JIKONG JK-B2A8S20P

Contents

JIKONG JK-B2A8S20P Smart BMS Instruction Manual

Model: JK-B2A8S20P | Brand: JIKONG

1. Introduction

The JIKONG JK-B2A8S20P is an intelligent Battery Management System (BMS) designed for large-capacity series lithium battery packs. It features voltage acquisition, high-current active balancing, overcharge/over-discharge protection, overcurrent protection, over-temperature protection, coulomb meter, Bluetooth communication, and optional GPS remote functionality. This BMS is compatible with various battery types, including Li-ion, LiFePO4, and LTO batteries, supporting 4S to 8S configurations.

The protection board utilizes energy transfer active balancing technology, capable of achieving a continuous 1A/2A balance current. This high-current active equalization technology ensures battery consistency, extends battery life, and delays aging. The system is managed via a mobile APP (Android and iOS) connected via Bluetooth, allowing users to monitor battery status, modify parameters, and control charge/discharge switches. Its compact size and comprehensive functions make it suitable for a wide range of applications, including small electric vehicles, energy storage systems, and solar power stations.

2. Safety Information

Always handle battery packs and BMS components with care. Ensure all connections are correct before powering on the system to prevent damage or injury. Do not expose the BMS to extreme temperatures or moisture. If you are unsure about any installation or operation steps, consult a qualified professional.

3. Product Features

  • Active Balancing: 1A/2A continuous active balancing current for optimal cell consistency.
  • Wide Compatibility: Supports 4S-8S Li-ion, LiFePO4, and LTO battery packs.
  • High Current Capacity: Maximum charging/discharging current of 200A.
  • Comprehensive Protection: Overcharge, over-discharge, overcurrent, over-temperature, low-temperature, and short-circuit protection.
  • Smart Monitoring: Bluetooth connectivity for mobile APP (Android/iOS) monitoring and parameter adjustment.
  • Data Acquisition: High-precision voltage (±3mV) and current acquisition.
  • Display Support: Supports external display screens for real-time information.
  • Optional Functions: Heating function for low-temperature environments, GPS communication, RS485/CAN communication.
  • Intelligent Sleep Mode: Reduces self-consumption when idle.
  • Emergency Switch: Provides 30 minutes of operation in critical situations.
JIKONG JK-B2A8S20P BMS with 3.2 and 4.3 inch display options
Figure 1: JIKONG JK-B2A8S20P BMS with optional 3.2-inch and 4.3-inch display units.
Exploded view of JIKONG BMS components including cooling aluminum alloy, MOS, MCU, NTC, and sampling line
Figure 2: Internal components of the BMS, highlighting the cooling aluminum alloy, MOS, JIKONG MCU, NTC, and sampling line.
Close-up of the JIKONG BMS circuit board showing the featured MCU chip
Figure 3: Selected core components, featuring the MCU for efficient operation.

4. Package Contents

The standard package for the JIKONG JK-B2A8S20P BMS includes the following items:

  • BMS Unit x 1
  • Sampling Line x 1 (70cm long)
  • NTC Temperature Sensor x 1 (40cm long)
  • Switch Key x 1 (50cm long)
JIKONG BMS Packing List showing the BMS unit, sampling line, NTC, and switch key
Figure 4: Contents included in the JIKONG BMS package.

5. Specifications

5.1. Basic Parameters

ParameterValueUnit
Supply Voltage10-36V
Operating Power Consumption<900mW
Operating Temperature-30 to 70°C
Max. Number of Collection Strings8String
Max. Balancing Current2A
Max. Charging Current200A
Max. Discharge Current200A
Max. Instantaneous Current400A
Max. Internal Loop Resistance0.4mΩ
Protective Plate Size (L*W*H)153*126*17.6mm
Finished Weight349g

5.2. Default Parameters

ParameterLi-ion (V)LiFePO4 (V)LTO (V)
Balancing Initial Voltage332
Max. Balancing Current (A)222
Unit Overcharge Voltage4.23.62.7
Single Overcharge Protection Recovery4.183.552.65
Monomer Undervoltage Protection2.822.61.8
Single Undervoltage Protection Recovery2.852.651.85
Automatic Shutdown Voltage2.82.51.7
SOC-0% Voltage2.92.61.85
SOC-100% Voltage4.183.52.65
Trigger Balancing Differential Pressure0.010.010.01
Charging Overcurrent Protection Delay (S)303030
Charging Overcurrent Protection Release Time (S)606060
Discharge Overcurrent Protection Delay (S)300300300
Discharge Overcurrent Protection Release Time (S)606060
Short-circuit Protection Delay (µS)150015001500
Short-circuit Protection Release Time (S)606060
Charging Overtemperature Protection (°C)707070
Charging Overtemperature Recovery (°C)606060
Discharge Overtemperature Protection (°C)707070
Discharge Overtemperature Recovery (°C)606060
Charging Low Temperature Protection (°C)-20-20-20
Charging Low Temperature Recovery (°C)-10-10-10
MOS Overtemperature Protection (°C)100100100
MOS Overtemperature Recovery (°C)808080
Device Address000
Discharge Precharge Time (S)000

5.3. Product Dimensions

Dimensions of JIKONG JK-B2A8S20P BMS: 153mm length, 126mm width, 17.6mm height
Figure 5: Dimensions of the JK-B2A8S20P BMS (153mm x 126mm x 17.6mm).

