Hobbywing Skywalker V2 Series ESC

Contents

Hobbywing Skywalker V2 Series ESC Instruction Manual

Model: Skywalker V2 Series (15A-160A)

Brand: Hobbywing

1. Introduction

This manual provides essential information for the safe and efficient operation of your Hobbywing Skywalker V2 Series Electronic Speed Controller (ESC). The Skywalker V2 series offers a range of ESCs from 15A to 160A, designed for various RC aircraft applications including airplanes and helicopters. These ESCs feature high-performance processors, multiple protection functions, and programmable parameters to suit your specific needs.

Video 1: Overview of Hobbywing Skywalker V2 Series ESCs.

2. Safety Precautions

Always observe the following safety guidelines to prevent personal injury and damage to your equipment:

  • Battery Connection: Ensure correct polarity when connecting the battery. Incorrect connection will cause immediate damage to the ESC and battery.
  • Insulation: Properly insulate all connections to prevent short circuits.
  • Motor Compatibility: Use only with compatible brushless motors.
  • Power Off Sequence: Always disconnect the battery from the ESC before disconnecting the ESC from the receiver or motor.
  • Heat Management: ESCs can generate significant heat during operation. Ensure adequate ventilation and avoid touching the ESC immediately after use.
  • Water and Moisture: Keep the ESC away from water and moisture unless it is specifically rated as waterproof.
  • Children: Keep the product out of reach of children.

3. Specifications

The Hobbywing Skywalker V2 series offers various models with different specifications. Please refer to the table below for details on common models:

ModelContinuous CurrentPeak Current (10s)Input (LiPo)BEC OutputWeightDimensions (LxWxH)
Skywalker 15A15A20A2-3S5V 2A (Linear)14g-
Skywalker 20A20A25A2-3S5V 2A (Linear)19g42x25x8mm
Skywalker 20A V2 Mini20A40A2-4S5V 2A (Switch)15g34x15x10mm
Skywalker 30A V2 Mini30A50A2-4S5V 3A (Switch)23g44x18x10mm
Skywalker 40A V240A60A3-4S5V 5A (Linear)36g60x25x8mm
Skywalker 50A V250A70A3-4S5V 5A (Switch)36g60x25x8mm
Skywalker 60A60A80A2-6S5V 3A (Switch)63g77x35x14mm
Skywalker 80A V280A100A3-6S5V 7A (Switch)79g85x36x9mm
Skywalker 100A V2100A120A3-6S5V 7A (Switch)92g85x36x9mm
Skywalker 120A V2120A150A3-8S5V/6V/7.4V/8.4V 10A/30A (Switch)117g83x35x22mm
Skywalker HV 130A OPTO V2130A160A6-14SNo BEC253.2g104x48x29mm
Skywalker HV 160A OPTO V2160A200A6-14SNo BEC262.8g104x48x29mm

Note: "OPTO" models do not include a BEC (Battery Eliminator Circuit) and require an external power source for the receiver and servos.

4. Package Contents

Your Hobbywing Skywalker V2 Series ESC package typically includes:

  • Hobbywing Skywalker V2 Series ESC (specific amperage model purchased)
  • User Manual (this document or similar)
  • Heat shrink tubing (for some models, for connector insulation)
  • Optional: LED Program Card (may be included or sold separately)
Skywalker 50A ESC with user manual and heat shrink

Image 1: Example package contents for a Skywalker 50A V2 ESC.

5. Setup and Installation

Follow these steps for proper installation of your ESC:

  1. Connect to Motor: Connect the three output wires from the ESC to the three motor wires. The order of connection may affect motor rotation direction. If the motor spins in the wrong direction, swap any two of the three wires.
  2. Connect to Receiver: Plug the signal cable (usually a three-wire cable: yellow/white, red, black/brown) from the ESC into the throttle channel (TH channel) of your RC receiver.
  3. Connect Battery: Connect the battery connector to the ESC's power input wires. Ensure correct polarity (red to positive, black to negative). If your ESC did not come with pre-installed battery connectors, you will need to solder appropriate connectors (e.g., XT60, Deans) to the ESC's power input wires.
  4. Secure ESC: Mount the ESC securely in your aircraft, ensuring good airflow for cooling.
Hobbywing Skywalker 30A V2 ESC with connection wires

Image 2: A Skywalker 30A V2 ESC showing input and output wires.

Throttle Range Calibration

It is crucial to calibrate the throttle range when using a new Skywalker ESC or a new transmitter. This ensures the ESC correctly recognizes the throttle stick's full range.

  1. Turn on your transmitter and set the throttle stick to its maximum position.
  2. Connect the battery to the ESC. The motor will emit a series of beeps.
  3. When you hear the confirmation tone (usually a long beep), move the throttle stick to the minimum position.
  4. The motor will emit another series of beeps, indicating successful calibration.

6. Operating Instructions

Once installed and calibrated, your ESC is ready for operation:

  • Power On: Connect the flight battery to the ESC. The ESC will initialize and emit tones.
  • Arming: After initialization, move the throttle stick to the lowest position to arm the ESC. You should hear a confirmation tone.
  • Flight: Slowly advance the throttle stick to control motor speed.
  • Power Off: Always reduce throttle to zero, then disconnect the flight battery from the ESC.

