Introduction
Thank you for choosing the TYT MD-8500 Repeater Base Digital Signal DMR & Analog TDMA Radio Station. This device is designed to provide reliable and efficient two-way voice communication, featuring advanced Time Division Multiple Access (TDMA) technology for improved spectrum utilization and increased user capacity. It supports both digital and analog modes, ensuring versatile operation.
The MD-8500 incorporates safe digital encryption technology with 128-bit encryption to protect your communications. Its robust design includes an original heat pipe radiator and a temperature-controlled cooling fan for excellent heat dissipation, ensuring stable performance even under full power conditions. The repeater supports dual-slot digital voice streams and offers a mixed working mode for analog and digital signals.
Safety and Warnings
Please read all safety information carefully before using the product to prevent injury or damage.
General Cautions
- Do not operate the transceiver in flammable, explosive, or other forbidden places such as petrol stations, gas stations, hospitals, or airports.
- Avoid exposing the device to direct sunlight for extended periods or placing it near heating devices.
- Do not place the device in extremely dusty, moist, or splash-prone environments, or on unstable surfaces.
- If the device emits smoke or strange odors, immediately remove the battery (if applicable) and contact the dealer.
- Transmission without an antenna installed can damage the device.
- Refer all servicing to well-trained professional technicians only.
Battery Cautions (for handheld transceivers, if used with this repeater)
- The power supply for transceivers is typically DC 7.4V. Use only the specified 7.4V 1800mAh Li-ion Battery (e.g., RB-589E).
- DO NOT repair or disassemble the battery yourself.
- DO NOT charge batteries in explosion-proof locations.
- Charge the transceiver using only the configured adapter. Do not use unapproved batteries.
- DO NOT put the battery in water or allow contact with wet materials.
- DO NOT short-circuit the battery.
- DO NOT attach, remove, or charge the battery in explosion-proof locations.
Explosion-Proof Compliance
The RS-589E explosion-proof marine transceiver (mentioned in the PDF, relevant for understanding the safety context of such devices) meets GB3836.1-2010 and GB3836.4-2010 standards for explosive environments. Its explosion-proof mark is Ex ib IIB T4 Gb, suitable for use in zones 1 and 2 containing IIA-IIB and T1-T4 explosive gas mixtures. The battery features dual output current limiting and short circuit protection, ensuring safe operation in hazardous gas environments.
Unpacking and Checking Equipment
Carefully unpack the product and check the main equipment and accessories against the list below. If any items are missing or damaged, please contact your dealer immediately.
| Accessories | Quantity |
|---|---|
| Repeater MD-8500 Unit | 1 |
| Power Cable | 1 |
| USB Programming Cable | 1 |
| User Manual | 1 |

Image: Contents of the TYT MD-8500 Repeater box, showing the repeater unit, user manual, and cables.
Getting Acquainted
Familiarize yourself with the external components and controls of your MD-8500 Repeater.

Image: Front view of the TYT MD-8500 Repeater, showing the power button, control buttons, and display.

Image: Rear view of the TYT MD-8500 Repeater, showing AC power input, DC 13.8V input, RX/TX antenna ports, and cooling fan.
External View Components
The front panel typically includes a power button, a display screen, navigation buttons (up/down/left/right), and a volume control knob. The rear panel features AC power input, DC 13.8V input, RX and TX antenna ports, and a cooling fan.
Keyboard Description and Shortcut Operation (for associated handheld transceivers)
While the MD-8500 is a repeater, its operation often involves associated handheld transceivers. The following describes common controls on such devices:
- [MENU] Key: Short press to enter menu mode, long press to enter/quit FM radio mode. Confirms settings.
- [EXIT] Key: Switches VFO, MR, CH modes; exits menu; switches channel/frequency in FM Radio mode.
- Up/Down Arrow Keys (∧/∨): Navigates menu items, adjusts frequency/channel.
- Left/Right Arrow Keys ([/]): Switches main/auxiliary frequency; revises menu item values; saves/deletes radio channels.