Note: The data tolerance range is ±2mm.

6. Installation and Wiring

Before installation, carefully inspect the package and the BMS unit for any signs of impact or damage. Handle the unit gently and avoid inverting it. The JK-B2A8S20P series protection board is suitable for 3-8 series lithium battery packs. The wiring method varies depending on the number of cells in your battery pack.

6.1. Wiring Method for 8-String Cells

Follow the diagram below for connecting an 8-string battery pack. Ensure all cables are connected correctly, insert the cable into the BMS, and connect the B-line and P-line to the battery.

Wiring diagram for an 8-string battery pack with JIKONG BMS, showing connections for total negative electrode P-, total positive electrode B-, and individual cell balance wires.
Figure 6: Wiring diagram for an 8-string cell configuration.

6.2. Wiring Method for 4-String Cells

For a 4-string battery pack, refer to the following diagram. The principles of connecting cables, inserting into the BMS, and connecting B-line and P-line remain the same.

Wiring diagram for a 4-string battery pack with JIKONG BMS, showing connections for total negative electrode P-, total positive electrode B-, and individual cell balance wires.
Figure 7: Wiring diagram for a 4-string cell configuration.

6.3. Interface Definitions

The BMS features various interfaces for communication, display, and sensors. Below is a detailed breakdown of the connectors and their pin definitions.

Detailed interface definitions for JIKONG JK-B2A8S20P and JK-B1A8S10P BMS models, showing pinouts for RS485, GPS, Display, Heat, NTC, and Sampling.
Figure 8: Interface definitions for JK-B2A8S20P (top) and JK-B1A8S10P (bottom) models, detailing connections for RS485, GPS, Display, Heat, NTC, and Sampling.

Important: Before powering on the protection board, double-check that the balance cable is properly connected and that the P- and B- lines are correctly wired. Ensure the protection board is securely fixed to the battery cells. Incorrect connections can lead to abnormal operation or even damage.

7. Operating Instructions

7.1. Device Activation

The BMS does not have a physical power-on switch. It is designed to activate in charging mode. After the battery assembly is complete, connect a charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, if you have an optional display screen and button, you can activate the BMS by inserting the cable into the display interface and pressing the button.7.2. Active Equalization

The active balancing function transfers energy from higher voltage cells to lower voltage cells. To use this feature, set the basic battery parameters (battery type, number of cells, capacity) in the JIKONG BMS APP. You can also adjust the balance trigger voltage difference (mV) and the balance current (recommended not to exceed 0.2C of battery capacity). Balancing automatically starts when the voltage difference between any two strings exceeds the set value and stops when it falls below the set value. If balancing is not required, it can be turned off in the APP's BMS control page.

7.3. GPS and Display Interface

The BMS includes a reserved GPS port for optional GPS modules, allowing for battery location tracking. It also has a display interface to connect JIKONG display screens for convenient real-time battery information viewing. Users can choose these options based on their needs.

7.4. Heating Function (Optional)

For low-temperature environments, the optional heating function uses a resistance heater or heating film to warm the battery, preventing performance degradation due to cold. The designed heating current is 4A. This function can be controlled via the APP's BMS control page. It is recommended to install a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit as a secondary safety measure.

7.5. Communication Function (Optional)

The BMS supports optional CAN/RS485 communication. Users can select the desired communication protocol and set the BMS address via the APP's BMS control page. Refer to the JIKONG Protection Board Communication Protocol document for specific details.

7.6. Intelligent Sleep Mode

The intelligent sleep function is standard. When the BMS is in standby (charging/discharging current less than 1A for 26 consecutive hours), it can enter sleep mode to reduce self-consumption. To reactivate, press a button (if available) or connect a charger.

7.7. Discharge Precharge Function (Optional)

The optional discharge precharge function has a default precharge time of 5 seconds. Users can enable or disable this function via the APP. Setting the precharge time to 0 disables the function.

7.8. Emergency Switch

The standard emergency switch function allows the BMS to continue charging and discharging for 30 minutes in case of over-temperature, over-discharge, over-charge, or cell string issues. This provides a temporary operational window to prevent immediate shutdown, which can be critical in certain situations.

8. APP Operation Instructions

8.1. APP Installation

Download the JIKONG BMS mobile APP by scanning the QR code below. An Android device requires Android Version 7 or higher.

QR code for JIKONG BMS mobile APP download
Figure 9: Scan this QR code to download the JIKONG BMS APP.