7. Programmable Parameters

Skywalker V2 ESCs feature programmable parameters that can be adjusted using an LED Program Box or your transmitter. This allows customization for various aircraft types and flight styles. Note: Values marked with an asterisk (*) are factory default settings.

Programmable Parameters table for 120A, 130A, and 160A Skywalker V2 ESCs

Image 3: Programmable parameters for Skywalker V2 ESCs (120A, 130A, 160A models shown).

Common programmable items include:

  • Brake Type: Options like Disabled, Normal, Reverse, Linear Reverse.
  • Brake Force: Low, Medium, High.
  • Voltage Cutoff Type: Soft, Hard.
  • LiPo Cells: Auto Calc, 3S, 4S, 5S, 6S (for 120A) or 6S-14S (for HV models).
  • Cutoff Voltage: Disabled, Low, Medium, High.
  • Start-up Mode: Normal, Soft, Very Soft.
  • Timing: Low, Medium, High.
  • Active Freewheeling: On, Off.
  • Search Mode: Off, 5min, 10min, 15min.
  • BEC Voltage: 5V, 6V, 7.4V, 8.4V (for models with adjustable BEC).

Special Features:

  • Reverse Brake: This feature, including Linear Reverse Brake, allows for shorter landing distances, simulating real aircraft landing. Normal and no-brake modes are also available. The brake amount is adjustable in normal brake mode. (Hobbywing registered patented feature).
    RC airplane demonstrating reverse brake feature

    Image 4: Illustration of the Reverse Brake feature.

  • Search Mode: This feature allows the pilot to activate the ESC to emit an audible beeping tone from the motor. This helps locate a lost aircraft in hard-to-see areas. It can also prompt the user to disconnect the battery if the ESC has been inactive for a set time, preventing battery drain and damage.
    ESC with sound wave graphic illustrating search mode

    Image 5: Illustration of the Search Mode feature.

  • DEO Technology / Active Freewheeling: Driving Efficiency Optimization (DEO) technology provides fast and smooth throttle response, better stability, and flexibility during flight. It also results in lower ESC operational temperatures and longer flight times. For 3D aerobatics, it is recommended to turn off this function.
    DEO Technology benefits: Flexibility, Lower ESC temperatures, Longer flight time

    Image 6: Benefits of DEO Technology / Active Freewheeling.

8. Multiple Protections

The Skywalker V2 ESCs are equipped with multiple protection features to ensure safety and prolong the lifespan of the unit and connected components:

  • Abnormal Input Voltage Protection: Protects against incorrect input voltage.
  • Low Voltage Cutoff: Prevents over-discharge of the battery.
  • ESC Thermal Protection: Safeguards the ESC from overheating.
  • Throttle Signal Loss (Fail Safe): Ensures the motor stops or reduces power if the throttle signal is lost.
RC airplane flying over mountains with icons for Abnormal Input Voltage, Low Voltage Cutoff, ESC Thermal, Throttle Signal Loss

Image 7: Visual representation of multiple protection features.

9. Maintenance

To ensure optimal performance and longevity of your ESC:

  • Keep Clean: Regularly clean the ESC to remove dust, dirt, and debris. Use a soft brush or compressed air.
  • Inspect Connections: Periodically check all wire connections for signs of wear, corrosion, or loose contacts.
  • Heat Management: Ensure the ESC is always operated within its recommended temperature range. If it consistently runs hot, consider improving airflow or reducing load.
  • Storage: Store the ESC in a dry, cool place away from direct sunlight and extreme temperatures.

10. Troubleshooting

ProblemPossible CauseSolution
Motor does not start or stuttersIncorrect throttle calibration; loose motor connections; one motor phase not working.Perform throttle range calibration; check and secure all motor connections; inspect motor wires and ESC for damage.
ESC overheatsInsufficient airflow; excessive load on motor/propeller; incorrect timing setting.Improve ventilation around ESC; use a smaller propeller or motor with lower current draw; adjust motor timing (if applicable). Consider adding a passive aluminum cooler.
Motor runs in wrong directionIncorrect motor wire connection order.Swap any two of the three motor wires connected to the ESC.
No response from ESC/motorBattery not connected; signal cable loose/incorrectly connected; damaged ESC/receiver.Check battery connection and charge; ensure signal cable is firmly plugged into the correct receiver channel; test with another ESC/receiver if possible.

11. User Tips

  • Authenticity: Many users confirm the product is genuine Hobbywing and performs as described.
  • Performance: The ESCs are noted for good performance, handling peak currents without issues, and running cool under typical loads (e.g., 30A).
  • Programming Card: An LED program card is highly recommended for quick and error-free programming of Skywalker V2 ESCs.
  • Connectors: Be aware that battery connectors may not be pre-installed, requiring soldering of your preferred connector type.
  • Cooling: For sustained high loads or in warm environments, consider adding a passive aluminum cooler rib to the ESC for improved thermal management.
  • Compatibility: The ESCs are suitable for various RC models including airplanes, cars, speedboats, and some drones, depending on the specific amperage and motor requirements.

12. Warranty and Support

Hobbywing products are manufactured to high-quality standards. For warranty claims or technical support, please contact the authorized Hobbywing distributor or the seller from whom you purchased the product. Keep your proof of purchase for warranty validation.

For further assistance, refer to the official Hobbywing website or contact their customer service department.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.