- Numeric Keys [0]~[9]: Manually key in frequency and DTMF dial.
- [*] Key: Long press for 2 seconds to toggle keyboard lock ON/OFF.
- [#] Key: Long press for 2 seconds to enter scan mode.
LCD Screen (for associated handheld transceivers)
The LCD screen displays various icons and information:
- Signal Strength Icon: Indicates signal strength.
- CT/DCS/VOX/ANI/DT Icons: Indicate CTCSS, DCS, Voice-Operated Transmit, Automatic Number Identification, and Dual-band Standby status.
- Battery Life Indicator: Shows remaining battery life.
- H/M/L Icons: Indicate High, Medium, or Low transmitting power.
- R Icon: Reverse frequency function.
- +/- Icons: Positive/negative offset.
- N Icon: Narrow band setting.
- S Icon: Power saving function.
- Keypad Lock Icon: Indicates keyboard is locked.
- Channel Number/Function Menu: Displays current channel or menu.
- Arrow: Indicates current working main band.
Preparation Work
Charging the Battery (for associated handheld transceivers)
- Connect the adapter cable to the desktop charger and then to AC power. The charger's orange light will illuminate for 2 seconds and then turn off.
- Insert the battery or transceiver with the battery into the battery groove, ensuring it is well connected and stable.
- The charger's red light will be on or flashing, indicating charging has started. A green light indicates full charge.
Warning: Do not charge in explosion-proof locations.
Install/Remove Battery Pack (for associated handheld transceivers)
- Lay the battery pack in the battery groove, press the battery bottom, and push forward until a click is heard, securing the battery pack.
- To remove, press the “PUSH” clip on top and gently pull downward.
Install/Remove Antenna (for associated handheld transceivers)
- Insert the supplied antenna into the antenna base.
- Tighten the antenna by rotating it clockwise until it is consistent with the base.
- To remove, rotate the antenna in an anti-clockwise direction.
Install Belt Clip (for associated handheld transceivers)
- Remove the battery first.
- Align the belt clip with the two screw holes on the transceiver.
- Screw on the belt clip using a screwdriver. Unscrew to remove.
Install External Loudspeaker/Microphone (for associated handheld transceivers)
- Open the rubber plug covering the jack.
- Insert the external loudspeaker/microphone into the jacks.
Warning: Do not insert/pull out external loudspeaker/microphone in explosion-proof locations.
Basic Operation
Power On (for associated handheld transceivers)
Rotate the [PWR/VOL] control knob clockwise to power on the transceiver. A beep tone will sound.
Volume Adjustment (for associated handheld transceivers)
Press the [MONI] key while rotating the [PWR/VOL] knob to adjust the volume.
Main/Auxiliary Band Selection, Single/Dual-Band Stand-by Convert (for associated handheld transceivers)
The main band supports both transmit and receive functions, while the auxiliary band is receive-only.
- Press the [Left Arrow] key to select the main band. The main band is indicated by an arrow.
- In dual-band standby, press the [Right Arrow] key to switch to single-band standby (the “DT” icon will disappear).
- In single-band standby, press the [Left Arrow] key to choose the main or auxiliary band.
- To return to dual-band standby from single-band, press the [Right Arrow] key (the “DT” icon will reappear).
PTT Transmitted (for associated handheld transceivers)
To transmit, press the [PTT] key. The red indication light will turn on. Speak into the microphone with a normal volume.
Notice: Keep your lips 3-5cm away from the microphone.
Signal Monitoring (for associated handheld transceivers)
For weak signals or channels with CTCSS/DCS, long press the [MONI] key to monitor the signal.
Torch Light Function (for associated handheld transceivers)
- Press the [MONI] key to enter torch light mode.
- Press [MONI] again to enter torch light SOS blinking mode.
- Press [MONI] a third time to shut down the torch light function.
Keypad Lock Function (for associated handheld transceivers)
- Press the [*] key for 2 seconds to lock the keyboard.