8.2. Parameter Setting

Once the APP is installed and the device is activated, you can access the parameter settings. Here you can customize various protection values such as overcharge, over-discharge, overcurrent, temperature, and balance settings. Always refer to the detailed parameter setting guide within the APP or the full PDF manual for specific instructions before making changes.

JIKONG BMS multi-screen display and data connection showing mobile app, PC software, and home storage display options
Figure 10: The JIKONG BMS supports multi-screen display and data connection via mobile APP, PC software, or dedicated home storage display.
JIKONG BMS mobile app interface showing battery voltage, current, temperature, SOC, alarms, and cycle count
Figure 11: Mobile APP interface for intelligent interaction and easy operation, displaying real-time battery data.
JIKONG BMS home storage dedicated display showing battery status and alarms
Figure 12: JIKONG home storage dedicated display for monitoring battery information.
Inverter communication protocol setup via host computer for JIKONG BMS
Figure 13: The inverter communication protocol can also be set through the host computer.
JIKONG BMS mobile app interface for selecting CAN protocols
Figure 14: Protocol docking and selection can be easily set up through the mobile APP.

9. Protection Functions and Troubleshooting

The JIKONG JK-B2A8S20P BMS is equipped with multiple protection mechanisms to ensure the safety and longevity of your battery pack. When a protection is triggered, the BMS will take action (e.g., stop charging/discharging) and will recover once the condition is resolved.

9.1. Charge Overvoltage Protection and Recovery

If any cell voltage exceeds the set overcharge protection voltage during charging, the BMS will stop charging. Charging will resume once all cell voltages drop below the overcharge recovery voltage. This prevents cell damage from overcharging.

9.2. Discharge Undervoltage Protection and Recovery

If any cell voltage drops below the set undervoltage protection voltage during discharge, the BMS will stop discharging. Discharge will resume once all cell voltages rise above the undervoltage recovery voltage (e.g., after charging). If any cell voltage falls below the automatic shutdown voltage, the BMS will shut down to protect the cells from deep discharge.

9.3. Charge Overcurrent Protection and Recovery

If the charging current exceeds the set continuous charging current for a specified delay time, the BMS will stop charging. Charging will resume after the overcurrent release time has passed. This protects against excessive charging currents.

9.4. Discharge Overcurrent Protection and Recovery

If the discharge current exceeds the set continuous discharge current for a specified delay time, the BMS will stop discharging. Discharge will resume after the overcurrent release time has passed. This protects against excessive discharge currents. Note: The maximum continuous discharge current should not exceed 200A.

9.5. Overtemperature Protection and Recovery

If the BMS detects that the temperature (charging or discharging) exceeds the set overtemperature protection value, the corresponding operation (charging or discharging) will stop. The operation will resume once the temperature drops below the recovery temperature. This protects the battery and BMS from heat damage.

9.6. Low Temperature Protection and Recovery

If the BMS detects that the charging temperature falls below the set low-temperature protection value, charging will stop. Charging will resume once the temperature rises above the recovery temperature. This prevents damage to cells from charging in cold conditions. For extremely cold regions, consider using the optional heating function.

9.7. Short Circuit Protection and Recovery

The BMS includes standard short-circuit protection. If a short circuit is detected, the BMS will immediately stop the operation. After a specified recovery time, the BMS will attempt to resume operation. If the short circuit persists, it will trigger again. Users can adjust the short-circuit protection delay and recovery time via the APP if needed, especially when connecting loads with high inrush current or chargers with high peak output.

10. Maintenance

The JIKONG BMS is designed for durability and minimal maintenance. However, regular checks can help ensure optimal performance and longevity:

  • Visual Inspection: Periodically inspect the BMS and wiring for any signs of damage, corrosion, or loose connections.
  • Software Updates: Check the JIKONG official website or APP for any firmware updates to ensure you have the latest features and bug fixes.
  • Cleanliness: Keep the BMS free from dust and debris. Use a soft, dry cloth for cleaning.
  • Temperature Monitoring: Ensure the BMS operates within its specified temperature range. If using the heating function, verify its proper operation in cold conditions.

11. User Tips

  • Initial Setup: Always connect the balance wires first, then the B- and P- lines. Double-check all connections before applying power.
  • APP Customization: Take advantage of the mobile APP to fine-tune protection parameters to match your specific battery chemistry and application needs.
  • Active Balancing: For new battery packs or after significant use, monitor the active balancing function to ensure cell voltages remain consistent. Adjust the balancing current if necessary.
  • Temperature Management: If operating in cold climates, consider enabling the heating function and ensure proper insulation for your battery pack.
  • Firmware Updates: Regularly check for and install any available firmware updates for your BMS to benefit from performance improvements and new features.
  • Documentation: Keep this manual and the full PDF user manual accessible for reference, especially for detailed parameter settings and wiring diagrams.

12. Support and Further Documentation

For detailed technical specifications, advanced parameter settings, and comprehensive wiring diagrams, please refer to the official user manual PDF:

View User Manual (PDF)

For further assistance or inquiries, please visit the JIKONG official website or contact their customer support.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.