1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the QIACHIP RX480E RF Relay Receiver Module and its accompanying Remote Control Transmitter. This system is designed for various DIY applications requiring wireless control, such as garage doors, electronic gates, and other telecommand equipment.

2. Specifications
| Feature | Specification |
|---|---|
| Model Number | KT01-117S-4+RX480E-4+ANT-240 |
| Brand Name | QIACHIP |
| Item Type | SWITCHES |
| Switch Type | Remote Control |
| Working Voltage | DC 3V~5V (Receiver Module) |
| Working Frequency | 433.92MHz (RX480E-4); 315MHz (RX480E-3) |
| Receiving Sensitivity | -108dBm |
| Quiescent Current | <= 5mA |
| Modulation Mode | ASK |
| Matching Mode | Intelligent Learning Code (1527 Common Chip) |
| RF Working Mode | Superheterodyne |
| Working Modes | Momentary, Toggle, Latching |
| Remote Distance | 15m (up to 100m in open space) |
| Material | Copper |
| Module Dimensions | 28mm x 12.3mm x 8mm (including pin thickness) |
| Operating Temperature | -40℃ to 85℃ |
| Certification | RoHS, CE, CCC |
| EU LVD Voltage | Low voltage: Below 50Vac or 75Vdc |
| Current | 5A |
3. Package Contents
- 1 x RX480E RF Relay Receiver Module
- 1 x Remote Control Transmitter (4-channel)
- 1 x 433MHz Antenna (if selected)
4. Setup & Installation
4.1 Pin Definition and Module Size
The RX480E module features several pins for power, data output, and an external pairing button. Refer to the diagram and table below for pin identification and module dimensions.

| Pin No. | Name | Description |
|---|---|---|
| 1 | GND (-) | Negative pole of power supply |
| 2 | V (+) | Positive electrode of power supply (3V-5V) |
| 3 | D0 | Signal output pin corresponds to remote control button value 1 (0001) |
| 4 | D1 | Signal output pin corresponds to remote control button value 2 (0010) |
| 5 | D2 | Signal output pin corresponds to remote control button value 4 (0100) |
| 6 | D3 | Signal output pin corresponds to remote control button value 8 (1000) |
| 7 | VT | External pairing button (High level active) |
| 8 | ANT | Antenna |
4.2 Wiring Instructions
The RX480E module can be connected to various circuits, such as LED indicators or relay circuits, depending on your application. Below is a typical wiring diagram for connecting to LED indicators.

For more complex applications involving relays, refer to the detailed circuit diagram provided in the official PDF manual. The PDF manual also contains a diagram for connecting to a relay circuit.
4.3 Antenna Connection
Proper antenna connection is crucial for optimal performance. The module supports both 315MHz and 433MHz antennas. Ensure the antenna is connected to the 'ANT' pin (Pin 8).
General Antenna Specifications (433MHz)
- Antenna core diameter (including outer skin): 1.0mm
- Antenna core diameter (excluding outer skin): 0.35mm
- Length of wire at welded end: 12mm
- Diameter of antenna winding (excluding outer skin): 3.0mm
- Winding turns: 26 turns
- Length of winding: 36mm

For detailed specifications on 315MHz antennas or enhanced antenna configurations for longer communication distances, please refer to the official PDF manual.
5. Operating Instructions
5.1 Remote Control Transmitter
The remote control transmitter features multiple buttons for controlling the receiver module. It is designed for ease of use with an antiskid cover and an indicator light.

5.2 Working Modes
The RX480E receiver module supports three primary working modes: Momentary, Toggle, and Latching. These modes define how the receiver's output reacts to button presses on the remote control.