- Press the [*] key for 2 seconds again to unlock the keyboard.
FM Radio Function (for associated handheld transceivers)
- Long press the [MENU] key for 2 seconds to enter FM radio mode. The first line of the display will show “FM”, and the second line will show the current frequency.
- Long press the [MENU] key again for 2 seconds to exit FM radio mode.
- In FM Radio status, use the [Up Arrow] key to seek upward for radio stations, then press [#] to automatically seek and stop at a station with a signal.
- Use the [Down Arrow] key to seek downward for radio stations, then press [#] to automatically seek and stop at a station with a signal.
- You can also key in the radio frequency directly using the numeric keypad.
- The transceiver will automatically return to transceiver status if transmitting or if the [MONI] key is long-pressed. It will return to FM radio status after the signal disappears for 10 seconds.
Fell Alarm Function (for associated handheld transceivers)
Enable the fell alarm function via Menu No.20 “FALL” setting. The transceiver will automatically check its orientation. If the transceiver inclines at an angle less than 40 degrees for 10 seconds, it will enter alarm status and issue an alarm voice. The alarm stops when the device returns to a vertical stand for 2 seconds.
Main Functions Operation
Modes Selection (for associated handheld transceivers)
There are three display modes: Frequency, Channel, and Frequency Channel modes. These can be switched by pressing the [EXIT] key.
- Frequency Mode: Displays both main and auxiliary frequencies.
- Channel Mode: Displays both main and auxiliary channels.
- Frequency Channel Mode: Displays main frequency and auxiliary channel, or vice versa.
Note: In channel and frequency channel modes, you can set a user-defined name via Menu No.33 “CHNAME”.
Channel Save and Delete (for associated handheld transceivers)
Channel Save
- In frequency mode, set the desired frequency and other settings (CTCSS/DCS/offset) in the main frequency.
- Press the [MENU] key, select Menu No.34 “MEM-CH”, then press [MENU] again.
- The screen will show the channel number to be saved at the bottom. Use the [Left Arrow]/[Right Arrow] keys or numeric keypad to select a channel number.
- If a “CH-” icon is displayed, the channel already contains content.
- Press [MENU] to save and exit, or [EXIT] to quit without saving.
Single Channel Delete
- In standby mode, press the [MENU] key, select Menu No.35 “DEL-CH”, then press [MENU] again.
- The screen will show the channel number to be deleted at the bottom. Use the [Left Arrow]/[Right Arrow] keys or numeric keypad to select a channel number.
- If a “CH-” icon is displayed, it is a saved channel and can be deleted. If no “CH-” icon is displayed, it is an idle channel and cannot be deleted.
- Press [MENU] to confirm deletion, or [EXIT] to quit.
Scan (for associated handheld transceivers)
Scan Mode
Choose scan mode by editing Menu No.21 “SC-REV”. Options include:
- TO (Time Scan): Stops scanning when a signal is detected, stays for 5 seconds, then resumes scanning even if the signal persists.
- CO (Carrier Scan): Stops scanning when a signal is detected, resumes after the signal vanishes for 5 seconds, unless a new signal is detected.
- SE (Search Scan): Stops scanning when a signal is detected, stays on that channel, and quits scanning.
Channel Scan
In channel mode, long press the [# SCN] key to enter channel scan. Use the [Up Arrow]/[Down Arrow] keys to change scan direction. Hold [PTT] or [MONI] key to operate on the current channel; release to resume scanning after 5 seconds. Press any other key (except PTT/MONI) to end scanning.
Full-range Scan
In frequency mode, press the [# SCN] key to enter full-range scan. The frequency will gradually increase or decrease within the bandwidth. Use the [Up Arrow]/[Down Arrow] keys to change scan direction. Hold [PTT] or [MONI] key to operate on the current frequency; release to resume scanning after 5 seconds. Press any other key (except PTT/MONI) to end scanning.
DTMF Encode and Decode (for associated handheld transceivers)
Utilize DTMF for selective call and group call functions.
