1. Introduction
The JIKONG Smart BMS (Battery Management System) is an intelligent protection board designed for large capacity series lithium battery packs. It offers comprehensive management and protection features to ensure the safety and longevity of your battery system.
This BMS is suitable for Li-Ion, LiFePo4, and LTO battery types and supports various cell configurations from 8S to 24S, with a continuous charging and discharging current of up to 40A.
2. Key Features
The JIKONG Smart BMS offers a wide range of features for optimal battery management:
- Active Equalization: High current active balancing (up to 0.4A continuous) to ensure battery consistency and prolong battery life.
- Voltage Acquisition: High precision voltage acquisition (±3mV).
- Current Acquisition: High precision current acquisition.
- Protection Functions: Overcharge, over-discharge, overcurrent (charge/discharge), over-temperature, low-temperature, and short-circuit protection.
- Communication: Bluetooth for mobile APP control (Android and iOS), optional RS485 and CAN communication.
- Monitoring: Support for external display screens and GPS for location tracking.
- Heating Function: Optional heating to prevent performance degradation in low temperatures.
- Alarm Function: Alerts for safety risks such as over-temperature or over-discharge.
- Battery Parallel Function: Supports parallel battery pack configurations (requires parallel modules).
- Intelligent Sleep: Energy-saving mode when the BMS is in standby.
- Emergency Switch: Provides a 30-minute operational window during critical events.
3. Setup & Installation
3.1. Packing List
Before installation, verify that all components are present:
- BMS x 1
- Switch key x 1 (long 50cm)
- NTC x 1 (long 40cm)
- Sampling line B x 1 (long 70cm)
- Sampling line A x 1 (long 70cm)
3.2. Product Appearance and Interfaces
The BMS features various interfaces for connectivity and monitoring. The overall dimensions for the JK-BD4AxxS-10P series protection board are 146.8mm × 103mm × 17.6mm.
Refer to the detailed interface definition table for pin assignments:
| Pin No. | Name | Definition |
|---|---|---|
| 1 | B- | Total negative battery |
| 2 | B1 | The first battery positive |
| ... | ... | ... |
| 15 | B14 | The fourteenth battery positive |
Note: For a complete list of pin definitions for P1, P2, P3, P4, P5, P6, P7, P8, P9, and D1, please refer to pages 21-23 of the official user manual PDF.
3.3. Wiring Method
The wiring method varies depending on the number of cells in your battery pack (7-24 series). Always ensure correct connections to prevent damage to the BMS or battery.
- Connect all the cables.
- Insert the cables into the BMS.
- Connect the B-line and the P-line to the battery.
3.4. APP Installation and Device Activation
The JIKONG Smart BMS can be managed via a mobile APP (Android and iOS). Scan the QR code below to download the APP. Android Version 7 or higher is required.
Device Activation: Before powering on the BMS, ensure all balance cables are properly connected and the P- and B- lines are correctly wired. The BMS is designed for charging activation; connect a charger (voltage 2V higher than battery voltage) to activate it. Alternatively, if you have an optional display screen and button, insert the cable into the display interface and press the button to activate.
4. Operation
4.1. Active Equalization
The BMS uses active equalization to transfer energy from higher voltage cells to lower voltage cells, maintaining battery consistency. You can set parameters like trigger equalization differential pressure (mV) and balance current (recommended not to exceed 0.2C of battery capacity) via the APP. The default balance current is 0.4A.
4.2. Monitoring and Communication
The BMS supports multi-screen display and data connection. You can view real-time information such as voltage, current, temperature, and number of strings via the mobile APP, PC software, or a dedicated JIKONG home storage display.
The BMS also supports protocol docking with mainstream inverter communication protocols. Parameters can be easily set up through the mobile APP or host computer.
4.3. Protection Functions
The BMS includes comprehensive protection features:
- Overcharge Protection: Prevents battery overcharging by cutting off charging when cell voltage exceeds set limits.
- Discharge Undervoltage Protection: Stops discharge when cell voltage drops below safe levels.
- Overcurrent Protection: Protects against excessive charge and discharge currents.
- Temperature Protection: Monitors and protects against both high and low temperatures during charging and discharging.
- Short Circuit Protection: Automatically protects against short circuits.
- Emergency Switch: Allows temporary operation for 30 minutes during critical events.
5. Maintenance
To ensure optimal performance and longevity of your JIKONG Smart BMS, follow these maintenance guidelines:
- Regular Monitoring: Use the mobile APP or external display to regularly check battery voltage, current, and temperature.
- Firmware Updates: Keep the BMS firmware updated to the latest version for improved performance and new features. Check the JIKONG website or APP for updates.
- Physical Inspection: Periodically inspect the BMS and wiring for any signs of damage, loose connections, or corrosion. Ensure the aluminum alloy shell is clean and free from obstructions to maintain proper heat dissipation.
- Parameter Review: Occasionally review the parameter settings in the APP to ensure they are appropriate for your battery type and usage conditions.
6. Troubleshooting
The BMS is equipped with an alarm function to notify you of potential issues. If an alarm is triggered or you experience unexpected behavior, consider the following:
- Over-temperature/Low-temperature: If the BMS triggers a temperature alarm, check the ambient temperature and ensure proper ventilation. For low-temperature conditions, consider using the optional heating function.
