1. Introduction
The PowMr MPPT Solar Charge Controller is an advanced maximum power point tracking (MPPT) technology-based device designed for solar systems. It boasts a charge controller conversion efficiency of up to 98% and a peak conversion efficiency of up to 97%, ensuring optimal performance for your solar power setup. These controllers are compatible with various lithium and lead-acid batteries and support system voltages of 12V or 24V.

2. Key Features
- MPPT 25A, 35A, and 45A solar charge controller models available.
- Innovative MPPT technology with tracking efficiency up to 99% and peak conversion efficiency up to 97%.
- Built-in DSP controller for high performance.
- Automatic voltage switch for 12V/24V battery banks.
- 3-stage charging algorithm to optimize battery performance and longevity.
- Comprehensive protection features: Overcharge protection, Input PV polarity reverse protection, Output limited current protection, Over-temperature protection.
- Troubleshooting promotion function.
- User-friendly design for easy and quick installation.
- Equipped with a built-in temperature sensor.
- Lithium battery activation function.
3. Package Contents
Upon opening the package, you should find the following items:
- 1x PowMr MPPT Solar Charge Controller (POW-M25-PRO, POW-M35-PRO, or POW-M45-PRO model)
- 1x User Manual
- 1x Installation Guide Card
- 1x Set of Screws for mounting
4. Setup and Installation
Follow these steps for safe and correct installation of your solar charge controller. Always ensure all power sources are disconnected before making any connections.
4.1. Wiring Diagram

4.2. Connection Steps
- **Wiring the Battery:** Ensure the battery breaker is open. Connect the battery to the controller.
- **Wiring Solar Panels:** Ensure the PV breaker is open. Connect the solar panels to the controller.
- **Connect Battery (Controller Power On):** Close the battery breaker. The controller should power on.
- **Connect Solar Panels (Charging):** Close both the PV and battery breakers. The system will begin charging.

The user-friendly design ensures easy and quick installation. Remove the port cover, connect the battery, connect the PV array, connect the DC load, then reassemble the port cover. Start up the controller by closing the appropriate breakers.
5. Operating Instructions
5.1. Multiple Load Work Modes
The controller supports various load work modes to suit your needs:
- **00H (Load Turn OFF):** The load output is always off.
- **24H (Load always Turn ON):** The load output is always on.
- **01H~23H (Time control):** Allows you to set the duration for which the load is turned on (e.g., 08H for 8 hours).

5.2. Battery Type Selection
The controller is compatible with multiple battery types, including AGM, GEL, FLD (Flooded), LI (Lithium), and SLA (Sealed Lead-Acid). To select the battery type:
- Long press the BAT/▲ key to enter the setting program.
- Use the BAT/▲ and DC/▼ keys to toggle through the battery type options.
- Press the SET/⚙ key to save and confirm.
- If you select "User-defined battery type" (USE), you can proceed with setting specific battery parameters.
| Sequence | Display | Battery Type |
|---|---|---|
| 1 | SEL | Sealed Lead-acid battery |
| 2 | GEL | Gel sealed lead-acid battery |
| 3 | FLD | Flooded lead-acid battery |
| 4 | L04 | 4S Lithium iron phosphate battery |
| 5 | L07 | 7S Lithium iron phosphate battery |
| 6 | L08 | 8S Lithium iron phosphate battery |
| 7 | N03 | 3S Lithium-ion battery |
| 8 | N06 | 6S Lithium-ion battery |
| 9 | N07 | 7S Lithium-ion battery |
| 10 | USE | User-defined |

5.3. LCD Screen and Working Modes
The controller features a backlight LCD screen that displays various parameters and working modes:
- **3.0:** Night mode, no charging.
- **4.0:** MPPT Charging Mode.
- **7.0:** Boost Charging Mode.
- **8.0:** Floating Charge Mode.

