Introduction
This manual provides essential information regarding the spare parts for your EHEIM Professionel external filter. It covers an overview of common replacement components, general guidance for installation, maintenance, and troubleshooting. Please refer to the specific diagrams for your filter model when performing any maintenance or part replacement.
Compatible Filter Models
These spare parts are designed for the following EHEIM Professionel external filter series:
- EHEIM Professionel: 2222, 2224, 2322, 2324
- EHEIM Professionel: 2226, 2228, 2326, 2328
- EHEIM Professionel: 2227, 2229
- EHEIM Experience: 2426 (for specific parts like sealing gasket)
- EHEIM Professionel 2: 2026/2126, 2028/2128 (for specific parts like sealing gasket)
Common Spare Parts Overview
Below is an overview of frequently replaced spare parts. Always verify the part number for your specific filter model.
Hose Clamp
Order No: 7444100
Used to secure hoses to connectors, preventing leaks.
Locking Clamp for Adapter
Order No: 7343118
Secures the adapter to the filter head, ensuring a tight seal.
Sealing Gasket
Order No: 7343158
Crucial for maintaining a watertight seal between filter components. Compatible with various Professionel and Experience models.
Pump Cover
Order No: 7656300
Protects the impeller and motor assembly within the filter head.
EZ Clip
Order No: 7445058
Small clip used for securing various internal filter components.
Setup and Installation of Spare Parts
Replacing spare parts typically involves disassembling a portion of your filter. Always ensure the filter is unplugged and disconnected from the aquarium before proceeding.
- Preparation: Unplug the filter from the power outlet. Close the inlet and outlet valves (if applicable) and disconnect the hoses from the filter unit.
- Disassembly: Carefully open the filter head by releasing the locking clips. Remove the filter media baskets.
- Part Replacement: Identify the specific part to be replaced using the diagrams below. Remove the old part and install the new spare part, ensuring it fits correctly and securely. Pay close attention to the orientation of gaskets and clips.
- Reassembly: Reassemble the filter in reverse order of disassembly. Ensure all seals are properly seated and locking mechanisms are engaged.
- Testing: Reconnect hoses and open valves. Prime the filter (if necessary, refer to your main filter manual) and plug it back in. Check for any leaks immediately.
Detailed Diagrams for Specific Models:
EHEIM Professionel 2222/2224 Exploded View
This diagram illustrates the components of the EHEIM Professionel 2222 and 2224 external filters, including the filter head (4004943), impeller (7343418), various clamps (7445180, 7343118), filter pads (2616225, 2616220), and hose connections (4014100, 7286500).
EHEIM Professionel 2226/2228/2326/2328 Exploded View
This diagram shows the internal structure and part numbers for EHEIM Professionel 2226, 2228, 2326, and 2328 filters. Key components include filter baskets (7444450), sealing rings (7271958), and optional heaters (7655008) with their holders (7444490).
Partial Part List for 2226/2228/2326/2328:
| Part No. | Description |
|---|---|
| 2616250 | Filter media set |
| 4004710 | Outlet pipe |
| 4004943 | Filter head |
| 4008382 | Hose 12/16mm (3m) |
| 7271958 | Sealing ring / Gasket |
| 7343118 | Locking clamp for adapter |
| 7444100 | Hose clamp |
| 7445058 | EZ clip |
| 7656300 | Pump cover |
EHEIM Professionel 2226/2228 Exploded View (Alternative)
This diagram provides another detailed view of the EHEIM Professionel 2226 and 2228 filters, highlighting components such as the filter head (4005943, 4004943), impeller (7343150), and various filter media (2616265, 2616260).
Maintenance
Regular maintenance and timely replacement of worn parts are crucial for the optimal performance and longevity of your EHEIM external filter.
- Sealing Gaskets: Inspect all sealing gaskets (e.g., filter head gasket, impeller cover gasket) during routine filter cleaning. Replace them if they appear brittle, cracked, or deformed to prevent leaks.
- Impeller and Shaft: Check the impeller and its ceramic shaft for wear, cracks, or debris buildup. A worn impeller can lead to reduced flow or increased noise. Replace if damaged.
- Hoses and Clamps: Periodically inspect hoses for kinks, hardening, or algae buildup. Ensure hose clamps are tight and not corroded. Replace hoses or clamps as needed.
- Filter Baskets and Media: While not strictly spare parts, ensure filter baskets are intact and not broken. Replace filter media according to your filter's specific recommendations.
Troubleshooting Common Issues
Many common filter problems can be resolved by inspecting and replacing specific spare parts.
| Problem | Possible Cause (Spare Part Related) | Solution |
|---|---|---|
| Water Leakage | Worn or improperly seated sealing gasket (e.g., 7343158), loose hose clamp (7444100), cracked filter head. | Inspect and replace faulty gaskets. Tighten hose clamps. Check filter head for damage. |
| Reduced Flow Rate | Worn impeller (e.g., 7343418), clogged impeller chamber, damaged pump cover (7656300). | Clean impeller and chamber. Replace worn impeller or damaged pump cover. |
| Loud Noise/Vibration | Worn impeller (e.g., 7343418), damaged impeller shaft (e.g., 7342358), foreign object in impeller chamber. | Inspect and replace impeller/shaft. Remove any obstructions. |
| Filter Not Starting | Impeller jammed or damaged, motor failure (less common for spare parts). | Check and clear impeller. Replace impeller if damaged. |
Specifications
- Material: Primarily Plastic components, with rubber/silicone gaskets and ceramic shafts.
- Origin: Germany (De(origin))
- High-concerned chemical: None
User Tips
- Always keep a spare set of essential wear-and-tear parts like gaskets and impellers on hand to minimize downtime during maintenance.
- When replacing gaskets, apply a thin layer of silicone grease (aquarium safe) to help with sealing and prevent premature wear.
- Refer to your original EHEIM filter manual for model-specific instructions and detailed diagrams, in addition to the general guidance provided here.
Warranty and Support
EHEIM spare parts are manufactured to high-quality standards. For specific warranty information regarding individual spare parts, please refer to the packaging or contact EHEIM customer support directly. Ensure you purchase genuine EHEIM spare parts to guarantee compatibility and performance.
For further assistance or technical support, please visit the official EHEIM website or contact their authorized service centers.
