1. Introduction
The EXFO MaxTester 710B-M1 is a robust and intuitive Optical Time Domain Reflectometer (OTDR) designed for efficient and accurate fiber optic network testing. This compact, handheld device is ideal for field technicians, offering a user-friendly interface and comprehensive testing capabilities for single-mode fibers. It supports dual wavelengths (1310/1550nm) and provides a dynamic range of 30/28dB, making it suitable for various fiber installation and maintenance tasks.

2. Package Contents
Before using your EXFO MaxTester 710B-M1, please verify that all items are present in the package:
- EXFO MaxTester 710B-M1 OTDR Unit
- AC/DC Power Adapter
- Power Cord
- USB Cable
- Quick Reference Guide
- Summary View Documentation
- Event Table Icons Documentation
- Carrying Case
- Fiber Optic Patch Cable (may vary by configuration)
- Visual Fault Locator (VFL) (may vary by configuration)


3. Device Overview
Familiarize yourself with the physical features and connection points of your MaxTester 710B-M1.

Key Components:
- OTDR Port: For connecting to the fiber under test.
- iOLM Port: For Intelligent Optical Link Mapper functionality.
- USB 2.0 Ports: For connecting to external devices like USB drives or a PC.
- RJ-45 LAN Port: For network connectivity (10/100 Mbit/s).
- Power Input: For connecting the AC/DC power adapter.

4. Setup
4.1 Charging the Battery
- Connect the AC/DC power adapter to the power input port on the MaxTester 710B-M1.
- Plug the power cord into a suitable electrical outlet (100-240 VAC, 50-60 Hz).
- The device will begin charging. A full charge provides approximately 12 hours of operation.
4.2 Powering On/Off
- To Power On: Press and hold the power button until the EXFO logo appears on the screen.
- To Power Off: Press and hold the power button until a shutdown prompt appears, then confirm.
4.3 Initial Configuration
Upon first power-on or after a factory reset, you may need to configure basic settings such as language, date, and time. Follow the on-screen prompts to complete this setup.
4.4 Connecting to a PC or Network
- USB Connection: Use the provided USB cable to connect the MaxTester to a computer for data transfer or software updates.
- LAN Connection: Connect an Ethernet cable to the RJ-45 port to integrate the device into a local area network for remote management or data sharing.
5. Operating Instructions
5.1 Basic OTDR Testing
- Clean Connectors: Always ensure fiber optic connectors are clean before connecting them to the OTDR. Use appropriate fiber cleaning tools.
- Connect Fiber: Connect the fiber under test to the OTDR port using a suitable launch cable if necessary.
- Select Mode: On the touchscreen, navigate to the 'OTDR' tab.
- Configure Test Parameters: Set parameters such as wavelength (1310nm or 1550nm), pulse width, and distance range according to the fiber type and length being tested.
- Start Test: Press the 'Start' button to initiate the OTDR trace.
- Analyze Results: The device will display the fiber trace, event table, and summary results. Analyze the trace for events like splices, connectors, and breaks.
5.2 Using iOLM (Intelligent Optical Link Mapper)
The iOLM feature simplifies OTDR testing by providing a single-button operation that automatically sets parameters, performs multiple acquisitions, and presents results in an icon-based link view. This eliminates the need for complex trace analysis.
- Connect Fiber: Ensure the fiber is properly connected to the iOLM port.
- Select iOLM Tab: Tap the 'iOLM' tab on the display.
- Start Test: Press the 'Start' button. The iOLM will automatically perform the necessary tests.
- Review Link Map: The results will be displayed as a clear, intuitive link map with icons representing different events and their characteristics.
5.3 Saving and Managing Data
Test results can be saved to the device's internal memory (2 GB, typical 20,000 OTDR traces) or transferred to external storage via USB.
- Saving: After a test, use the 'Save' option on the screen to store the results.
- Transferring: Connect the device to a PC via USB and access the internal storage to copy files.
6. Maintenance
6.1 Cleaning the Device
- Exterior: Use a soft, damp cloth to clean the exterior of the device. Avoid abrasive cleaners or solvents.
- Touchscreen: Use a microfiber cloth specifically designed for electronic screens. Do not apply excessive pressure.
- Fiber Optic Ports: Regularly clean the OTDR and iOLM ports using approved fiber optic cleaning sticks and solutions to prevent contamination and ensure accurate measurements. Refer to industry best practices for fiber cleaning.
6.2 Battery Care
- To maximize battery life, avoid fully discharging the lithium-polymer battery frequently.
- Store the device in a cool, dry place when not in use for extended periods.
- If storing for a long time, ensure the battery is charged to approximately 50%.
6.3 Software Updates
Periodically check the EXFO website for firmware updates to ensure your device has the latest features and performance enhancements. Updates can typically be installed via USB connection to a PC.
7. Troubleshooting
This section addresses common issues you might encounter with your MaxTester 710B-M1.
7.1 Device Not Powering On
- Ensure the battery is sufficiently charged. Connect the device to the AC/DC adapter and try again.
- Verify the power adapter and cable are securely connected and functioning correctly.
7.2 No OTDR Trace or Inaccurate Readings
- Check Fiber Connection: Ensure the fiber under test is properly connected to the OTDR port and that connectors are clean.
- Verify Launch Cable: If using a launch cable, ensure it is in good condition and properly connected.
- Correct Parameters: Confirm that the selected wavelength, pulse width, and distance range match the fiber being tested.
- Dirty Connectors: Contaminated fiber connectors are a common cause of poor readings. Clean all connectors thoroughly.
7.3 Touchscreen Unresponsive
- Perform a soft reset by holding the power button until the device restarts.
- Ensure the screen is clean and free from debris or moisture.
8. Specifications
The following table details the technical specifications of the EXFO MaxTester 710B-M1.

| Feature | Specification |
|---|---|
| Model | MAXTESTER 710B |
| Display | Touchscreen, Two USB 2.0 ports, RJ-45 LAN 10/100 Mbit/s |
| Storage | 2 GB internal memory (20 000 OTDR traces, typical) |
| Batteries | Rechargeable lithium-polymer battery, 12 hours of operation (Telcordia TR-NWT-001138) |
| Power supply | AC/DC adapter, input 100-240 VAC, 50-60 Hz, 9-16 V DCIN 15 Watts minimum |
| Wavelength | 1310/1550nm |
| Dynamic range | 30/28dB |
| Event dead zone | 1m |
| Attenuation dead zone | 4m |
| Distance range | 0.1 to 160 km |
| Pulse width | 5 ns to 20 us |
| Linearity | ±0.05dB |
| Loss threshold | 0.01dB |
| Loss resolution | 0.001dB |
| Sampling resolution | 0.04 to 5m |
| Sampling points | Up to 256 000 |
| Fiber Type | Single Mode |
| Connector Type | Hybrid |
9. User Tips
- Understand Your Equipment: If you're new to OTDRs, take time to familiarize yourself with the device's functions and included accessories. The carrying case is designed for protection and portability.
- Always Clean First: The most critical step for accurate fiber testing is ensuring all connectors are spotless. A single speck of dust can cause significant measurement errors.
- Use iOLM for Simplicity: For quick and easy link characterization without deep OTDR trace analysis, leverage the iOLM feature. It provides clear, actionable results.
- Regular Data Backup: Periodically transfer your saved traces and test results to a computer to prevent data loss and for comprehensive reporting.
10. Warranty and Support
For specific warranty information, technical support, or service inquiries, please refer to the official EXFO documentation included with your product or visit the EXFO website. Keep your proof of purchase and serial number handy when contacting support.