Douk Audio BSA-600

Contents

Nobsound BSA-600 Bass Shaker Amplifier User Manual

Model: BSA-600

Brand: Douk Audio

1. Introduction

The Nobsound BSA-600 is a powerful 230W Bridge Stereo/Mono Bass Shaker Amplifier designed to enhance your sensory experience in home theater and gaming setups. It provides a controlled signal to bass shakers, subwoofers, and low-frequency transducers, allowing you to feel extremely low-frequency sounds that are often too low to hear. This adds a new dimension of immersion, from explosions in movies to the subtle rumble of road surfaces in racing simulators.

This manual provides detailed instructions for setting up, operating, and maintaining your BSA-600 amplifier to ensure optimal performance and longevity.

2. Package Contents

Please check the package contents upon unboxing:

  • 1 × BSA-600 Amplifier
  • 1 × Power Cord
  • 1 × Wired Remote (5m / 16.4 ft)
  • 1 × Type-C Cable (for remote)
  • 1 Set × Brackets
  • 2 × Double-sided Adhesive
  • 1 × User Manual
Packing list and dimensions of the BSA-600 amplifier and included accessories.
Figure 2.1: Package Contents and Dimensions. The amplifier measures 242mm (W) x 214mm (D) x 65mm (H).

3. Setup

3.1 Physical Placement

The BSA-600 amplifier is designed for versatile installation. You can place it on a shelf or use the included brackets and double-sided adhesive for custom mounting options, such as under a couch, gaming chair, or equipment rack, to save space.

Flexible installation options for the BSA-600 amplifier, including under a couch or gaming chair.
Figure 3.1: Example of flexible installation under furniture.

3.2 Connections

Refer to the rear panel diagram for proper wiring. Ensure all connections are secure before powering on the device.

Rear panel connections and wiring diagram for the BSA-600 amplifier.
Figure 3.2: Rear Panel Connections Diagram.
  1. Power Connection: Connect the provided power cord to the AC 100V-240V IN port on the rear panel and then to a suitable power outlet.
  2. Audio Input (RCA): Connect your audio source (e.g., TV, TV set-top box, laptop, computer, phone, tablet PC) to the RCA input ports. The RCA input can accept either a full-frequency signal or a low-frequency signal.
  3. Speaker Output (Banana Jacks): Connect your bass shakers or passive subwoofers to the banana speaker jacks. These jacks only output low frequency and are designed to drive subwoofers or bass shakers; they cannot power full-frequency speakers.
  4. Mono Output: For mono output, connect your bass shakers or passive subwoofers to the dedicated Mono output terminals.
  5. RCA Output: The RCA output ports allow you to daisy chain multiple BSA-600 units for larger installations or multi-room setups. The RCA output signal will be the same as the RCA input signal, without any additional amplification.
  6. 5V Output Charging Port: An external USB 5V/1A output is available to provide power for other devices, helping to reduce cable clutter.
  7. Wired Remote: Connect the wired remote control to the 'REMOTE' port on the front panel using the Type-C cable.

4. Operation

Front panel controls and indicators of the BSA-600 amplifier.
Figure 4.1: Front Panel Controls and Indicators.

4.1 Power On/Off

  1. Ensure the power cord is connected and the main power switch on the rear panel is in the 'ON' position.
  2. To Turn On: Short press the VOL knob on the front panel. The power indicator will be steady on, and the display screen will show the volume value.
  3. To Turn Off: Long press the VOL knob.

4.2 Front Panel Controls

  • Mono/Stereo Select Switch: Toggle between Mono and Stereo output modes.
  • Auto Standby Switch: Set to 'ON' for auto standby mode. The amplifier will enter standby after 10 minutes if no signal input is detected. It will automatically power on when a signal (≥15mV at 1KHz) is detected.
  • VOL (Volume) Knob: Rotate to adjust the output volume. Short press to mute/unmute.
  • FREQ (Cutoff Frequency) Knob: Adjusts the cutoff frequency from 50-200Hz to find the desired crossover point for your low-end audio.
  • BAL (Balance) Knob: Adjusts the balance of the low-end output in your audio system.

