JIKONG JK-B2A8S20P

Contents

JIKONG JK-B2A8S20P Smart BMS User Manual

Model: JK-B2A8S20P | Brand: JIKONG

1. Introduction and Overview

The JIKONG JK-B2A8S20P is an intelligent Battery Management System (BMS) designed for large-capacity series lithium battery packs. It supports 4 to 8 series battery configurations for Li-ion, LiFePO4, and LTO battery types.

This BMS offers comprehensive battery management, including voltage acquisition, high current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS remote functionality.

The active balancing technology ensures energy transfer from higher-voltage cells to lower-voltage cells, achieving voltage balance with minimal energy loss. This process operates continuously during charging, discharging, or idle states until the voltage difference is within a set range. This non-lossy balancing method is highly efficient and suitable for larger battery capacities.

JIKONG JK-B2A8S20P BMS with display options
JIKONG JK-B2A8S20P BMS with 3.2 and 4.3 inch display options.
JIKONG JK-B2A8S20P BMS key features
Key features of the JIKONG JK-B2A8S20P BMS, including Bluetooth/Display, 2A Balancing Current, 4S-8S support, and 200A Charge/Discharge.

2. Setup and Installation

2.1. Unpacking and Inspection

Upon receiving your JIKONG BMS, handle the packaging and the protection board gently. Before opening, inspect the package for any signs of impact or damage. Ensure all components listed in the packing list are present and in good condition.

2.2. Packing List

  • BMS x 1
  • Sampling Cable x 1 (70cm long)
  • NTC (Temperature Sensor) x 1 (40cm long)
  • Switch Key x 1 (50cm long)
JIKONG BMS Packing List
Contents of the JIKONG BMS package.

2.3. Wiring Diagrams

The JK-B2A8S20P BMS is suitable for 3-8 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Always ensure correct connections to avoid damage.

Wiring for 8-String Cells

Wiring diagram for 8-string battery cells
Detailed wiring diagram for an 8-string cell battery pack with the JK-BxA8S-20P BMS.

Wiring for 4-String Cells

Wiring diagram for 4-string battery cells
Detailed wiring diagram for a 4-string cell battery pack with the JK-BxA8S-20P BMS.

2.4. Interface Definition

The BMS features various interfaces for connectivity and functionality:

ConnectorPin NumberNameDefinition
Balance & Acquisition (XH-10AW)1B-Total negative battery
2B1The first battery positive
3B2The second battery positive
4B3The third battery positive
5B4The fourth battery positive
6B5The fifth battery positive
7B6The sixth battery positive
8B7The seventh battery positive
9B8The eighth battery positive
10B+Protection board power supply, connected to the battery
Heating Interface (A1254WF-7A)1-5HT-Heater element negative electrode
6CD+Charge indication input positive terminal
7CD-Charge indication input negative terminal
P-P-Connect to external load or negative terminal of charger
B-B-Connect to the negative battery terminal
Display Interface (A1254WF-6A)1VCCDisplay power output
GPS Interface (1.25T-4PWT)1VGPSPower output, voltage close to B+
2TXUART TX, 3.3V
3RXUART RX, 3.3V
4GNDPower/signal ground
Communication Interface (A1254WF-3A)1DNCAN L/RS485-B signal negative
2DPCAN H/RS485-A signal positive
3GNDSignal ground
Temperature Interface (HY2.0-4P)1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B

3. Operating Instructions

3.1. APP Installation

The JIKONG BMS features a mobile application for Android and iOS operating systems. Scan the QR code below to download the official APP. Android devices require a minimum of Android 7.

QR code for JIKONG BMS Mobile APP
QR code to download the JIKONG BMS Mobile APP.

3.2. Device Activation

Before powering on the protection board, double-check that the balance cables are correctly connected and that the P- and B- terminals are properly wired. Ensure the protection board is securely fixed to the battery pack. Incorrect connections can lead to abnormal operation or damage.

