SHEHDS 36x18W LED Zoom Wash Moving Head Lighting User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your SHEHDS 36x18W LED Zoom Wash Moving Head Lighting fixture. Please read these instructions thoroughly before installation, operation, or maintenance. Keep this manual for future reference.

2. Safety Information

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.

• Ensure the fixture is properly grounded.
• Do not operate the fixture if the power cord is damaged.
• Disconnect from power before servicing or cleaning.
• Avoid direct eye exposure to the light source.
• Ensure adequate ventilation around the fixture.
• Installation should be performed by qualified personnel.

3. Package Contents

Verify that all components are present upon unpacking:

• LED Zoom Moving Head Light (x1)
• User Manual (x1)
• 1.2m Power Cable (x1)
• 2m DMX Cable (x1)
• Lock (x1)

4. Setup

4.1 Initial Inspection

Before connecting the fixture, carefully inspect it for any damage that may have occurred during shipping. If any damage is found, do not operate the unit and contact your supplier.

4.2 Mounting

The fixture can be mounted in various positions (e.g., truss, floor). Ensure the mounting surface or structure can support the weight of the fixture (Net weight: 7.55 kg / 16.64 lbs). Use appropriate clamps and safety cables. The fixture includes a lock for secure mounting.

4.3 Connections

The rear panel of the fixture provides all necessary connections for power and DMX control.

1. Power Connection: Connect the provided 1.2m power cable to the POWER IN socket. The fixture supports AC100V-240V, 50/60Hz. Use the POWER OUT socket to daisy-chain power to other compatible fixtures if needed.
2. DMX Connection: Connect a DMX controller to the DMX IN socket using the provided 2m DMX cable. Use the DMX OUT socket to daisy-chain DMX signal to other fixtures.
3. Power On/Off: Use the ON/OFF switch located on the rear panel to power the unit.

5. Operating Instructions

5.1 Control Panel

The fixture features an LCD display and menu keys for configuration and manual control.

Use the menu keys (Up, Down, Left, Right, Enter) to navigate through the settings and adjust parameters. The LCD display provides real-time feedback on the fixture's status and current settings.

5.2 DMX Control

The fixture operates using the international standard DMX512 protocol. It supports 12 or 18 channel modes, selectable via the control panel. Refer to the DMX chart (usually found in the full manual or product specifications) for detailed channel assignments and functions.

5.3 Key Features and Effects

The SHEHDS 36x18W LED Zoom Wash Moving Head Light offers a variety of effects for dynamic lighting displays:

• Light Source: RGBWA UV 6in1 mix color for a wide spectrum of hues.
• Dimmer: 0-100% linear adjustment for smooth intensity control.
• Strobe: Adjustable speed strobe effect (0-20Hz).
• Zoom: Linear adjustment zoom beam with an angle of 15-45 degrees.
• Movement: Pan: 540°, Tilt: 185° for broad coverage.
• Beam Effects: Capable of producing multiple beam effects and color changes.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your fixture.

• Cleaning: Clean the lens and housing regularly with a soft, lint-free cloth. Do not use abrasive cleaners.
• Fan Cleaning: Periodically check and clean the cooling fan to prevent dust buildup, which can impair cooling efficiency.

• Fuse Replacement: If the fixture does not power on, check the fuse located on the rear panel (refer to Figure 4.2). Replace with a fuse of the same type and rating.
• Internal Components: The internal components, including the mainboard, motor, and power supply, are designed for durability. Any internal servicing should be performed by qualified technicians.

7. Troubleshooting

If you encounter issues with your fixture, refer to the following common problems and solutions:

• No Power:
  1. Check if the power cable is securely connected to both the fixture and the power outlet.
  2. Verify the power outlet is functional.
  3. Inspect the fuse on the rear panel and replace if blown (refer to Section 6, Maintenance).
  4. Ensure the ON/OFF switch is in the 'ON' position.
• No Light Output:
  1. Confirm the fixture is receiving power.
  2. Check dimmer settings on the control panel or DMX controller; ensure intensity is not set to 0.
  3. Verify DMX signal is present and the fixture's DMX address is correctly set.
• No DMX Control:
  1. Ensure DMX cables are correctly connected (DMX IN/OUT).
  2. Check the DMX address of the fixture and ensure it matches your DMX controller settings.
  3. Verify the DMX controller is functioning correctly.
  4. Try a different DMX cable.
• Fixture Not Moving (Pan/Tilt):
  1. Check for any physical obstructions.
  2. Ensure DMX control channels for Pan/Tilt are active and sending commands.
  3. Reset the fixture by powering it off and on.

8. Specifications

9. User Tips

• For optimal light coverage, consider the LUX-Distance chart (Figure 5.5) when positioning multiple fixtures.
• Experiment with different DMX channel modes (12 or 18) to find the balance between control granularity and DMX channel consumption for your setup.
• Utilize the linear zoom feature to adjust beam spread from a tight spot to a wide wash, adapting to different event requirements.
• Regularly check the cooling fan for obstructions to ensure efficient heat dissipation, especially during long periods of operation.

10. Frequently Asked Questions (FAQ)

Q: Is the power cable included with the fixture?

A: Yes, a 1.2m power cable is included in the package. A 2m DMX cable is also provided.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.