1. Introduction
This manual provides detailed instructions for the installation, setup, and operation of the Diatone MAMBA F722 APP MK4 Flight Controller Stack. This high-performance stack is designed for FPV (First Person View) drones, integrating a powerful F7 flight controller with a 4-in-1 BLHeli32 ESC, offering robust control and power delivery for demanding flight applications. It supports various current ratings (45A, 55A, 65A) and features a built-in WiFi module for convenient wireless configuration.
Video: Overview of the Diatone MAMBA F722 APP MK4 Flight Controller Stack.
2. Safety Information
Please read and understand all safety warnings before using this product. Improper use can lead to serious injury or damage to equipment.
- Always disconnect the battery before performing any maintenance or installation.
- Ensure correct polarity when connecting power. Incorrect wiring can permanently damage the device.
- Soldering should be performed by experienced individuals. Use appropriate safety gear.
- Keep the flight controller and ESC away from water, moisture, and extreme temperatures.
- Verify all connections and settings in Betaflight or other configuration software before powering up your drone.
- Always remove propellers when testing motors or making changes to the flight controller settings.
- This product is intended for users aged 14 and above.
3. Package Contents
Verify that all items listed below are included in your package:
Image: Detailed list of accessories included in the package.
| Accessory | Quantity |
|---|---|
| Packaging Box | 1 |
| MK4 F722 APP FC | 1 |
| M3 silicone damping | 5 |
| M3 ESC isolation column | 5 |
| 8 Pin single-ended cable for flight control | 1 |
| 8 Pin cable | 2 |
| 6 Pin Airunit Cable | 1 |
| MAMBA Brand Cards | 1 |
| After-sales support card | 1 |
4. Specifications
Detailed specifications for the MAMBA MK4 F722 APP Flight Controller and associated ESCs:
Image: Technical parameters for the MAMBA MK4 F722 APP Flight Controller.
4.1 Flight Controller (MAMBA MK4 F722 APP)
- MCU: STM32F722
- Frequency: 216MHz
- Gyro: Version A: BMI270, Version B: ICM42688P (Note: B-FC Gyro is ICM42688P, A-FC Gyro is MPU6000)
- OSD: AT7456E
- Blackbox: 16M Memory
- Uarts: 6 Set
- Receiver: TBS/SBUS/IBUS/DSM
- I2C: Yes
- F.Port: Yes
- Buzzer Pad: Yes
- CURR Pad: Yes
- ESC Signal: 8 Set
- BEC 3.3V: 0.5A
- BEC 5V: 3A
- BEC 9V: 3A
- MB LED: Yes
- BF LED: Yes
- AIR UNIT Port: Yes
- VTX Switch: Yes
- BEC Protection: Yes
- Receiver Protection: Yes
- TVS Protection: Yes
- Input: 6S Lipo
- Software: Betaflight
- Mounting: 30.5x30.5mm/M3
- Size: 38.0x40.5x8mm
- Weight: 10g
4.2 Electronic Speed Controller (ESC) Options
Image: Specifications for the F45, F55, and F65 128K ESCs, including capacitor connection details.
| Parameter | F45_128K ESC | F55_128K ESC | F65_128K ESC |
|---|---|---|---|
| Current | 45A | 55A | 65A |
| Peak Current | 55A | 65A | 75A |
| Input | 3-6S Lipo | 3-6S Lipo | 3-6S Lipo |
| BEC | No | No | No |
| PWM | 24-128K | 24-128K | 24-128K |
| Mounting | 30.5x30.5mm/M3 | 30.5x30.5mm/M3 | 30.5x30.5mm/M3 |
| Weight | 15g | 15g | 15g |
5. Setup and Installation
5.1 Physical Installation
The MAMBA MK4 F722 APP Flight Controller Stack features a 30.5x30.5mm mounting pattern with M3 holes. Use the provided M3 silicone damping and ESC isolation columns for secure and vibration-dampened mounting. The stack is designed with large soldering pads for easier connections.
Image: Front view of the MAMBA MK4 F722 APP Flight Controller Stack, highlighting the large soldering pads.
Image: Close-up of the Type-C interface and the DJI 6P SH1.0 connector for Air Unit connection.
5.2 Wiring Diagram
Refer to the detailed wiring diagram for connecting your flight controller stack to other components such as motors, receiver, VTX, camera, GPS, and Air Unit. Ensure all connections are secure and correctly oriented.
Image: Detailed wiring diagram showing connections for motors, receiver, VTX, camera, GPS, and DJI Air Unit. Note the VTX power switch settings and voltage warnings.