The BMS does not have a physical power-on switch. It is designed for charging activation: after battery assembly, connect a charger (with voltage 2V higher than battery voltage) to activate the board. Alternatively, if you have an optional display screen and button, you can activate the BMS by inserting the cable into the display interface and pressing the button.

3.3. Active Equalization

The active equalization function transfers energy from high-voltage cells to low-voltage cells. Before using, set basic battery parameters in the APP, including battery type, number of cells, battery capacity, and trigger voltage difference. The default balance current is 1A/2A. It is recommended that the balance current does not exceed 0.2C of the battery capacity. The balancing switch can be turned off in the APP's BMS control page if not needed.

Active Balancing Diagram
Diagram illustrating the principle of active balancing (lossless balancing) in a battery pack.

3.4. GPS and Display Interface

The BMS includes a reserved GPS port for optional GPS modules, allowing for battery location tracking. It also has a display interface for connecting JIKONG display screens to view battery information conveniently.

Mobile APP Interface
Mobile APP interface showing real-time battery data like voltage, current, temperature, SOC, alarms, and cycles.
PC Software Interface
PC software interface for detailed monitoring and parameter settings of the JIKONG BMS.

3.5. Heating Function (Optional)

The optional heating function uses a resistance heater or heating film to warm the battery in low-temperature conditions, preventing reduced battery activity. The designed heating current is 4A. Users can enable/disable this function via the APP. For secondary protection, it's recommended to install a normally closed temperature switch (45°C to 65°C) in series with the heating circuit.

4. Protection Functions and Troubleshooting

The JIKONG BMS includes various protection mechanisms to ensure battery safety and longevity. When a protection is triggered, the BMS will take action to prevent damage and will recover once conditions return to normal. Troubleshooting often involves checking APP parameters and external connections.

4.1. Charge Overvoltage Protection and Recovery

The BMS protects against overvoltage during charging. Users can set the single overcharge protection voltage and recovery voltage in the APP. If any cell exceeds the set voltage, charging will stop. Charging resumes when all cell voltages drop below the recovery voltage.

4.2. Discharge Undervoltage Protection and Recovery

This function prevents over-discharge. Users can set the undervoltage protection voltage, recovery voltage, and automatic shutdown voltage in the APP. If any cell drops below the protection voltage during discharge, discharge will stop. Discharge resumes when all cell voltages rise above the recovery voltage. If any cell drops below the automatic shutdown voltage, the BMS will automatically shut down.

4.3. Charge Overcurrent Protection and Recovery

Protects against excessive charging current. Users can set continuous charging current, overcurrent delay, and recovery time in the APP. If the charging current exceeds the set value for the specified delay, charging will stop. Charging resumes after the set recovery time.

4.4. Discharge Overcurrent Protection and Recovery

Protects against excessive discharging current. Users can set continuous discharge current, overcurrent delay, and recovery time in the APP. If the discharge current exceeds the set value for the specified delay, discharge will stop. Discharge resumes after the set recovery time. Note: Maximum continuous discharge current should not exceed 200A.

4.5. Overtemperature Protection and Recovery

The BMS monitors battery temperature during charge and discharge. Users can set overtemperature protection and recovery values in the APP. If the temperature exceeds the set limit, charging or discharging will stop. Operation resumes when the temperature drops below the recovery value.

4.6. Low Temperature Protection and Recovery

Protects against charging at dangerously low temperatures. Users can set low temperature protection and recovery values in the APP. If the temperature drops below the set limit during charging, charging will stop. Charging resumes when the temperature rises above the recovery value. For extremely cold environments, consider using the optional heating function.

4.7. Short Circuit Protection and Recovery

This function is standard and does not require manual current settings. Users can adjust the short circuit protection delay and recovery time in the APP. If a short circuit occurs, the BMS will trigger protection. Increasing the delay can help prevent false triggers from high instantaneous currents during charger startup or load connection.