Manual Call
Press and hold the [PTT] key, then use the keyboard to enter characters (0-9, A, B, C, D, *, #).
Automatic Code Call
DTMF numbers (max 16 bits) can be saved into 8 automatic dial locations via PC programming software. To call out, press the [PF] programmable key, use [Up Arrow]/[Down Arrow] to select the saved DTMF number, then press [PTT].
Note: To use automatic code call, the [PF] programmable key must be set as the DTMF dial key.
DTMF Receive
- When your transceiver receives an ID number, a prompt tone will sound, and “P CALL” will display, indicating a successful call.
- When a group call code is received, a prompt tone will sound, and “G CALL” will display.
- You can press [PTT] to respond or listen. If no signal is received or transmitted for about 30 seconds, a “Du” tone will sound, and the transceiver will automatically quit the call.
ANI Personal Identification Code
To allow others to know your ID Code during a DTMF call, you need to add ANI call information. Key in the other party's ID code, then “*”, then your own 3-digit ID code (e.g., 123*456). The screen will display your ID (456) on the other party's transceiver.
Transmit 1750Hz Signal
Press [MENU], select Menu No.19 “PFK”, then [MENU] to edit. Choose “1750” and press [MENU] to confirm. The [PF] programmable key can then be used as the 1750 dial key to transmit the 1750Hz signal.
Note: The [PF] programmable key can be set as the 1750 dial key via programmable software.
Technical Specifications
General Specifications
- Frequency Range: 136-174MHz/400-480MHz
- Channel Capacity: 100
- Modulation Type: 16k0F3E (Wide band)/8k5F3E (Narrow band)
- Frequency Stability: ±2.5ppm
- Working Temperature: -30℃ to +60℃
- Working Voltage: 220V/110V AC ±15%/13.8V DC ±15%
- Dimensions: 133mm x 483mm x 330mm
- Weight: 16kg
- Antenna Impedance: 50Ω
Transmitter
- RF Power Output: 25W/50W (Duplexer options available)
- Radiated Spurious Emission: -36dBm < 1GHz, -30dBm < 1GHz
- FM Noise: 40dB @ 12.5KHz / 45dB @ 25KHz
- Modulation Distortion: <5%
- Digital Protocol: ETSI-TS102 361-1,-2,-3
- Frequency Modulation: 16kφ3E (analog) 4FSK (Digital)
- Modulation Limiting: ±2.5KHz @ 12.5KHz; ±5KHz @ 25KHz
Receiver
- Reference Sensitivity (Analog): 0.25uV @ 12dB SINAD
- Adjacent Channel Selectivity ETSI: 60dB @ 12.5KHz / 70dB @ 25KHz
- Reference Sensitivity (Digital): 0.22uV/-120dBm / 0.35uV/120dBm
- Spurious Response Rejection: ≥70dB
- Rated Audio Output: +1~-3dB
- Rated Audio Distortion: <5%
- FM Noise: ≥-45dB @ 25KHz / ≥40KHz @ 12.5KHz
Common Troubleshooting
| Trouble | Solution |
|---|---|
| Power-on no response. | Battery life exhausted (for handhelds), replace or charge. Battery not installed correctly, remove and reload. |
| Battery easily exhausted after full charging (for handhelds). | Battery pack life is ending, replace it. |
| Cannot contact with group members. | Communication distance out of effective range. Different frequency or CTCSS/DCS/DTMF signals are used, reset them. |
| Hear other voice (not from the same group) in the channel. | Change CTCSS/DCS/DTMF signal. Reset CTCSS/DCS/DTMF signal for all group members. |
| Short communication distance. | Check if antenna is well connected. Check if antenna is original. Check if battery voltage is normal (for handhelds). Adjust squelch level. |
User Tips
No specific user tips or frequently asked questions could be generated due to the absence of buyer reviews or Q&A content.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.
A user manual in PDF format is available for download. You can find it at: TYT MD-8500 User Manual (PDF)