- Overcharge/Over-discharge: If these protections are activated, verify your charger/load settings and battery parameters in the APP. Ensure the battery type and voltage limits are correctly configured.
- Overcurrent: If an overcurrent protection is triggered, check the load and charging current. Adjust the continuous current settings in the APP if necessary, ensuring they do not exceed the BMS's design limits.
- Short Circuit: If a short circuit protection occurs, immediately disconnect the battery and inspect all wiring for any shorts. Increase the short circuit protection delay in the APP if transient high currents (e.g., from motor startup) are causing false triggers.
- BMS Not Activating: Ensure balance cables are correctly connected and the P- and B- lines are secure. Activate the BMS by connecting a charger with a voltage 2V higher than the battery, or use the optional display/button.
- Communication Issues: If the APP cannot connect via Bluetooth, ensure Bluetooth is enabled on your device and the BMS. For RS485/CAN communication, verify wiring and protocol settings.
7. Specifications
Below are the basic parameters and default settings for the JIKONG Smart BMS:
7.1. Basic Parameters
| Parameter | Value | Unit |
|---|---|---|
| Supply Voltage | 20-100 | V |
| Operating Power Consumption | <800 | mW |
| Operating Temperature | -30-70 | °C |
| Max. Number of Collection Strings | 24 | String |
| Max. Balancing Current | 0.4 | A |
| Max. Charging Current | 100 | A |
| Max. Discharge Current | 100 | A |
| Max. Instantaneous Current | 200 | A |
| Max. Internal Loop Resistance | 1 | mΩ |
| Protective Plate Size | 146.8*103*17.6 | mm |
| Finished Weight | 230 | g |
7.2. Default Parameters (Example for LiFePo4)
| Parameter | Value | Unit |
|---|---|---|
| Balancing Initial Voltage | 3 | V |
| Max. Balancing Current | 0.4 | A |
| Unit Overcharge Voltage | 3.6 | V |
| Overcharge Protection Recovery | 3.55 | V |
| Monomer Undervoltage Protection | 2.6 | V |
| Undervoltage Protection Recovery | 2.65 | V |
| Automatic Shutdown Voltage | 2.5 | V |
| SOC-0% Voltage | 2.6 | V |
| SOC-100% Voltage | 3.5 | V |
| Trigger Balancing Differential Pressure | 0.01 | V |
| Charging Overcurrent Protection Delay | 30 | S |
| Charging Overcurrent Release Time | 60 | S |
| Discharge Overcurrent Protection Delay | 300 | S |
| Discharge Overcurrent Release Time | 60 | S |
| Short-circuit Protection Delay | 5 | uS |
| Charging Overtemperature Protection | 70 | °C |
| Charging Overtemperature Recovery | 60 | °C |
| Discharge Overtemperature Protection | 70 | °C |
| Discharge Overtemperature Recovery | 60 | °C |
| Charging Low Temperature Protection | -20 | °C |
| Charging Low Temperature Recovery | -10 | °C |
| MOS Overtemperature Protection | 100 | °C |
| MOS Overtemperature Recovery | 80 | °C |
Note: For detailed default parameters for Li-Ion and LTO battery types, please refer to pages 18-19 of the official user manual PDF.
7.3. Product Models and Compatibility
The JIKONG Smart BMS is available in various models supporting different battery string counts and optional features:
| Product Model | Battery Type | Adaptive Battery Strings |
|---|---|---|
| JK-BD4A24S-10P | Ternary Lithium Battery | 7 ~ 24 |
| Lithium Iron Battery | 8 ~ 24 | |
| Lithium Titanate Battery | 14 ~ 24 | |
| JK-BD4A20S-10P | Ternary Lithium Battery | 7 ~ 20 |
| Lithium Iron Battery | 8 ~ 20 | |
| Lithium Titanate Battery | 14 ~ 20 |
Note: The 'P' suffix in the model number indicates a common port BMS. Specific models like JK-BD4A24S-10PC (with CAN communication) or JK-BD4A24S-10PHR (with heating and RS485) are available based on selected features. Refer to page 10 of the official user manual PDF for a complete function selection guide.
7.4. Application Scenarios
The JIKONG Smart BMS is versatile and can be used in a variety of applications:
8. User Tips
- Bluetooth Connectivity: Many users appreciate the Bluetooth feature for easy monitoring. Ensure your mobile device's Bluetooth is on and within range for seamless connection to the BMS APP.
- Choosing the Right Model: When selecting a BMS, consider your battery's series (e.g., 4S, 8S, 24S) and desired communication features (e.g., Bluetooth, RS485, CAN) to ensure compatibility and functionality.
- Parameter Customization: Take advantage of the APP's parameter setting options to fine-tune protection values and balancing currents according to your specific battery chemistry and capacity for optimal performance.
9. Warranty & Support
For detailed warranty information and technical support, please refer to the official JIKONG user manual PDF. The PDF contains comprehensive information on product specifications, interface definitions, and operational instructions.
You can access the full user manual PDF here: JIKONG Smart BMS User Manual (PDF).
JIKONG is committed to providing high-quality products and support. The company has a strong R&D team and adheres to strict quality standards, including ISO9001 certification.