For Arduino, popular libraries include:

  • Adafruit SSD1306 Library: A widely used library that supports both SSD1306 and SSD1315 drivers.
  • Adafruit GFX Library: A core graphics library required by the SSD1306 library for drawing shapes, text, and bitmaps.

4.1 Basic Programming Steps (Arduino Example)

  1. Install Libraries: Open your Arduino IDE, go to Sketch > Include Library > Manage Libraries, and search for 'Adafruit SSD1306' and 'Adafruit GFX'. Install both.
  2. Include Headers: In your sketch, include the necessary headers:#include <Wire.h> (for I2C communication)#include <Adafruit_GFX.h>#include <Adafruit_SSD1306.h>
  3. Define Display Parameters: Define the screen width, height, and I2C address. For example:#define SCREEN_WIDTH 128#define SCREEN_HEIGHT 64#define OLED_RESET -1 (or the reset pin if you have one)Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);
  4. Initialize Display: In your setup() function, initialize the display and check for successful connection:if(!display.begin(SSD1306_SWITCHCAPVCC, 0x3C)) { (0x3C is a common I2C address) Serial.println(F("SSD1306 allocation failed")); for(;;);}display.display(); (Clears the buffer and shows the Adafruit logo)delay(2000);display.clearDisplay();
  5. Display Content: Use functions like display.setTextSize(), display.setTextColor(), display.setCursor(), display.print(), display.drawPixel(), display.drawRect(), etc., to draw on the buffer. After drawing, call display.display() to update the physical screen.

Refer to the example sketches provided with the Adafruit SSD1306 library for more detailed usage and advanced features.

5. Maintenance

The Estardyn OLED display module is a robust electronic component, but proper care ensures its longevity:

  • Handling: Always handle the module by its edges to avoid touching the display surface or delicate components.
  • Cleaning: If necessary, gently wipe the display surface with a soft, dry, lint-free cloth. Avoid using harsh chemicals or abrasive materials.
  • Environmental Conditions: Operate and store the module within the specified working temperature range (-30 °C to 70 °C). Avoid exposure to extreme humidity, direct sunlight, or corrosive environments.
  • Static Discharge: Take precautions against electrostatic discharge (ESD) when handling the module, as static electricity can damage electronic components.
  • Power Supply: Ensure the power supply voltage is within the specified 3V to 5V DC range. Incorrect voltage can damage the module.

6. Troubleshooting

If you encounter issues with your OLED display module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Check Wiring: Verify all 4 pins (GND, VCC, SCL, SDA) are correctly connected to your microcontroller.
    • Check Power: Ensure VCC is receiving the correct voltage (3V-5V DC) and GND is properly connected.
    • Check IIC Address: Confirm the IIC address used in your code matches the module's address (commonly 0x3C or 0x3D). Some modules have jumpers to change this.
    • Code Initialization: Ensure the display initialization code (e.g., display.begin()) is called correctly and returns true.
  • Garbled/Incorrect Display:
    • Driver IC: Ensure your code is configured for the correct driver IC (SSD1306 or SSD1315). While many libraries handle both, explicit configuration might be needed.
    • Library Issues: Make sure you are using a compatible and up-to-date library.
    • Buffer Updates: Remember to call display.display() after drawing to the buffer to update the physical screen.
  • Communication Errors:
    • I2C Scanner: Use an I2C scanner sketch (available online) to detect if your microcontroller can find the OLED module on the I2C bus and identify its address.
    • Pull-up Resistors: While most microcontrollers have internal pull-ups, external 4.7kΩ pull-up resistors on SCL and SDA lines can sometimes resolve communication issues, especially with longer wires.

7. User Tips

  • Power Consumption: OLED displays consume power based on the number of lit pixels. To conserve power, consider displaying less information or using darker themes when possible.
  • Burn-in Prevention: While OLEDs are less prone to burn-in than older display technologies, displaying static images for extremely long periods can still cause it. Consider implementing screen savers or periodically shifting content if your application requires continuous display of static elements.
  • Code Examples: Always start with the basic example sketches provided by the display library to verify hardware functionality before integrating into complex projects.

8. Support

For further assistance or technical inquiries, please contact your retailer or the manufacturer directly. Provide your product model number and a detailed description of the issue for efficient support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.