Important Notes from Wiring Diagram:
- VTX Power Switch: The VTX power channel (USER1) can be configured to switch the VTX power on or off after setting the channel.
- VTX Voltage Warning: Please check the voltage before wiring! (Default 9V voltage).
- DJI Air Unit Connection: The stack supports O3 fast connection. Use the dedicated 6-pin Airunit cable for simplified connection.
- Capacitor Connection: A capacitor is requested when using a 6S battery. Refer to the diagram for correct connection.
5.3 Mobile WiFi Configuration
The MAMBA F722 APP MK4 features an integrated WiFi module for wireless configuration via a mobile app. Follow these steps to connect and configure your flight controller:
Image: Step-by-step tutorial for connecting the flight controller to the Speedbee mobile app via WiFi.
- Ensure that the port UART4 MSP setting is on (factory default on).
- Open the Speedbee mobile app and select your model from "WIFI devices". If your current model is not in the list, simply select any of the listed models.
- Connect to the WiFi network named "Mamba Stack". Return to the Speedbee APP; the connection should be completed.
Attention:
- If you don't see your FC in the connection list, please wait for the official Speedbee update.
- If you can't connect to WiFi and get a prompt like "No data reading", "Mamba not responding", please check the settings in Port UART4. Keep the Speedbee APP to the latest version. Restart the device and the Speedbee app.
6. Operation
Once installed and configured, the MAMBA F722 APP MK4 Flight Controller Stack operates using Betaflight firmware. You can further fine-tune your drone's flight characteristics, motor outputs, and other settings using the Betaflight Configurator software on your PC or the Speedbee mobile app via WiFi.
- Betaflight Configuration: Connect the flight controller to your computer via the USB Type-C port. Open Betaflight Configurator to access all settings, flash firmware, and calibrate sensors.
- Wireless Configuration: Use the Speedbee mobile app as described in Section 5.3 for convenient adjustments in the field.
- Flight Modes: Configure desired flight modes (e.g., Acro, Angle, Horizon) in Betaflight and assign them to your radio switches.
- OSD (On-Screen Display): Customize the OSD to display critical flight information such as battery voltage, current, flight time, and RSSI.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your flight controller stack.
- Cleaning: Periodically clean the boards with a soft brush and isopropyl alcohol to remove dust and debris. Ensure no conductive materials bridge components.
- Inspection: Regularly inspect solder joints for cracks or cold joints. Check wires for fraying or damage.
- Firmware Updates: Keep your Betaflight firmware and BLHeli32 ESC firmware updated to benefit from performance improvements and bug fixes. Always back up your configuration before updating.
- Environmental Protection: Avoid exposing the stack to excessive vibrations, moisture, or extreme temperatures. Consider conformal coating for added protection in wet environments.
8. Troubleshooting
If you encounter issues with your MAMBA F722 APP MK4 Flight Controller Stack, consider the following troubleshooting steps:
- No Power: Check battery connection, main power lead soldering, and ensure no short circuits. Verify BEC outputs (3.3V, 5V, 9V) with a multimeter.
- No Connection to Betaflight/Speedbee App:
- Ensure correct USB drivers are installed for Betaflight.
- For WiFi connection, verify UART4 MSP is enabled and the Speedbee app is up-to-date. Try restarting the device and app.
- Check USB cable integrity.
- Motors Not Spinning/Incorrectly:
- Verify motor wiring to the ESC.
- Check motor direction and ESC protocol settings in Betaflight.
- Calibrate ESCs if necessary.
- Ensure propellers are removed during testing.
- Unstable Flight:
- Check for excessive vibrations; ensure FC is soft-mounted correctly.
- Verify PID tuning settings in Betaflight.
- Ensure gyroscope is correctly calibrated and functioning.
- VTX Issues: Check VTX power settings and ensure the VTX switch is configured correctly if used. Verify antenna connection.
9. User Tips
- Gyroscope Version: When selecting your flight controller, note that the B-FC version uses the ICM42688P gyroscope, while the A-FC version uses the MPU6000. Consider which gyroscope is better suited for your specific build and flight preferences.
- Firmware Compatibility: Always ensure that the Betaflight firmware version you are using is compatible with your specific MAMBA F722 MK4 hardware revision. Check official Diatone resources for recommended firmware targets.
- Soldering Best Practices: Utilize flux and a temperature-controlled soldering iron for clean and reliable solder joints, especially on the smaller pads.
10. Warranty and Support
For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty-related inquiries.
Manufacturer: Diatone
Brand: U-Angel-1988