Momentary Mode (Jog Mode / Inching Mode)
- Function: The relay connects (output high-level signal) only while the remote button is pressed. It disconnects (output low-level signal) immediately upon release.
- Setting: Press the learning button on the receiver once.
Toggle Mode (Self-lock Mode)
- Function: Press the remote button once, the relay connects (output high-level signal) and stays connected. Press the same remote button again, the relay disconnects (output low-level signal).
- Setting: Press the learning button on the receiver twice.
Latching Mode (Interlock Mode)
- Function: This mode typically involves multiple buttons. Press remote button A, relay connects. Press remote button B, relay disconnects.
- Setting: Press the learning button on the receiver three times.
5.3 Learning the Code (Pairing Remote Control)
The receiver module uses an intelligent learning code (1527 Common Chip) for pairing with remote controls. The process varies slightly depending on the desired working mode.
General Steps for Pairing:
- Select Mode: Press the learning button on the receiver module the required number of times for your desired mode (1 for Momentary, 2 for Toggle, 3 for Latching).
- Enter Learning State: Wait for a moment; the LED indicator on the receiver will turn off, indicating it has entered the learning state.
- Press Remote Button: Push the desired button on your remote control. The LED indicator on the receiver board will flash and then turn off.
- Confirmation: After approximately 3 seconds, the LED indicator will turn on again, signifying successful learning.
Special Note for Latching Mode Pairing:
When setting up Latching mode, you typically need to pair two different buttons from the remote control: one for "ON" and one for "OFF".
- Enter Latching Mode: Press the learning key on the receiver three times.
- Enter Learning State: Wait for the LED indicator to flash and then turn off.
- Pair "ON" Button: Press remote button A (e.g., for ON). The LED will flash 5 times.
- Pair "OFF" Button: Press remote button B (e.g., for OFF). The LED will flash 5 times.
- Confirmation: After 3 seconds, the LED indicator will turn on again, indicating successful pairing for Latching mode (A=ON, B=OFF).
5.4 Reset Module (Clear All Paired Remotes)
- Steps: Press the learning button on the receiver module eight times. This will clear all previously paired remote controls.
6. Precautions
- This product is a CMOS device. Pay attention to anti-static measures during storage, transportation, and use to prevent damage.
- Ensure the device is well-grounded during use.
- RF devices are sensitive to voltage fluctuations. If the power supply is unstable or has significant ripple, add a filter at the power input. Ensure the power supply voltage does not exceed the maximum working voltage of the product (DC 5V).
7. Troubleshooting
- Issue: Remote control not responding.
- Check Power: Ensure the receiver module is correctly powered (DC 3V-5V).
- Check Pairing: Verify that the remote control is properly paired with the receiver. If unsure, try re-pairing according to the "Learning the Code" section.
- Remote Battery: Check if the remote control's battery needs replacement.
- Obstructions/Range: Ensure there are no significant obstructions between the remote and receiver, and that you are within the effective operating range (up to 15m, or 100m in open space).
- Issue: Output signal is erratic or unreliable.
- Power Stability: Check the stability of the power supply. Add a filter if necessary, as mentioned in precautions.
- Interference: High RF interference in the environment can affect performance. Try relocating the module or reducing sources of interference.
- Antenna Connection: Ensure the antenna is securely connected and correctly sized for the operating frequency.
- Issue: Cannot change working mode.
- Button Press Count: Ensure you are pressing the learning button the correct number of times for the desired mode (1, 2, or 3 presses).
- Timing: The timing between presses and during the learning state is important. Follow the steps precisely.
8. User Tips
- Multiple Receivers with One Transmitter: Yes, you can control different receivers with the same transmitter by pairing each receiver to the desired buttons on your single transmitter. This is useful for controlling multiple devices independently or simultaneously.
- Garage Door Application: This module is suitable for opening and closing garage doors. Ensure proper wiring to your garage door opener's control circuit, typically using the momentary mode for activation.
- Antenna Optimization: For maximum range, ensure the antenna is straight and away from metal objects that could cause interference or shield the signal.
- Testing Modes: Before final installation, test each working mode (Momentary, Toggle, Latching) with a simple LED setup to understand its behavior and confirm it matches your application needs.
9. Warranty & Support
This product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support or warranty claims, please contact your retailer or the manufacturer directly.
For additional item guides and documents, including detailed circuit diagrams and advanced configurations, please refer to the official user manual PDF: View User Manual (PDF).