4.3 Wired Remote Control

The wired remote control provides convenient access to volume adjustment, mute, and amplifier power on/off, especially when the amplifier is installed in hard-to-reach locations.

Wired remote control for the BSA-600 amplifier and its use in a home theater setting.
Figure 4.2: Wired Remote Control in use.
  • Short Press: Turn on / Mute
  • Long Press: Turn off
  • Rotate: Adjust the volume

Video 4.1: Demonstration of the BSA-600 amplifier's bass shaker effect, showing vibrations with a cup of water.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the amplifier's exterior. Avoid using liquid cleaners or solvents.
  • Ventilation: Ensure adequate ventilation around the amplifier to prevent overheating. Do not block the ventilation holes.
  • Storage: When not in use for extended periods, store the amplifier in a cool, dry place away from direct sunlight and extreme temperatures.
  • Cable Management: Keep cables organized and free from kinks or excessive tension to prevent damage.

6. Troubleshooting

  • Power Indicator Flashing: If the power indicator is flashing after pressing the power switch on the back panel, short press the VOL knob on the front panel to turn it on. The power indicator should then become steady, and the display screen will show the volume value.
  • No Sound/Low Bass:
    • Check all audio input and output connections.
    • Ensure the volume is turned up on both the amplifier and your audio source.
    • Adjust the FREQ (cutoff frequency) and BAL (balance) knobs to optimize the low-end output.
    • Verify that your bass shakers or subwoofers are correctly connected to the low-frequency output terminals.
  • Overheat Protection (Display 'OL'): If the display shows 'OL', it indicates the amplifier has overheated. The amplifier will automatically relieve the overheat condition and recover after approximately 10 seconds. Ensure proper ventilation around the unit.
  • Overcurrent Protection (Display 'OC'): If the display shows 'OC', it indicates an overcurrent condition. The amplifier will automatically relieve the overcurrent and recover after approximately 10 seconds. Check speaker impedance and wiring for any shorts or incorrect connections.
  • Auto Standby Not Working: Ensure the 'AUTO' switch on the front panel is set to 'ON'. The amplifier requires a signal of at least 15mV at 1KHz to power on from standby.
  • RCA Output Signal: Note that the RCA output signal is a parallel pass-through of the RCA input signal and does not undergo any amplification by the BSA-600.

7. Specifications

FeatureSpecification
BrandDouk Audio
ModelBSA-600
Audio InputStereo RCA
Audio OutputBanana Speaker Jacks / Stereo RCA
Max. Output Power (Stereo)115W × 2 (4Ω)
Max. Output Power (Mono)230W × 1 (2Ω)
Matched Speaker Impedance2-8Ω
Range of Cutoff Frequency50-200Hz
Input Sensitivity0.22mV@50Hz
Auto Standby Time (no signal)After 10 minutes
Lowest Drive Level to Power On≥15mV at 1KHz
Gain40dB
Distortion0.1%
S/N Ratio≥105dB
USB Output VoltageDC 5V/1A
Working VoltageAC 100-240V
External Wired RemoteSupported (5m / 16.4 ft cable)
Standby Power Consumption0.5W
Net Weight2.34kg / 5.16lb
Dimensions (W×D×H)242 × 214 × 65mm / 9.53 × 8.43 × 2.56in
CertificationCE

8. User Tips

  • For optimal tactile feedback, experiment with the placement of bass shakers on your furniture. Different positions can yield varying levels of immersion.
  • Adjust the cutoff frequency (FREQ knob) carefully to blend the bass shaker output seamlessly with your main audio system. Start with lower frequencies and gradually increase until you find a natural extension of your audio.
  • The balance knob (BAL) can be used to fine-tune the intensity of the low-frequency effects, allowing you to customize the experience to your preference.
  • When daisy-chaining multiple units, ensure consistent settings across all amplifiers for a cohesive multi-zone experience.
  • Utilize the 5V USB output to power small accessories like LED strips or other low-power devices, helping to keep your setup tidy.

9. Warranty and Support

For any questions, technical support, or warranty inquiries regarding your Nobsound BSA-600 amplifier, please contact Douk Audio customer service or visit their official website. Keep your purchase receipt as proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.