5.4. Calibrating Battery Voltage
If there is a discrepancy between the battery voltage monitored by the controller and the value measured by a multimeter, you can calibrate the battery voltage using this setting:
- Long press the BAT/▲ key to enter the setting program.
- Use the BAT/▲ and DC/▼ keys to adjust the value.
- Press the SET/⚙ key to save and confirm.
6. Safety and Protections
The PowMr MPPT Solar Charge Controller is equipped with 9 built-in electronic protections to actively monitor changes in voltage, current, and load for efficient and safe battery charging and system operation. These include:
- PV over current protection
- PV short circuit protection
- PV reverse polarity protection
- Battery reverse polarity protection
- Battery over voltage protection
- Battery over discharge protection
- Lithium battery low temperature protection
- Load overcurrent protection
- Over-temperature protection

7. Troubleshooting
The controller features a troubleshooting function that displays error codes on the LCD screen. Refer to the table below for common fault codes, their causes, and solutions.
| Fault Code | Fault Cause | Solution |
|---|---|---|
| 18 | Input photovoltaic voltage too low | Increase the number of solar panels or connect them in series to raise the photovoltaic input voltage. |
| 60 | Overtemperature protection | Allow the equipment to cool to below the recovery temperature to resume normal charging and discharging. |
| 63 | Battery voltage too high | Measure to confirm if battery voltage exceeds rated voltage and disconnect photovoltaic array circuit breaker. |
| 65 | Battery voltage too low | Charge the battery until voltage exceeds the undervoltage recovery point. Refer to '3.7 Default Parameters for Different Battery Types' for specific details. |
| 71 | Input photovoltaic voltage too high | Reduce the number of photovoltaic arrays connected to the controller to lower photovoltaic input; or adjust series and parallel connections to reduce voltage or current values. |
| 73 | Overcharging current | Reduce output terminal load to ensure total load is within rated limits of the controller and battery. |
| 72 | Overdischarging current | Reduce output terminal load to ensure total load is within rated limits of the controller and battery. |
For any other error codes or persistent issues, please consult the full user manual or contact customer support.
8. Specifications
| Parameter | 25A Model | 35A Model | 45A Model |
|---|---|---|---|
| Solar Input Parameters | |||
| Max. PV Open-Circuit Voltage | 100V | ||
| Max. Input Power | |||
| For 12V System | 300W | 420W | 540W |
| For 24V System | 600W | 840W | 1080W |
| Input Voltage Range | |||
| For 12V System | <60V | <80V | <100V |
| For 24V System | <60V | <80V | <100V |
| Battery Charging Parameters | |||
| Charging Technology | MPPT | ||
| Charging Algorithm | 3 Stages | ||
| Nominal System Voltage | 12V/24V | ||
| Battery Voltage Range | 9~30V | ||
| Rated Charging Current | 25A | 35A | 45A |
| Conversion Efficiency | ≤98% | ||
| Max. Power Point Tracking Efficiency | >99% | ||
| Temperature Compensation | -3mV/℃/2V (default) | ||
| Self-Consumption | 44mA/12V; 26mA/24V | ||
| DC Output Parameters | |||
| Rated DC Output Current | 15A | 20A | 25A |
| General Parameters | |||
| IP Class | IP32 | ||
| Operating Temperature Range | -35℃~+45℃ | ||
| Humidity Range | ≤95% Non-condensing | ||
| Altitude | <3000m | ||
| Dimensions (LxWxH) | 160x115x51mm | 195x135x65mm | |
| Net Weight | 500g | 900g | 1035g |
9. Maintenance
To ensure optimal performance and longevity of your PowMr MPPT Solar Charge Controller, regular maintenance is recommended:
- **Cleaning:** Periodically clean the exterior of the controller with a dry, soft cloth. Ensure no dust or debris accumulates on the heat sink fins to maintain proper cooling.
- **Connections:** Annually check all wiring connections for tightness and corrosion. Loose connections can lead to power loss or overheating.
- **Ventilation:** Ensure the installation area has adequate ventilation to prevent overheating. Do not block the air vents on the controller.
- **Firmware:** Check the manufacturer's website periodically for any firmware updates that may improve performance or address known issues.
10. User Tips
- **Battery Compatibility:** Always ensure your battery type is correctly selected in the controller settings to prevent damage and ensure efficient charging. Refer to section 5.2 for details.
- **Wiring Order:** Strictly follow the recommended wiring order (Battery first, then Load, then PV) during installation and the reverse order for disconnection to avoid potential damage to the controller or other components.
- **Monitoring:** Regularly check the LCD screen for working modes and any fault codes to quickly identify and resolve issues.
- **PV Voltage:** Pay attention to the maximum PV open-circuit voltage (100VDC) and ensure your solar array configuration does not exceed this limit.
11. Warranty and Support
The PowMr MPPT Solar Charge Controller comes with a 12-month warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use conditions.
For technical support, warranty claims, or further assistance, please contact your retailer or the official PowMr customer service. Ensure you have your purchase receipt and product model information ready when contacting support.