4.8. Discharge Precharge Function (Optional)

This optional function allows for precharging before discharge. The default precharge time is 5 seconds. Users can enable/disable this function and adjust the time via the APP. Setting the time to 0 disables precharge.

4.9. Emergency Switch

The emergency switch function, accessible via the APP, allows the BMS to maintain charge and discharge for 30 minutes even if over-temperature, over-discharge, over-charge, or cell drop issues occur. This provides a temporary operational window in critical situations.

4.10. Intelligent Sleep

The intelligent sleep function, configurable in the APP, puts the BMS into a low-power standby mode (if charge/discharge current is less than 1A for 26 consecutive hours) to reduce self-consumption. The BMS can be reactivated by pressing a button or connecting a charger.

4.11. Communication Function

The BMS supports optional CAN/RS485 communication. Users can select the desired protocol and configure the address and communication protocol via the APP based on their specific requirements. Refer to the JIKONG Protection Board communication protocol document for details.

5. Specifications

5.1. Basic Parameters

ParameterValueUnit
Supply Voltage10-36V
Operating Power Consumption<900mW
Operating Temperature-30 to 70°C
Maximum Number of Collection Strings8String
Maximum Balancing Current2A
Maximum Charging Current200A
Maximum Discharge Current200A
Maximum Instantaneous Current400A
Maximum Internal Loop Resistance0.4mΩ
Finished Weight349g
JIKONG BMS Product Specifications Table
Detailed product specifications for various JIKONG BMS models.

5.2. Default Parameters (JK-B2A8S20P)

ParameterLi-ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Maximum Balancing Current222A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charging Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay150015001500µS
Short Circuit Protection Release Time606060S
Charging Overtemperature Protection707070°C
Charging Overtemperature Recovery606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charging Low Temperature Recovery-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Recovery808080°C
Device Address000/
Discharge Precharge Time000S

5.3. Product Dimensions

The dimensions of the JK-B2A8S20P series protection board are 153mm x 126mm x 17.6mm.

JIKONG JK-B2A8S20P BMS Dimensions
Dimensional drawing of the JIKONG JK-B2A8S20P BMS.

6. Maintenance

To ensure optimal performance and longevity of your JIKONG BMS, follow these general maintenance guidelines:

  • Keep Clean: Regularly clean the BMS and its connections to prevent dust and debris buildup, which can affect performance and heat dissipation.
  • Avoid Physical Damage: Protect the BMS from impacts, vibrations, and moisture. Ensure it is securely mounted in its intended location.
  • Ensure Proper Ventilation: If the BMS is enclosed, ensure adequate airflow to prevent overheating, especially during high current operation or when the heating function is active.
  • Regularly Check Connections: Periodically inspect all wiring connections (balance cables, power cables, sensor cables) to ensure they are secure and free from corrosion. Loose connections can lead to unstable operation or damage.
  • Monitor via APP: Use the mobile APP or PC software to regularly monitor battery parameters and BMS status. This helps in early detection of potential issues.

7. User Tips

While no specific user reviews or Q&A data were provided, here are some general tips for maximizing your JIKONG BMS experience:

  • Customize Parameters: Take advantage of the APP's parameter settings to fine-tune protection thresholds and balancing currents according to your specific battery chemistry and usage patterns.
  • Monitor Actively: Regularly check the battery status via the mobile APP. This allows you to observe cell voltages, temperatures, and overall battery health, helping you understand your battery's behavior and identify any anomalies early.
  • Consider Optional Accessories: If your application requires precise location tracking or a dedicated visual interface, consider integrating the optional GPS module or a JIKONG display screen.
  • Proper Cable Management: Ensure all cables are neatly routed and secured to prevent accidental disconnections or damage from vibration.

8. Warranty and Support

For detailed warranty information and technical support, please refer to the official JIKONG documentation or contact your seller. The comprehensive user manual (PDF) provides in-depth information on product usage and troubleshooting.

You can access the full user manual PDF here: JIKONG JK-BxA8S-20P User Manual (PDF)


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.